Use your impact wrench and you won't have to use a box wrench on top. BIG help!!! If you have a trailer, you can lower the ramp/gate and go up one side or the other, leaving one of the front wheels off the side of the gate. You can get right under the deck without using a jack.

A set of car ramps works very well and no danger of a 1200 lb. mower falling on you when you are cleaning the deck or changing blades. I paid about $30 for the composite ramps, they are stronger than the metal ones.

@thomas68morse

5 жыл бұрын

Mower is 900 lbs.

This technique worked great. Box wrench on the top while using the socket on the bottom was the key for me. Thanks for posting.

That is a wide deck and I saw one thing which worried me and that is the car jack which has been known to let the load drop. I got a special jack from Harbor Freight which is easy to lift the mower by the wheels and much higher and is safer. They are making mowers cheaper today with plastic parts rather than metal ones. That is why I have to look at the equipment before buying it today. I have a John Deere z445 mower and love it when it is working fine.

@semco72057

9 жыл бұрын

There is no name on the jack, but it is one they had on sale at the time for $79.95, which was a $10.00 discount at the time I got it. It is the type which has a pedal on the cylinder to pump up the mower using your feet, and another pedal to lower it. It also comes with a bolt to place in a hole provided so if the cylinder fails while the mower is jacked up, it won't fall. I used it to lift my lawn tractor and it lifted the unit very high so I could do anything under there.

@zaineridling

9 жыл бұрын

Sidney Mathious It's made by Hi-Lift. I have the Hi-Lift X-treme jack. I actually set mine in the yard and let the jack base dig in the ground slightly.

@semco72057

9 жыл бұрын

That is what I have to do also, though it isn't left there. i keep it under a shed when not in use. I recently used it on my Craftsman Lawn tractor to lift it up and replace a belt for a second time. This jack comes in handy for me and I don't think I do without it. It is an important tool for anyone.

Holy crap that is the hard way to do it. Drive a front tire up on a car ramp, Slide 3 ton jack under center front lip of the deck. Quickly jack it up. Grab impact gun with 15/16 socket and zip the blades right off. I can change a set of blades on a commercial zero turn in 2 minutes.

@scottwarner2827

5 жыл бұрын

I took the rear roll bar off and attached it to a rectangle motorcycle lift table. Then attached a winch on the top of roll bar. Drive on table, lift table 4 ft off ground and then winch the deck up and use air line to impact gun.

@neekbot

4 жыл бұрын

I can’t get my blades off without an impact gun

Thanks for keeping it simple with basic tools....

Thanks for your comments. I already have a pancake compressor 6 gallon 2 HP will it run a pneumatic impact gun for blade changes. If so, I will pick one up. I only need to change my blades about once every 2-3 weeks. I mow 5 acres a week. Please subscribe.

On that torch bar how high does it have to go did you say 100

Hi, I did what you said for the blade removal. How do i remove the hex bolt on the pulley to replace the entire spindle assembly?

3:15 You should never use a torque wrench to loosen fasteners. Thanks 4 the vid.

@berniemac8413

5 жыл бұрын

The elephant In the room a breaker bar.. or an impact gun.. 😎

This video is very informative and straight-forward. Thanks for posting.

Look at the MoJack mower lifts. I have the Pro model and love it. Very good safe investment.

Posted former post before I saw what looks to be an electric impact. Why didn't you use it? I've been running mowers and doing all of the routine maintenance for over 40 yrs never torqued to a specific ft/lb and never had a problem.

I've always use a 2x4 underneath to leverage against the blade then used mu ratchet to remove. Is this ok or could this cause a problem? Thanks

@scoresandry

Жыл бұрын

Thats fine, I've been doing it that way for years. Sorry for the late reply. lol

do you have a video on how to replace the spindles?

Another reason to use an impact wrench to loose/tighten the blades is to keep your friggin hands as far away from the blades as possible! I used to do it the way you show in the video, but last summer I had a mishap with the wrench on top of the deck popping loose as I was tightened the nut on the botton, and cut the back of my hand badly. Severed a tendon even. Now I use an impact wrench. I'll never do it manually again. Please don't make the mistake I made.

@jonimcmillian246

2 жыл бұрын

Wow, thanks for sharing that advice. I am new to doing stuff like this for myself and this is valuable information!

A small compressor and impact are well worth the $ when it comes to this! You'll wonder why you didn't get them sooner. :-)

What about round-holed blades? I can remove and install them with an impact tool but I can't torque them with a torque wrench. I'd need a pulley holder.

You should title this "how to drop a zero turn on your head" or "how not to work on mower blades" ishook my head at the 1970 jack, then i saw your backup safety bucket. I called OSHA btw

Jack stand looks like it's leaning, hope that's OK? Also, buckets can crack, I would never climb under that thing. Decent video, thanks for posting.

@RoczombieX

Жыл бұрын

Bucket can crack, or the wheel could roll

Looks like the front wheel spindles are bent back from hitting things in the yard. Mine do this on my finishing mower on my tractor.

Are the blade bolts left-handed threaded or??????

Good video I have a 2002 60 in master. In the 1950s bumper Jack. Never have your head above handle. At junk yard. Friend was jacking up car with bumper Jack. Started to lower with his head above Jack. Catch gave and Jack handle looked like machine gun it was moving so fast. Handle caught in under jaw. Right thru to teeth it was ugly. Big hole under chin and knocked teeth out. I'm 78 now never forget that. Floor jacks. Brother in law was going to lower large van. Bam Jack broke down it came. Lucky no parts of his body were under the van

Good video thanks...How about on how to remove the blade belt?

How did you break the belt in the toro mower

I can't get my blade off that not you put the Box end starts coming off instead of the blade I don't want to tighten that top one too much cuz I'm afraid I'll break it and then I'll have to buy a new one

I just sit on the floor put one boot on the blade and with the breaker bar on the blade bolt and push the blade w my foot , breaks the blades loose w very little effort . Otherwise sometimes the spindle and the blade want to come off together

That's a BIG deck!!

Where you get the jack ? also an item number would be nice so look it up ...

@zaineridling

9 жыл бұрын

Amazon, or your nearest farm supply store. Here's their website: www.hi-lift.com/hi-lift-jacks/x-treme.html

blade nut nut blade 3220-7 NUT-JAM blade retaining nut socket size

model number 74704 48" toro time cutter serial no. 260000001 The nuts are 3/4-16 SAE fine thread, and you use a 1 1/8" socket size to remove/install them. no lie.. i spent 4 hours on google trying to find the size of my nut (lol) and i finally found it on ebay a guy selling them.. thought id post this to help out the next guy. thanks.

I quit watching when the bumper jack appeared.

@westlandjeff

4 жыл бұрын

Not to mention the 5 gallon bucket under the front tire.

@bryantwhite5222

4 жыл бұрын

@jerome clements That guy is going to kill himself with that old ass Jack man. That thing is old as dirt. I haven’t seen one of these since I was 8 years old when my grandpa use to fix on his cars. 😂🤣😭

Great video. Probably out of my skill set, but still a good video.

Do you still have the lawn mower and just notice how old the video was

cool ..i was wondering how to pick up my 1,200 lb ZTR O_o ..thing is built like a tank...

@warmfreeze

10 жыл бұрын

also wouldnt it be easier to just drop the deck and work on it that way? most industrials you just pull 4 pins and drop the deck and pull mower off the deck..

The video helped a great deal thank you.

That what I do with my exmark 36 inch walk behind also good video its hopefully

@benitafullermcneil1534

8 жыл бұрын

u

@cichlid_nation5314

8 жыл бұрын

+Nita Loving My Life your what do you mean ?

Harbor Freights got a regular Jack for this

Thank you, that's very helpful

nice old bumper jack !!!

@melodymurray3289

7 жыл бұрын

route 49&61 clarksdale

should have used a mojac to raise the mower..a hell of a lot easier..

thanks for posting - just subscribed and liked - again thanks for posting ;)

Not everyone has an impact tool, if you work with mowers chances are you have no portable impact on the job, so hand tools it is.

how often blades need to be sharp

@royhoco5748

8 жыл бұрын

+Saul Pineda everytime they get dull

@bigcrookeddick5688

6 жыл бұрын

Saul Pineda every other day

jesus - great bucket compression test ....call your lawyer and make sure when you are crushed you can blame it on somebody

High High

ROFFLOL. I luv it.

Very Dangerous! Please don't try this at home...

Anyone that uses a torque wrench as a ratchet wrench to Loosen anything knows NOTHING about tools. You should not be showing anyone anything.

Definitely not how you do this. You need to drop the deck down and remove it. Then flip it over to access the blades. No way in hell im getting under this thing with a plastic bucket holding it up. I’m surprised you are even using a torque wrench as many corners you cut

Why not drop the deck pull it out flip it over and use blocks of wood to hold the blades? A lot safer than doing it the way you did it.

@thomas68morse

5 жыл бұрын

Now the deck needs re leveled. Stupid.

@MostlySunny2010

2 жыл бұрын

Because it's heavy as hell and a struggle to get it back on!

>doesn't chawk wheel >uses a bucket on one side rather than stands >jacks mower by deck rather than frame >uses tq wrench to loosen bolt rather than breaker bar or impact. Yeah. Not taking advice from this fool.

@QuentinCarter1975

3 жыл бұрын

I’d bet he knows how to spell chock though!

Sorry I has to stop watching this! No jacks and using a torque wrench to remove the bolt...YIKES GO BUY SOME DAMN JACK STANDS AND A REAL RATCHET!!