Professional commercial painter here , don’t walk with the paint , go an armspan and come back then move onto the other section , comes out slicker

@n54anaya79

3 жыл бұрын

Okay thank you, will definitely try that

@mrhomegrow

3 жыл бұрын

Good tip, thank you

@royjones9852

2 жыл бұрын

Hello just got an aftermarket bumper cover for 2010 camary Le. Manufacturer says primered. So skip the primer and start with a few light coats of adhesion promoter? I know nothing about paint. Thank you Roy

@tonyg-2jz82

2 жыл бұрын

This comment is way too under-rated! I've learned the hard way but this is an absolutely priceless piece of advice. That and starting and ending the spray stroke before and then off the part you're painting, never starting directly on the piece you're painting. Ie start spraying a couple inches to the left of the bumper and finish your spray am inch or so off to keep the spray nice and uniform.

@tonyg-2jz82

2 жыл бұрын

@@royjones9852 Get a grey scotch Brite pad and scuff it up then use an 800 then 1500 sandpaper and wet sand that primer down to smooth it all out. Then use adhesion promoter followed by paint and clear coat and make sure to wait the recommended times between coats. I'd wait 24 hours before clear coating also but that's just me.

You can use cheap white primer before applying the relatively expensive base coat over a dark primer to cut down the the required coats needed to cover over grey primer.

@kennyh5083

Жыл бұрын

Yea cheap primer now there's a great tip, cheap-out on the primer so it can all flake fall off in no time! What a great tip!

@SupeDefy

Жыл бұрын

Yup. Color matching primer would make the base coat go down easier. But not much lost on this guy since he is using $10 DupliColor can. :D

great job,now it gives me an idea how to paint my bumper.

Thanks man. You made that easy to learn and do. Great work!

Fantastic job, what a difference once all completed, has helped me with my own spray painting on my rear bumper and boot lid, from Edward Scott in Queensland, Australia.

I will definitely go this route. Good video bro.

Thanks for the video! I'm going to plastic weld a hole in my bumper and respray and hope it turns out like this haha

This was handy painting my grille on my 99 Burban. Thanks for the video.

@n54anaya79

2 жыл бұрын

No problem

I am gonna paint a front lip and side skirts for my rsx, this helped a lot thanks man!

Good job. Cheaper then a shop same results.

Nice, good job, I will be doing mine indoors tho with spray guns not cans. But I will be using cans for the adhesion promoter ;) thanks, good job!

Make sure to shake the hell out of the 2k gloss can and the clear coat coming out the can will be amazing

Bomb results 👍

That's an amazing job. Can you please share the details like how many cans of primer, base coat and clear coat were used and also how many ml.

Looks great for an outdoors painting. Great work! Going to give this a try with melbourne red on an F30 MTech bumper. 🤞

@Daniel-jk9ge

3 жыл бұрын

How did it go

@southbayengineered6905

3 жыл бұрын

im painting my f10 550i imperial blue mtech bumper tomorrow !

@yup-2067

3 жыл бұрын

@@southbayengineered6905 i wanna see that

@southbayengineered6905

3 жыл бұрын

@@yup-2067 it went well! Worked out great

@yup-2067

3 жыл бұрын

@@southbayengineered6905 did u post or can you post it. Sounds dope asf

Good all around vid....helped a lot thanks!

Nice results 👌

Looks good.

You made this look so easy

@GABRIELRIVERO_02

3 жыл бұрын

I\'m not sure but ,if anyone else needs to find out about car spray painting tips try Sovallo Auto Painting Fixer (just google it ) ? Ive heard some interesting things about it and my work buddy got great success with it.

How long should you wait before wet sanding?

Nice job!

great job

Looks great

Nice job. So u bypassed scuffing and sanding because it came pre primed? I’m painting a bumper that’s pre primed. So would just cleaning it , then laying adhesion promoter, base and clear be correct?

Very informative thanks, how many cans of primer, paint and gloss needed for a full plastic bumper

It's somewhat recommended to paint indoors, only to mitigate dirt and debris from blowing and falling onto the paint. For other comments, from experience, base coats usually stop being tacky after 20-30 minutes, and clear coats usually harden after 45 minutes to an our unless with a breeze or wind, which will probably bring it down to 30 minutes.. I think a rule of 3s is good to start with. 3 coats of paint, 3 coats of clear coat. You need to wait for your paint to dry before sanding as it may still be mushy, and any grit will imbed easier into soft paint. I think having your piece elevated to around chest-height, or having the top of it at just under your chin makes it easier to paint, find a way to hang the piece with metal coat hangers from spots that won't be seen.

@jdmchickkustomz9417

10 ай бұрын

What if you get dirt in the clear coat? How do I bluff and sand the bumper cover? I painted mine outside too with my gun and professional paint but it got dirt in it. 😢

@TheOnlyInformant

10 ай бұрын

@@jdmchickkustomz9417 you'll have to sand it down over a large area after it hardens and respray. Very frustrating. You might have luck with lacquer thinner in a spray gun. You'll need to be quick because it will make the paint coat mushy. The only direct route is sanding that spot down and using Bondo and respraying with primer, paint coat, clear coat and fine-grit rubbing compound to smooth out the layering.

@jdmchickkustomz9417

10 ай бұрын

@@TheOnlyInformant sand with what grit?

@TheOnlyInformant

10 ай бұрын

@@jdmchickkustomz9417 you gotta remove a lot of material, might as well make quick work of it. Maybe 500 grit

Could that primer be used with different types of spray paints

Thank you 😊😃😀😃😃😀 I hope my is the same. First time trying it. 🤣😂😂😂😂😂

Does this last like if it were originally painted like car wash and winter like that?

All clear finishes will have some type of orange peel. I can see it on his finish. But i believe you're supposed to install the bumper and wait a week or so. Then you can wet sand with 2000 or 3000 grit and then buff it with buffing compound.

@n54anaya79

27 күн бұрын

Thats correct

I have a prime bumper that I need to paint jet black, but they say sand it with 800grit or higher to get it prep, so isn't it prep already to add on the adhersion promoter, thank you sir???

How many cans of each product did you need? Thanks

This is a good video. How many cans of paint did you need? How many cans of clearcoat? Seems like only 1 coat of adhesion promoter?

This was absolutely awesome, just wish you told how long you waited after every coating, and what was the watering step you were doing such as if it were to clean it

@lucifer-ry8tx

11 ай бұрын

15-30 mins. Says on most cans. You want it tacky still

I just got a bumper not to long ago im planing on painting it myself, this video really motivates me to do it myself instead of paying $600-$1000k... Id like to see an update on that bumper if possible bro

@n54anaya79

3 жыл бұрын

Yeah go for it, this was done for my friends car. He sold it earlier this year but the bumper was still looking really good

Hi bro you dont need use primer before paint ?

How many cans of base?

Great job

@n54anaya79

Жыл бұрын

Thank you

What if the part I got doesn’t have primer? Should I sand it and then prime it or just go for the primer?

Would this work if I’m using red paint ?

How many cans of paint does it take to repaint a bumper? Will a 12oz can of paint be enough?

I am about to do the same thing on my bumper, has it held up well ?????

Thanks for video 🙏🏻I need do my car too so for after market plastic bumper cover before apply primer ,dont u need sand it ? Just curious because I need help

@n54anaya79

5 жыл бұрын

crabbymrd Lee yeah it’s a good idea to scuff it down with a scuff pad

@muratsol2679

5 жыл бұрын

DIY Lifestyle thanks 👌

How many spray can did you use for 1 bumper?

What if you get dirt in the clearcoat? How do I sand n buff plastic?

So you dont have to sanddown the old paint?

How many cans of paint and clear coat did it take?

How cans of the base and clear di u use?

How many cans of white did you use

BUT, why you did not apply the Primer after the adhesive promotor??????????

Vinyl wrap or spray ?

Nice video I tried this today but with diamond graphite

@n54anaya79

2 жыл бұрын

Nice 👍 Glad it helped

@goldeng3541

2 жыл бұрын

@@n54anaya79 quick question how long do you wait to put it on the car after you’re done?

@n54anaya79

2 жыл бұрын

@@goldeng3541 i just let it dry overnight

How many cans of color and clear coat?

How many cans did you use in total?

How many cans of paint did you use ?

Used all three cans of each?

You should start off the bumper and finish past the bumper and hold your can more level

@jakekovacevic3435

3 жыл бұрын

@Donnie V. gives you a more even coat and doesn’t leave streaks and runs in the paint

did you have orange peel???

How many layers of the adhesion promoter did you do? And how long should you wait after that before the color coat?

@tonyg-2jz82

2 жыл бұрын

2 layers of adhesion promoter is fine. Wait an hour before using your base coat and then 10 minutes between 3-5 coats of base. I'd wait 24 hours before clear coating if possible and start with a lighter coat with 10 minute intervals going a little heavier each time. Then wait a hood 24 hours after that before wet sanding with say 1500,2000,2500 grit then buffing and finally polishing if you really wanna do it right.

@bluewanderer9903

2 жыл бұрын

@@tonyg-2jz82 Tony any advice on how to do it when changing the colour of the bumper. My car is blue/navy and new bumper and side skirts came from red car. It is a Modulo Voltage kit cant buy it new anymore so had to go for second hand, in great condition though no cracks nothing broken even red paint/lacquer is perfect on it. Any advice? Thanks

How long do we need to wait before applying the clear coat? And is washing it with water necessary?

@n54anaya79

5 жыл бұрын

Raihan Iqbal i would say atleast half an hour and no it’s not necessary

Did this, but failed. Forgot to dand and used a cheap clear coat then 2k. Wish I saw it earlier, like the simple steps you made for it.

Nice video so if I have a primed bumper do I still gotta use primer spray on a plastic bumper before I spray paint it black then clear coat it?

@n54anaya79

4 жыл бұрын

Kevin 215 Hey thanks, no if it’s already primed don’t prime it. Just wipe it down good & start painting it

@OperatorGhostShadow

4 жыл бұрын

DIY Lifestyle even if I’m doing black paint ? I’m using lacquer clear gloss as well

@n54anaya79

4 жыл бұрын

Kevin 215 yeah, so if it’s primed already just spray the black paint u have. Should be easier actually cause black covers faster & then just spray the clear

@OperatorGhostShadow

4 жыл бұрын

DIY Lifestyle thanks fam gonna attempt this now since I gotta better understanding 👌🏼

How many cans you use?

I always paint in flip flops myself

@chellobarnes7257

4 жыл бұрын

How do you handle little bubbles?

Good job bro I love it you use very short way please where I may get the exactly sprey ?

@n54anaya79

3 жыл бұрын

The 2k spray paint i found it on amazon. I’ll add the link in a few

@searinosearino

3 жыл бұрын

@@n54anaya79 thanks so much for your help

In your other video on painting a g35 bumper. If my bumper has already got color on it can I color over it or do I need to sand the color ?

@cristobalvillalpando9578

3 жыл бұрын

sand or the paint will chip

@satno4224

3 жыл бұрын

Sand and use primer

how much paint did you need to do this? was one can of each enough?

@Tortas0504

3 жыл бұрын

You need like 2

How many cans used?

What’s the process if going red to black?

What Nissan color is that? Need that

When I spray paint outside the wind seems to blow the paint away even when it isn't that windy, so I try to paint in my garage.

thanks this helped me a lot!

Shouldnt you scuff the bumper down first thing. And then wipe it down with a tack cloth and acetone? The mold process has a release agent. Really bad for paint jobs. Then definitely a primer. Will help the paint adhere better and lay your coats out much better. Hope helps

@itsmanoo3260

3 жыл бұрын

I was thinking the same thing. If uu don’t you will have flaws within the spray

@markangel2919

3 жыл бұрын

Nah you should be good 😌 some companies actually tell you don’t have to

@user-xx7pg3vw9k

3 жыл бұрын

Supposedly letting it hang out in the sun is good enough to let it dry out.

@nathanielbolden5053

2 жыл бұрын

Don't use acetone it will soak into raw plastic!...use 91% alcohol its water based

@brettdrt1

2 жыл бұрын

It's a pre primed bumper, no need to worry about mold release.

Do I use the adhesion promoter before I prime my bumber or do I prime first and then use the adhesion promoter

@albertandrade1394

4 жыл бұрын

Alfredo Magana adhesion promoter first

How do you know if your bumper is already primerd? I just ordered a brand new factory bumper for my e46 so I want to be safe before I proceed!

@n54anaya79

3 жыл бұрын

Cuddii it should state it on the place that you got it from, if not it’ll usually be a grayish color if it’s been primered and it’ll feel really smooth

@braydenoslo

3 жыл бұрын

@@n54anaya79 after you spray painted it, how long did you wait to wet it down and wet sand it?

Hi how many cans of base color did you use? And what size in oz can?

@n54anaya79

3 жыл бұрын

They were small cans forgot the OZ but i used 3

Whats the second step? Is that the sort of gloss to make it shine?

@malmansoori2384

3 жыл бұрын

Actually, the 1st is a primer. They use primer to prevent the bumper from rusting and then 2nd is the original color code from the factory.. The 3rd is clear coat it is like a protector for the color

Does the paint come off easily on Plastic compared to ABS??

@virus-hoax

2 жыл бұрын

Plastic is a generic term that incudes ABS and other types.

3 coats of that clear in a can is the equitant to 1 coat of clear coat out of a gallon I would have at least put 2 full cans of clear on that bumper. protect from rock chips a lot more

you are asking for (health) trouble using 2k clear with no respiratory gear however, its a drawback of the benefits of a 2k clear coat

@n54anaya79

4 жыл бұрын

eric mcnamara yeah you should always use a respirator, i was using a separate t shirt to cover myself alittle

What were the prices of all the cans ?

Just curious. Why not a primer after the adhesion coat and how many cans of color did this take? Awesome vid. Thanks!

@nukexD

3 жыл бұрын

Because the bumper was already “primered” from the manufacturer. I believe the adhesion just lets the paint stick better.

Hey what if you getting the little bubbles what then? Thanks

@n54anaya79

4 жыл бұрын

Chello Barnes you got them after spraying on the clearcoat?

Hey I'm planning on doing this same color and everything how many spray cans did you use and 2k clear?

@MyJamesMusic

3 жыл бұрын

Id reckon just get 2 bottles of each, shouldnt be too expensive, can always return the cans you didnt use

Do I have to use adhesion promotor on the primed plastic if it's already factory primed

@n54anaya79

4 жыл бұрын

amcon build no not necessarily

@Jasonaturton

4 жыл бұрын

So i can skip step one if its already primed black from the factory?

@Og_ChampChamp

4 жыл бұрын

amcon build i would clean whole part with alcohol before spraying paint tho

@Jasonaturton

4 жыл бұрын

Daniel Guzman clean it with alcohol, then wash it and dry it then start painting?

@n54anaya79

4 жыл бұрын

Jason Turton just clean it with alcohol

plastic primer??

Looks great! You didn't mention any safety gear. $20 for respirator (Highly Recommended to wear one) Goggles and Tyvek Suit $20 for both (For a small job like this these are optional, but it is better to be safe!) Also no mention about a wax and grease remover (Prep Solvent) wipe down before anything. If you're not using a sealer then forget about using it because some have very long flash times. I've made some videos to clarify these subjects.

@SupeDefy

Жыл бұрын

Looks like this guy was using a shirt as mask. I'm like dude, your lungs are worth a $20 respirator and your eyes are worth $5 goggle.

I saw your comment that it takes 2-3 cans depending on the color. Really for clarity, does that mean 2-3 cans for the base paint? How many cans do you need of clear coat? Etc Thank you

@n54anaya79

5 жыл бұрын

playray91 yes, 2-3 cans if you’re using the dupli color touch up paint since they are 8oz. If you are using another brand they will most likely be 12oz so you’ll only need 2. For the clearcoat 1 can will be enough

Hey bro can you link me or let me know what paint and clear you used?

@n54anaya79

5 жыл бұрын

EuphoricVisions USC SprayMax 2K Glamour High Gloss Aerosol Clear www.amazon.com/dp/B0082LJMC6/ref=cm_sw_r_cp_api_i_FPR6CbH16PTT7

@n54anaya79

5 жыл бұрын

For the base coat, you can use whatever. I would recommend using rust-oleum. It’s a good brand

@SulfiteEntertainment

5 жыл бұрын

DIY Lifestyle thanks, I was asking because I also have a g35, I'm attempting to paint the bumper and fender, it's also white. These results look great!

What's the name of the music? Thanks!

@sirikulsomsuwan

4 жыл бұрын

Zeberka Did you ever find out who produced the music?

Do you know from where we can buy these paintings stuff?

@mailjamesthomas

3 жыл бұрын

Any auto parts store.

any updates on how it's holding up? any flakes or cracks? also, how many cans of each did you end up using?

@sylvainguinepain5624

Жыл бұрын

I’m curious how many cans it takes myself. I’m hoping one is enough.

@spencermontgomery5254

Жыл бұрын

For that size bumper I get at least two cans of paint and could probably get by with just one canned of clear

Nice paint job. How many cans of white and clear coat you use to finish the job?

@n54anaya79

3 жыл бұрын

2 or 3 cans of white and 1 clearcoat

How many cans of the adhesion promoter?

@n54anaya79

5 жыл бұрын

1 is enough

Is that an infiniti bumper?

Was that one can of paint for the colour?

@n54anaya79

11 ай бұрын

I used 2 of them

But, you have painted the grilles ! You should have masked them... But, overall, good job.

How many cans of paint did you go through?

@ravilalla3340

2 жыл бұрын

He said the following on another question 2 cans of 12 oz and one can of clear coat

What store do I find these supplies?

@n54anaya79

5 жыл бұрын

o.g.- Reala your local Advanced auto parts or other car shop

hey tony G 2jz below, or get a piece of 220 grit move to a 442 then a 680 to a 681 then for kicks use a 772 and a 801 then just run the puppy walking to a 999 then a 5000K finish grit sand paper, professiuonal talker here I know what to do................................ The trick is to get used sand for the sanding cloth then the shit is cheaper. sometimes I make ky own sand. Start with Silica and go from there............ / / /