Good video, thanks

Thanks for sharing ADP👍 Really valuable information👍

@ADPTraining

4 жыл бұрын

Thank you...

@ADPTraining

4 жыл бұрын

autodiagnosticsandpublishing.com/

How about resetting the adaptation on the VTG module, say after an oil change on the transfer case? Can the Autel do this?

@ADPTraining

3 жыл бұрын

For an aftermarket scanner, the AUTEL MaxiSys is the most complete. autodiagnosticsandpublishing.com

Hello, 2011 model BMW x6 car gives this fault code: 5F39 4x4 and ESP ABS fault lights are on

Great Video

I had the abs,brake,and 4x4 light on the dash. I replaced actuator and tore apart old actuator and found plastic gear stripped. Well two weeks later the lights are back and they come on every time I drive it. When I first replaced it I was getting a clunk noise when taking off fast, but no clunky when taking off slow. Front end sounded like something was worn. Now that lights are back on I hear no clunking sound. What do you think is going on

@ADPTraining

Жыл бұрын

1- need to relearn new gear or transfer. 2- might have damaged front end due to torn gear.

Hello changed the actuator and resistor myself on my x3 and it feels much better and lights gone but feels like its dragging sometimes i have the code “54C4 First calibration defective” Reset it with basic scanner and the code comes back do i need a special scanner is my transfer case bad? Thanks...

@ADPTraining

3 жыл бұрын

Yes, calibration has nothing to do with the resistor. The resistor is a coarse calibration if you will. Then, you need something like a manufacturer capable scanner. The AUTEL Maxisys comes to mind. Keep me posted. autodiagnosticsandpublishing.com

Hyy,I have the issue with Dsc abs brake light on I change transfer case actuator ..change abs module and yaw rate sensor..Right now my light is off and I drive 10 miles before I turn hard left they come on again and I feel like some braking behind..like some one push on rear brakes

@ADPTraining

4 жыл бұрын

Well, did you reset the adaptive memory? Looks complete related to an adaptive issue.

@ahmicahmic9757

4 жыл бұрын

@@ADPTraining I took my vehicle to mechanic and he reset and clear everything..And right now when I start the vehicle no lights..after 30 minutes they come on again..And my radio stop working too.thank you

Without oil,does the transfer case turn on the service engine soon?…thanks in advance.

@ADPTraining

Жыл бұрын

Without oil it'll turn ON your back account faster than SILICONE VALLEY BANK.

Hi, please if u can help me in my x5 2004. From a while The trifecta lights with dsc inactive came on, so i went to a mechanic that showed in his scanner the gearbox so i changed the gear with the actuator and new oil but it’s used and it’s spare parts from an x5 in japan. Anyway after changing it sometimes the dsc only comes on but when you turn on the car again it goes off. So i scanned the car and it gave the steering angle (code: 04 and 08 slider fault, adjustment operation) with the transfer case(code: 54C8 classification registor). So he told me u should change the steering angle, is that true because here in ur case did u change the steering???

@ADPTraining

2 жыл бұрын

You go with what you have, these CODES or DTCs. Concentrate on that, not what someone else did. Good luck.

@bilalhaidar3

2 жыл бұрын

@@ADPTraining so what u think i should change the steering or the gear?

I replaced actuator. Now when in gear I get a bad grinding noise...even at crawling speed 1-2mph. With actuator unplugged veh drives fine, no noise. But no 4wd either. Gear oil was low when I did actuator. Any thoughts on next steps?

@ckproper

3 жыл бұрын

Don't want to buy a new transfer case without a strong diagnosis

@ADPTraining

3 жыл бұрын

Raise vehicle, start and put in gear. Then manually actuate transfer gear somehow. See if noise persists and if so you may need a Xfer case.

@glenglene8473

9 ай бұрын

what is the issue?

@stevewalker7945

Күн бұрын

@@ADPTrainingsorry to ask questions 3 years later! I’ve just tried manually engaging mine on the TC, the stub there seems to spring when you turn it backwards and just clinch to a stop when turning forwards, is that normal?

BMW X6 2011-2012 when it turns left or right it doesn't make any noise but it feels bumps, but in a straight line it's normal, what could it be?

@erickss2010

4 ай бұрын

50i v8

When on x3 turning on full lock transmition feels like its fighting crabbing rear wheels trying to spin with this faukt code is it the gear

@ADPTraining

9 ай бұрын

Probably worn out X Drive

Does anyone out there know where to buy the parts to rebuild these transfer cases?

@ADPTraining

Жыл бұрын

BMW

Hello, I have a 2005 bmw X5 with the 4x4 light on the dash. I changed the gear on the actuator but the the light is still there. I noticed the vehicle cannot be driven for long as it goes into limp mode. I have to shut it off and then restart

@ADPTraining

Жыл бұрын

Check resistor on case body. May need to relearn with scanner.

@romeoholder4453

Жыл бұрын

@@ADPTraining okay can i test the resistor with a mulitmeter to see if it is good or not?

@romeoholder4453

Жыл бұрын

@@ADPTraining well I forgot to mention these codes 5EB3 DSC: Steering-angle-sensor-adjustment and 5F42 DSC: Transmission control, limp-home operation showed up on my scanner. Now i reset my SAS and now the 4x4 light is off, but the only problem now is that the car would drive changing gears for like 3 minutes and then suddenly drag and don't change gears until i shut it off for like a 1minute and restart it and drive. I changed the plastic gear on the actuator and test it by applying ground to pin 8 and power to pin 1 and it spins okay, i really don't know what else to do!

@romeoholder4453

Жыл бұрын

@@ADPTraining I would also like to add that i checked the wiring connections for the actuator with a test light, I am getting ground but when i test for power there is nothing even with ignition switched on. Is there any diagram showing what voltage suppose to go to each pin and also the resistor wiring?

Any help will helpfull thank you

@ADPTraining

2 жыл бұрын

Ok, ???

@ahmicahmic9757

2 жыл бұрын

@@ADPTraining no sir its same happened, I reset every code tpms ,.comes on it works everything for couple minutes as soon I stop and keep going the tpms light comes back again.

when this happen to me and it was the transfer case module under the front passenger seat carpet small silver box by the sub woofer speaker on an 2008 e90 so what i did i order this thing called xdelete and flashed out the transfer case so now its rear wheel drive untill i get some funds to fix it

@ADPTraining

Жыл бұрын

Rear drive, wow, didn't know that could work. Thanks.

@elmalkriao100

Жыл бұрын

Hey when you bought the xdelete did the lights all go away on the dash? And we’re you able to use the cruise control again?

@victorbregante845

Жыл бұрын

Hey did the lights go away when you flashed it?

@victorbregante845

Жыл бұрын

@@elmalkriao100 did you ever find out if it did?

@elmalkriao100

Жыл бұрын

@@victorbregante845 nope

Cool video, but my tracking must be off