Had damp and mouldy smell in my launge for years. After a lot of replacing plaster and keeping a window open all through winter months, I decided to rip up the floor boards. My DPC was old-fashioned slates. Broken and missing motar from joints and some of the slates had deteriorated. Thorough cleaning, then replaced broken and deteriorated slates. Repointed, then cleared a whole lot of damp dirt from underneath the suspended flooring. Let the area dry out for approx 1 month. Yeah, it was a long, hard, and messy job, but it was worth it. Replastered wall. Replaced damp skirting and floorboards. Sanded and varnished wooden floor. Damp walls and smell gone. Oh, I also had to dig up the concrete paving under the windows outside as it was higher than the airbricks. I replaced the rotten makeshift airbricks covering with clay airbricks. My launge has remained damp free and smells great for over 3yrs now. And i'm a woman in her 50s! I learnt almost all I know from these DIY videos. My thing is, have a go. You never know what you can achieve. The best thing is, you save yourself a fortune.

I had a cold wall in my wardrobe. Love their products used the damp proof paste and heat reflective wallpaper.

@spendtimesavemoneydiy

Жыл бұрын

Their products really impress me 👍🏼

Has it dealt with the symptoms, what about the cause. The damp will still be there behind it. I spoke with someone who did this and damp reappeared further up 4 or 5 years later. Hope it works for you.

Well explained and demonstrated, thanks. Made things a lot clearer.

This is the first video of yours that I've seen and honestly I think it immediately became my favorite DIY video. You took the mistery out of a fairly intransigent ubiquitous problem and explained everything perfectly. A fantastically helpful video, well done mate! Thanks very much.

@spendtimesavemoneydiy

11 ай бұрын

Your favourite diy video. Wow what a compliment. Just glad you found it useful 👍🏼

Damp will come through that plaster I promise you, there is no special coating to stop the damp, the coating will just peel and bubble off. In an old house (mine is 250 years old), the only sure way is to take out a section of the wall at floor level say 4 bricks length at time at ground level either one brick or two bricks thick, then with the hole clearance available dig out as much below ground which was under the bricks you have taken out, a breaker drill will do the job beautifully especially if you can break up the adjacent floor say 3 inches out and that will enable you to sideways dig out the old damp foundation rubble causing the rising damp. Having dug out your new foundation trench you have , now you have to put in there what you would use as if was a new house you were building, ie impervious materials, quality concrete, DPC and blue clay impervious bricks. This might sound like hard work but it's worth it. The best thing is that the layer you put in say 2 bricks high when dried off, will be totally dry and the damp brickwork above it will dry out at about an inch or 2 a month, even quicker if you want to use a fan on the wall continuously. A 4 brick section of the wall taken out at a time and it won't take long and in the end you know it's been done right and any plastering done above that new brickwork you know it will be good and dry.

@shereeclinton8741

22 күн бұрын

It's not meant to stop it. The rods do.

Nice job, can tell you take pride In your work, tidy.

Excellent product. Explained well

Dude, fantastic video. I had 2 professionals cone and do my external wall, took them 3 days and the damp came back. Gonna send them your link.

@shereeclinton8741

22 күн бұрын

Lol that's why I'm determine to do it myself.

Absolutely brilliant video. Excellent explanation all thro.

My guess would be gypsum plaster sealing-in the moisture causing the build-up of the wet. Solution: Remove all the gypsum plaster and replace with an appropriate BREATHABLE plaster and problem solved. It's amazing that people do things and are completely oblivious to what is actually going on around them.

@BrainFizz

8 ай бұрын

This!!!! NHL 3.5, and check the exterior ground level, and guttering too!

@gauravjadhav3643

5 ай бұрын

Exactly 💯

Cool video la, finished product looks boss

You are just awesome. Can we use it on the outside wall please. Thanks so much for your presentation

great video mate 🤙

Trying the dryzone rods tomorrow. How amazing is this technology?

Grand job that m8! 👌

Thank you. Very useful

Great video!! thanks

@spendtimesavemoneydiy

Жыл бұрын

Glad you liked it! 👍🏼

Thanks, amazing!

Cracking job mate...your trowel skills are very good

@spendtimesavemoneydiy

Жыл бұрын

Thank you, plastering sort of came naturally to me 👍🏼

@janegoodwin379

Жыл бұрын

Brilliant tutorial considering not a plasterer by trade a fantastic job, u make it look so easy, I'm in the process of house buying & just found out from my survey it looks like it's got some rising damp on the outside wall, just haven't a clue what to do now knowing this 😞 not sure i want to commit to it now, the surveyor has marked it rating 2) ( orange ) & not 3) red thank God, but looks like it still needs addressing 🤔 great video though

Thank you!

@spendtimesavemoneydiy

Жыл бұрын

You're welcome. Hope my video helps you with your rising damp. Thanks for watching and please consider subscribing 👍🏼

amazing

very impressive plastering how much experience you have with that? might have to hire.a plasterer to do that part, but would love to try myself ha

Ive been told the best way to deal with chimney salts is to knock all the render off, then spray it with TG500 and use Sika 1 in the mix. Is this right for chimney salts?

How many bags of their plaster did you need to do the size you did? I am doing exactly the same width but up to 1.8m, so plan to buy double the amount you used. Thank you for this video and for your answer in advance!

Great job, be proud of your work 👍

@spendtimesavemoneydiy

Жыл бұрын

Thank you, nice comment. I should be more proud of my work but I'm my own worst critic 😂

Thanks!

@spendtimesavemoneydiy

Жыл бұрын

You're welcome. Thanks for watching and please consider subscribing 👍🏼

I have this kind of problem, how much would you be liking at someone to do this for you? I’ve seen the dry rods for like 10 are about £25. Before Labour and other materials

Great job and well explained thank you 😅

plug socket conveniently located away from the rising damp area lol. nice.

@spendtimesavemoneydiy

Жыл бұрын

Just lucky with that one I guess

Wish they did similar products for garages. I have a huge problem with water seeping through an underground wall. You're a brave man to take on plastering as a non professional. The tiniest imperfections are magnified once you get silk paint on there.

@spendtimesavemoneydiy

Жыл бұрын

They do tanking products that would do a garage. I'm quite good at plastering, it sort of came naturally to me without being taught but I only use matt paint 👍🏼

@matbroomfield

Жыл бұрын

@@spendtimesavemoneydiy What's a tanking product? Is that the word I should search by? Yeah, matt paint hides a lot of sins but I do like the sheen of silk. Just give sa wall a bit of life without it being OTT.

@spendtimesavemoneydiy

Жыл бұрын

@@matbroomfield tanking is for walls with ground levels above the dpc so the likes of basements

@matbroomfield

Жыл бұрын

@@spendtimesavemoneydiy I'm sorry - what's the dpc? Can I use tanking on floors? Can it be painted?

@spendtimesavemoneydiy

Жыл бұрын

@@matbroomfield dpc = damp proof course usually 150mm above ground level. The tanking is for the walls and you can use a damp proof membrane on the floor like I did in my garage. Here's a link to the video Damp proofing the garage/workshop floor and new osb flooring kzread.info/dash/bejne/nWp5m5aoZpbPcaw.html

I had this but I Checked behind skirting board and it was dry. The issue wasn’t rising damp but simply condensation from the cold wall as it’s solid. Ventilation was the solution so not necessary to drill loads of holes into brickwork.

superb

can you use this method with breeze blocks

Thanks for the detailed installation I am going to use the product next few days 👍

Amazing this mate, wanted to ask does the other side need plastering as it’s an internal wall?

@spendtimesavemoneydiy

11 ай бұрын

If it's affected by the damp then it will need re-plastering. Thanks for watching and if you'd like to subscribe to my channel that would be great 👍🏼

Hi good evening can you tell me what are this white thing in the wall is the candles

Did you do the same on the other side of the wall?

👍👍👍Thanks

@spendtimesavemoneydiy

Жыл бұрын

You're welcome 👍🏼

Brickwork looked bone dusty dry!? Yet surface of gysum plaster appeared damp. Doesn't seem like the problem was from behind the plaster. Was a damp survey done first? Looks like you've just hidden the real problem for a few years. Hope the floor scrubbed up well after too. A few more dust sheets down would have saved you hours of cleaning up.

Only needed lime plaster and breathable paint

Can you do it from the outside if the wall has an external face

very good video ! if you was plasterboarding after the dryzone rods what salt neutraliser would you use on the wall ? thankyou

@lyndonmather3321

Жыл бұрын

Hi mark watch other video dry zone similar but they use 4 X3 plasterboards nearly same method so put in express system (dry zone)an also Google damp Sam express system I was using aqua boards but to be honest when I saw damp Sam an dry zone using normal 4 X3 boards I've changed to them hope this help pal 👍👍👍saves u mixing up the renovating plaster which I don't like them google or phone dry zone up or go to the merchant off they have the products video was good to watch he was good but I prefer the other way using boards 👍👍👍👍

Am Michael from Ghana where can I get the product some

Wow and your not a plasterer wish I could do as good. Great video

@spendtimesavemoneydiy

Ай бұрын

You might be good at plastering, you never know unless you have a go 👍🏼

I’ve got an 1850s house and an old skirting board has rotted on an internal wall. I’ve not taken it off yet, but it has to be rising damp. Have watched loads of your other videos for brilliant advice and going to give this a whirl!

@spendtimesavemoneydiy

Жыл бұрын

Let me know how you get on 👍🏼

@peterfriel5129

11 ай бұрын

www.youtube.com/@WarmDryHome

@whiterabbit1632

6 ай бұрын

rising damp does not exist: scammers like this do! AVOID

@hindleymanb6626

5 ай бұрын

​@whiterabbit1632 if rising damp doesn't exist what is that on his wall at start of the video

Really helpful video, thankyou! And you did a great job on that plastering!

@spendtimesavemoneydiy

Жыл бұрын

Glad you found it helpful! I'm just a DIYer at plastering but I did pick it up quickly. Thanks for watching and please consider subscribing 👍🏼

Recently had a quote for £1056 to do less than a meter of rising damp. No way i'm paying that. Thank you so much for this video. I think i will now do it myself 👌

If we have on the first floor from the ground mould and the same wall in the next room on the second floor from the bottom. So how to work on the second floor? Where does the water go, if we do Similar ways? Does water not go to the first floor from the top? how to fix that wall on the first and second floor?

Great stuff. Did you manage find out teh cause of the rsing damp? If so, how did you fix it so it doesnt occure again?

@czx68

3 ай бұрын

How did he fix it? With dry rods of course, did you not watch the video?

@jonneymendoza

3 ай бұрын

@@czx68 no, what was the cause of it

@adrienne7513

2 ай бұрын

@@jonneymendoza Gypsum plaster layer placed over the old breathable lime plaster is locking moisture in - just remove the gypsum and problem is rectified, Everything he did in this video is nonsense.

@jonneymendoza

2 ай бұрын

@@adrienne7513 would plaster board drywall be better for preventing damp?

You did a nice job. Be interesting to find out why that wall was getting damp, must be some water source underneath there.

@spendtimesavemoneydiy

Жыл бұрын

The house is 90 years old so I think whatever damp proof course they used if any is now failing so damp is beginning to rise in a few places

@slyteen2197

6 ай бұрын

The electric socket has been moved at some point and the affected area filled with bonding coat which is unsuitable for low levels where salts can be present. All that was needed was the affected area be chopped out and then patched with the dryzone express system or salt resistant render.

What about external side of wall?

Nooice!

@spendtimesavemoneydiy

Жыл бұрын

Glad you enjoyed it 👍🏼

whats rthe purpose of the rods >?

How much that cost to fix this labour and material

All you had to do was chop out the bonding coat and board using their express system. Bonding coat is not suitable for salt affected areas.

So what function do the rods serve? Do they wick the damp?

@spendtimesavemoneydiy

Жыл бұрын

They create a damp proof course in the brickwork. I probably should have said that in the video 🙈

Good video, but one thing I don’t get is what is the purpose of the rods? I don’t get it

Could you just dot and dab wall instead of plastering ?

Can you send me the link to buy all the materials for this job please. Many thanks

@spendtimesavemoneydiy

10 ай бұрын

The links should all be in the video description 👍🏼

This is very helpful. Thank you 🙏🏼

@whiterabbit1632

6 ай бұрын

How is it helpful? He does not have a clue about old house! Have you heard of lime?

Is it possible to reuse the dryrod offcuts (for example put two in together)?

@spendtimesavemoneydiy

Жыл бұрын

Yes I think that would work fine 👍🏼

If you use the rods externally, what do you need to do to cover them up?

Thanks Mate - exactly what I was looking for. Saved me tons of time. Cheers.

What a fantastic video. Explanations' and methods demonstrated clearly. Well done and thank you, this has greatly helped with my next DIY project.

@spendtimesavemoneydiy

10 ай бұрын

So glad my video has helped you out 👍🏼

I think the 1st coat of plaster should be as instructions on bag-- because it needs to get in all the cracks and crevasses to seal the brickwork better-- then yes make it slightly thicker for 2nd coat . good job well done and thanks for sharing.

Is the skirting board new? If not why not remove the skirting board first to see what is happening behind the skirting board first?

@spendtimesavemoneydiy

Жыл бұрын

It could've only been rising damp. There weren't any other sources of moisture that could have affected that wall. And when I drilled the mortar it was very damp so it was the whole wall not just that area.

I have a terrace house, at what height does tbis need to be injected, as i have solid oak wood nailed to the floor.

@BryanNeill-yg5db

6 ай бұрын

Have you any evidence of your rising damp? I advise you to not inject your walls.. such a heavy work that breaks your home. Do you know other solutions to fix it?

@nick2207

6 ай бұрын

@@BryanNeill-yg5db no I don't what can you suggest

@BryanNeill-yg5db

6 ай бұрын

@@nick2207 A friend of mine has used a DIY solution, an electromagnetic polarity inverter, which seems pretty recent in UK. It worked very very well, he was diagnosed by them on the phone. The company he worked with was BFL I think. Never heard of it?

have someone tried ? does it help for the water not to come anymore from the floor ?

@paulp3497

10 ай бұрын

Yes it does good stuff .but no need to plaster the wall.just use plaster bord

More silliness

It could be bridged somewhere

@jonneymendoza

Жыл бұрын

Yes hard to tell without seeing the other side of that wall

Just two points. 1. If you have to remove the plaster back to brick on a solid 9” wall anyway. Don’t waste money on an injection system, just get it plastered in lime. NHL3.5 will do the job, and dry in a similar tins to gypsum (which is trapping your moisture inside the bricks. 2. Rising damp doesn’t exist. Water travels down, either your ground level outside is too high (dig it out and lower it), idd red your gutter is overflowing.

@spendtimesavemoneydiy

8 ай бұрын

But it is an internal wall, both sides are in my house, one side in living room and the other in the hall with no water or pipes anywhere near. The mortar behind the skirting boards was like damp soil and smelt like damp soil. A lot of people have said rising damp doesn't exist so why does every new building require a dpm and dpc?? I'm no expert that's why I sought advice from safeguard.

@BrainFizz

8 ай бұрын

@@spendtimesavemoneydiy old builds had dpc too. Probably made from slate. Are your floors still wooden on joists?

@spendtimesavemoneydiy

8 ай бұрын

@@BrainFizz I know old builds had slate dpc this is a 1930s house but I'm unsure what the dpc is or was but external walls are fine just the internals. The floors are all solid concrete

@BrainFizz

8 ай бұрын

@@spendtimesavemoneydiy there you go then, there’s your cause…. The modern floors have most likely. Bridged the original DPC on the internal walls and stopped the original airflow under the ground floor..

@spendtimesavemoneydiy

8 ай бұрын

@@BrainFizz but the floors are the original parquet, oak in living room and mahogany in hall

Always looks easy then when you start the first step, taking off the skirting, on a 30s planked floor house takes the jam right out of your doughnut. Nails rusted to the brick, skirting ends up as kinling and you can't buy that Suze and type anywhere on the planet so the whole room needs reskirted and the water table is so high under the floor that there's an inch of standing water. Let's get some real world problems. As you say anyone could fix that one.

This is something I’m going to have to do in the near future, you made that look so easy

How

@georgestanton660

Жыл бұрын

Nice job! Are you able to use this system with stone walls?

How many DIY’ers can actually apply render and can he be 100% certain that the mortar joint is totally sealed with the cream so where is the guarantee going to come from.

@jonneymendoza

Жыл бұрын

Yea this is not really a DIYer. If you can DIY this then you could do a hell of a lot then yourself!

@spendtimesavemoneydiy

Жыл бұрын

I am only a DIYer at this and plastering. The manufacturer gave me all the instructions to follow to make the video. And if I can DIY plaster I'm sure others can too if they have a go.

doesn't this just push the moisture somewhere else. you make a barrier to where it is coming through right now, but who knows where that moisture is going instead. I can't help but see this as a temporary thing. Usually pushing the problem down the road to the next owner of the house (first hand experience of this happening right now)

@aamo10

11 ай бұрын

I think it acts like a Damp proofing course with the rods then everything else sounds like over engineering it to make it fully sealed.

@jonp6798

9 ай бұрын

You might be right but it depends on the cause. The video doesn’t have enough information in it to explain the cause as it’s about this system. Internal non-party walls with a concrete floor can be a head scratcher.

@thecontinuedvoyage3746

17 күн бұрын

Had neighbour with damp who had it treated similarly to this. All that happened, was the damp came through into my house through the adjoining wall. After they moved, the new neighbour removed an old extension only to find an old blocked drain. I cleaned and made good and the damp slowly dried over time!. This stuff just costs money and doesn't solve the issue just masks it

@johnmajor5525

13 күн бұрын

Papering over the cracks, treat the source not the symptoms

Can’t beat old school sand and cement if done correctly…this is basically a advertisement campaign…

And surprise surprise the brickwork seems bone dry..

@spendtimesavemoneydiy

Жыл бұрын

The mortar was saturated

@anthonymclean9743

Жыл бұрын

@@spendtimesavemoneydiy Didn't look like it with the dust from the drilling.

@spendtimesavemoneydiy

Жыл бұрын

@@anthonymclean9743 it was like wet soil and it smelt like wet soil too

@abertoon

Жыл бұрын

​@@spendtimesavemoneydiy I've had a similar issue, internal wall, absolutely no way of water getting in apart from the ground allegedly. Spent years and lots of money (including a system like the one in this video), professional opinions - couldn't resolve it, until I installed a new ventilation system. Now moisture is low in the house and the issue has disappeared despite high rainfall. Likely same thing happening here... those bricks look dry similar to ours, even if the mortar is saturated, doesn't mean it's coming from rising damp, likely the moisture pooling on that wall is seeping into there. The wall closer to the ground in certain spots is colder, temperature may well be affected by groundwater underneath house but not rising damp in the way a lot of people make out. Definitely not worth removing plaster / pumping in chemicals into your wall / replastering IMO. Cancel Reply

And yet you’ve done a hell of a lot better job at plastering than our council hired of cowboy contractors 🤦‍♀️😂 they skimmed our kitchen and bathroom walls terrible and the plaster may aswell be non existent 🤦‍♀️

How about this: " After damp-course installation, it is very important that the treated walls are left to dry for a period of several months before any re-plastering / re-rendering, painting.... Generally, it may take about a minimum 3 months of drying before any re-plastering/re-rendering can be done. Very salty walls should be left to dry for a minimum 6 months..."

@Chiknnuggitbuzfeed

10 ай бұрын

Or just use a dehumidifier to speed up the process.

@winstonsmith3690

9 ай бұрын

What if it's going to be boarded?

@just4bantzlel33

8 ай бұрын

​@@ChiknnuggitbuzfeedI thought that would make cracking more likely

@Chiknnuggitbuzfeed

8 ай бұрын

@@just4bantzlel33 i guess you're right about that.

Didnt really get what those plastic /rubber tubes were all about?

@spendtimesavemoneydiy

11 ай бұрын

They contain a chemical that filters into the mortar to create a barrier. Thanks for watching and if you'd like to subscribe to my channel that would be great 👍🏼

My guess is the rad on the lefthand side😂

@spendtimesavemoneydiy

8 ай бұрын

Guess again, I fitted that radiator and the pipes go the opposite way 🤷🏻‍♂️

It’s a decent system but Sika also do an impregnating compound the appropriate holes are filled with the use of an ordinary caulking gun. A little bit of advice when using SBR as a bonding/sealing coat, damp the substrate firstly. The SBR is more easily absorbed into the substrate. Unfortunately gypsum is very water soluble, very. Better to use a lime based render as it’s also breathable.

doing a job and not protecting the wooden floor , wtf

@spendtimesavemoneydiy

Жыл бұрын

The floor needs restoring anyway

Non of this is needed!!! You said it’s a solid wall…..you have modern materials that do but allow moisture to escape! What you have is condensation which is exactly what they call rising damp ……it doesn’t exist! If you had taken the plaster off and let it dry out that’s it plus a lime plaster afterwards No idea if you have cement render on outside but if you do this is further more your issue as cement and gypsum trap moisture!

This sorry excuse for a human is selling you snake oil! He does not have a clue about damp! AVOID AT ALL COSTS

Nope.

This is not DIY

@hayley_michelle21

Жыл бұрын

If it’s not DIY what is it?

@samanmudannayaka9604

Жыл бұрын

@@hayley_michelle21 this is a full on builder job. I was expecting a small plastering job I could do with my simple tools.

@hayley_michelle21

Жыл бұрын

@@samanmudannayaka9604 yeah he’s a furniture maker not a builder and he did it himself hence DIY

@samanmudannayaka9604

Жыл бұрын

@@hayley_michelle21 ok

Total rubbish.!! The damp is obviously being caused by the gypsum plaster layer that has been placed over the old original lime plaster. The lime allows moisture to breath out of the wall - the gypsum was locking it in. All that is needed here is for the gypsum layer to be removed or all taken down and the lime reinstated. Everything you did here is utterly pointless and has made the situation much worse. That wall will be saturated behind all that waterproofing in a few years.

Why is the damp in just one small area? What investigation was done? What actual cure did you achieve? You appear to have just covered it over and not got rid of the root cause. Smoke and mirrors.