How to Test Optocouplers and Opto-isolators with a Multimeter
Ғылым және технология
❤️You can Support the channel and help purchase photography and recording equipment❤️👇
✅Donate: paypal.me/ElectronicsRB?count...
My Facebook Group:
/ 723491633169505
My website:
www.prospace20.com/
How to diagnose & repair a Dead laptop motherboard course👇👇👇
www.prospace20.com/2022/03/ho...
Buy Repair Tools👇👇👇
northridgefix.com/shop/?ref=E...
Microscope
Voltage Injector
Programmers
Reballing / Stencils
Repair Tools
iPhone Cases
Soldering
Soldering Equipment
Storage / Rack
SMD Books
Tempered Glass
Test Tools
Components
Donor Boards
Gadgets / Accessories
Ports / Connectors
Tweezers
Adhesive
Apparel
And much more
Пікірлер: 38
Thank for your efforts in explaining how to test Optocouplers
@electronicsrepairbasics_erb
Жыл бұрын
So nice of you
Awesome explaination.Thanks brother.Pakistan
@electronicsrepairbasics_erb
Жыл бұрын
My pleasure
Thanks for the detailed explanation.
@electronicsrepairbasics_erb
Жыл бұрын
You are welcome!
Genius explanation. Thanks a lot. 🇪🇹
@electronicsrepairbasics_erb
Жыл бұрын
Glad it was helpful!
Helpful! Thx for your video.
@electronicsrepairbasics_erb
Жыл бұрын
So welcome
Brilliant,thank you 🙏
@electronicsrepairbasics_erb
8 ай бұрын
You're most welcome!
Toujours aussi efficace
Oh..Great ..Thanks you soo much ..
@electronicsrepairbasics_erb
Жыл бұрын
You are very welcome
Thanks
@electronicsrepairbasics_erb
4 ай бұрын
Welcome
Great!Great!Great!
Should 1100 come out without AC 220V power supply?
Can this be used to reset a Z80 cpu, by connecting the collector to ground and the emitter to the /RST pin?
you are very good to expain but please change your mic
Nice work, please i need a detailed video on how to use digital multimeter for a beginner
@electronicsrepairbasics_erb
Жыл бұрын
Noted!
Q) It the transistor is damaged/open, you would also get no reading on Pins 3+4, so wouldn't you also need to test that the emitter and collector connect when the diode/LED illuminates the photosensitive base? Thx.
Hi. I Dndid the same like you. I testes the diode-OK. When I test the transistor part, I get around 1 volt. But when take it out from the board, I then get nothing. Is that OK? How should it be tested?
I'm a total electronics moron - but why others are using some more complicated methods of testing opto-isolators eg. one guy desoldered from the board and connected all 4 pins and use a resister and battery etc. Can I test an opto isolator "your way" directly on a board? (no desoldering involved). Thanks
@SolderBrothers
11 ай бұрын
It gets complicated. In circuit, no soldering, you may get readings from other components in the circuit. This is a good base test to show shorts or opens on the opto. Of course a short elsewhere in the circuit will show a short on the opto.
How do we know is it optocoupler or an IC by doing it visualy when it still on circuit?? Is it any sign?
@surgingcircuits6955
Жыл бұрын
I recommend 1st to read the marking, and internet search the number(s) you find. If you have more knowledge... Optocouplers are a non-contact way to connect 2 circuits on a PCB that may be operating at different voltages, so look at the PCB circuits and see if the device appears to be "isolating" the two circuits. The transistor side (pins 3+4) are acting like a switch for the 2nd circuit. Similar to how a "relay" works ... just using light to activate vs using mechanical means.
1000 what? there is no 1000 there unless it is mV; is it? thanks because you're testing them in circuit, do those readings depend on the circuit or not? thanks
In case I need help in one cicuit, can you help and give explanation?
@electronicsrepairbasics_erb
11 ай бұрын
You are very welcome Pierre, Join me on Patreon Page for more unique content
good
@electronicsrepairbasics_erb
Жыл бұрын
Thanks
Very nice😋👏!!! Don't miss out = "Promo sm" !!
@electronicsrepairbasics_erb
Жыл бұрын
Thank you
Thanks
@electronicsrepairbasics_erb
Жыл бұрын
Welcome