Exactly what I was looking for, I have this kit and didn't know where to start, thank you very much sir. Perfect video

@EtherealProAV

2 жыл бұрын

Thanks SteveO! Glad to help

Excellent information thank you

Good instructions, thanks

@EtherealProAV

3 жыл бұрын

Hi Steven! Thanks for watching, we're glad it was helpful! - Adam

Thank you for this video. Would you please do a similar video on terminating using a multi-core cable with a uniboot terminator. There are a lot of videos out there showing how to change the polarity of uniboot terminators, but I couldn't find anything about best practices for actually installing a uniboot terminator.

Nice video 👍

@EtherealProAV

2 жыл бұрын

Thank you!

Good, but perhaps we could get clarity on Cladding? I think we're not talking about the same thing here. Ecmag does a great breakdown in their article "do not strip cladding when stripping fibers". Thanks.

Is it necessary to replace the measuring thing on the cleaver for installing the cold lc quick connector.

u say remove the cladding.ur not actually stripping the cladding. the cladding is part of the glass. what your are stripping at the last step is the plastic buffer coating. if I stripped the cladding somehow, the light would exit the core.

thanks

Perfect vedio

@EtherealProAV

2 жыл бұрын

Glad you think so! - Adam R.

Great video. Do you have someone who can answer additional questions for Metra account holders?

@EtherealProAV

2 жыл бұрын

Hello J V, Yes we do! Easiest way is to give us a call at 386-255-0234. Thanks! - Adam

Hi there, is it necessary to remove the cladding in order to assemble it to the connector? I thought removing the cladding will allow the light to exit the core and result in loss of quality? Or won´t make it a difference, once the core is fitted in the connector? Great video btw :)

@EtherealProAV

3 жыл бұрын

Hi Michael, great question! While the cladding does aid with the signal quality over the long lengths, its real purpose is to keep the glass from shattering when it is bent or curved. You'll notice if you try to strip the fiber then bend it where the cladding has been removed, it will be much easier to break. The shape of the fiber is what really keeps the light inside. Think of it like when you look through a fish tank full of water, you can see in the front and out the back, but you usually can't see out the sides of the tank. It's the same concept with the fiber, you can see the end and the beginning, but the sides become reflective (or refractive really) when looking at an angle. - Adam

@MEJBL

3 жыл бұрын

@@EtherealProAV I was unsure about removing it, so I stopped terminating the new fibers in my home and waited for your answer, now I will go on :) Thanks a lot for your answer, really helpful and informative.

@EtherealProAV

3 жыл бұрын

@@MEJBL Happy to help! Let us know how it goes! - Adam

@Shutite

3 жыл бұрын

@@EtherealProAV This is incorrect. The cladding is very important, and this video does not show removal of cladding. It shows 1) removal of the aqua jacket 2) removal of the white buffer 3) removal of the clear protective coating (not the "inner cladding"). The cladding and core remain after the 3rd step of the stripper.

Where can we purchase the entire kit as per above part numbers? We're a small ISP from South Africa (registered for import/customs).

@EtherealProAV

2 жыл бұрын

Hello Dewald! Reach out to our South African distributor - Elan Systems South Africa (elansystems.co.za) (elansystems.co.za/contact-us/) Thanks! - Adam

Thanks for this,

@EtherealProAV

3 жыл бұрын

Hi Rose, Happy to Help! Let us know if you need anything else! - Adam

Where to buy Grommet for these fibers?

do u know if the one connect cable is fixable?

@EtherealProAV

2 жыл бұрын

Hello Alejandro, Unfortunately, I do not believe there is an official way to repair the Samsung One Connect cable. It normally carries both data and power from either the panel to the connect or from the connect to the panel. I would suggest reach out to Samsung's customer support for further assistance. This page (www.samsung.com/us/support/troubleshooting/TSG01109041/) goes into detail about where to purchase a replacement cable. Good luck, and let us know how it goes. Thanks! -Adam R.

It says "OM3" - but how about OS2 ?

@EtherealProAV

2 жыл бұрын

Great question! OM3 is a roughly 100 micron wide glass fiber, where as OS2 is MUCH thinner. You may be able to adjust the tolerances down to that level, but it would be rather difficult to get it just right. - Adam R.

Price

next time don't bump the tip of the cleaved fiber. the tip for sure have a crack.

How much this misin

@EtherealProAV

3 жыл бұрын

Hello Bamshi, the best way to get pricing is to contact your sales rep for your area. visit metrahometheater.com/contact-us.html/ for more information. Thanks! - Adam

@HondaCBR60004

3 жыл бұрын

Good video but how bout cleaning the fiber?

@EtherealProAV

3 жыл бұрын

Hey @@HondaCBR60004, thanks for the question! It's good practice to clean the fiber before cleaving, however we've found negligible signal loss when we did not clean. So long as you do not touch the fiber AFTER you cleave it you should be fine as it's the end of the fiber that matters the most. - Adam

@carrieliu8081

2 жыл бұрын

@@HondaCBR60004 You can clean the fiber with dustless paper dipped in alcohol

কতো দাম

@EtherealProAV

2 жыл бұрын

Hopefully this translates correctly. আরও তথ্যের জন্য আমাদের আন্তর্জাতিক বিক্রয় প্রতিনিধির সাথে যোগাযোগ করুন। contact our international sales rep for more information.

Hi

@EtherealProAV

2 жыл бұрын

Hello!

@pingfenceenterprise

Жыл бұрын

Please I need kits where and how cani get one,here in ghana

Calibration tool...🤣

Wait wait wait. So you are saying no one does Manuel termination. Like using sand paper to get the core sanded down with the wheel???

@christianvizcarra9300

6 ай бұрын

That’s old school bud !! 😅

@edgardmartinez6026

6 ай бұрын

@@christianvizcarra9300 I used to do that here with the school district. I’m sure this is still done.