Check out the complete project here: circuitdigest.com/article/arduino-not-working-troubleshoot-tips-and-tricks-to-make-it-work
@edulinktutorprovider8 ай бұрын
I am facing a problem with my arduino uno. Unable to update any program. Board Led is not blinking it is in steady mode. It is not showing any error. If possible help me to solve out.
@mixme86558 ай бұрын
New subscriber sir always watching your videos ❤ many learnings
@letsplaygtaSA23 ай бұрын
thank u brother it worked after ur tips
@BituponBorah-ev5fw10 ай бұрын
Bro, I am connected gsm900a modul on this ch340g uno board, my for sending sms, my cunnection is good and cood are uploded the uno, after runing not recived any sms on my mobile phone, but serial monetor show sms sending
@Circuitdigest
10 ай бұрын
very hard to say where the problem is without properly debugging - have you checked if your SIM card has a SMS plan?
@user-cf9od3xt7m9 ай бұрын
Hello , I supplied supplied high current through the Dc jack and now the ON , RX, and TX leds are always on . I do not what to do ?
@Circuitdigest
9 ай бұрын
looks like you have burnt the driver chip - try replacing it and you should be good
@gaganraj135
5 ай бұрын
I have the same problem , can you pls tell where can I buy it and how to replace
@udayaningalep47383 ай бұрын
I have an arduino uno which i ordered just recently, and code was getting uploaded to it perfectly fine, but when i powered it, it did nothing; I tried both the USB port as well as the DC jack which is on the UNO, but no response. What could be the issue?
@Circuitdigest
3 ай бұрын
Most likely the code may not be proper. Just make sure the the board its self is ok, compile and upload the blink example and check.
@abhipanchal834310 ай бұрын
I cant able to upload code in my arduino i changed voltagw regulator and ATmega but still not able to upload the code the on light and L light is on. also the 5 volt arduino post shows 4.9 volt and the voltage regulator show 1150 insted of 1820 and.
@Circuitdigest
10 ай бұрын
What error are you getting? Are you able to find the board under device manager?
@shamsuzzamansohel4 ай бұрын
Sir, I have purchased a new arduino uno r3 dip and tried to connect my laptop but laptop not recognised it. When I plug USB cable to laptop no plug in sound. Arduino power led on and pin 13 led blink 1 sec intervals. Is my Arduino damage?
@Circuitdigest
4 ай бұрын
Install the proper driver for the USB to UART converter.
@user-of6zx5gl2t11 ай бұрын
Avrdude Program not responding bhai ye error a raha hai 😢
@drmahesh19738 ай бұрын
bro plz help me i facing a problem my ardiuno board has 3 red inbuilt led light on after it got sparked i am pressing reset button but it is not blinking
@namangarg6959
8 ай бұрын
It's gone buy a new one
@pierpa_76pierpaolo8 ай бұрын
An Arduino clone doesn't work for me either. I did it this way (but I still have to test it): desolder the little button and two pieces of wire connect the pins (where the button was soldered) and bridge with RESET and gnd !!! It will work. Let me know. :)
@nikhilsurelia7563 ай бұрын
i have an Arduino uno R3(not clone ch340 driver didnt work) board which turns on the led is blinking from the start tried all the things turns out i do think it might be bootloader issue but not sure also it is not being detected in the com port section of the device manager Again the arduino turns on the led is blinking but no detection in the pc. Please help!!!
@Circuitdigest
3 ай бұрын
If it is not showing in device manager either the proper driver is not installed or the USB to UART converter chip is not working.
@nikhilsurelia756
3 ай бұрын
@@Circuitdigest Thank you, So i also installed the ch430 driver it showed it is installed and it is preinstalled for just checking if that works and it didnt, also any way we can fix the usb to uart converter chip? I will still try to check if any of the drivers work by reinstalling.
@tawsifchowdhuryaraf88668 ай бұрын
I am having a problem. When i connect the board TX, RX, L and ON all of these lights are on and IDE says not connected. I pre installed CH340 driver still no ports are showing. Please give me a solution.
@Circuitdigest
8 ай бұрын
most likely your driver IC is damaged, is your the ch3040 version?
@tawsifchowdhuryaraf8866
8 ай бұрын
@@Circuitdigest recently i used l293d motor shield after that this this happened
@Circuitdigest
8 ай бұрын
@@tawsifchowdhuryaraf8866 it could be that you tried to draw more current from the UNO board and thus damaged the voltage regulator. Use a multimeter to check your 5V and 3.3V pins on uno are giving the right output voltages
@amitsinhapune11 ай бұрын
hi, my code isn't getting reset after pressing the red reset button. I've tried a lot but haven't been able to. Please help
@Circuitdigest
11 ай бұрын
that's strange, how do you know that your code is not getting reset? are you able to upload code normally ?
@amitsinhapune
11 ай бұрын
like i put a blinking code, it runs. I press the reset button and after the blinking it starts running again. I'm buying a new one so no worries I guess.@@Circuitdigest
@Circuitdigest
11 ай бұрын
@@amitsinhapune cool, but i still dont see any problem with the way you describe your boards working
@geojunior7428Ай бұрын
my arduino "ON" LED blinks only once when i am plugging in. can i fix it?
@Circuitdigest
Ай бұрын
The ON LED is connected to the 5V line though a resistor. Check 5V line make sure there are no shorts and the 5V is present.
@ashifeakbal32086 ай бұрын
My arduino works when the USB cable is connected to the laptop but when I remove the USB to connect another power supply my program does not work. Please suggest what should i do?
@Yogesh62
5 ай бұрын
Same problem bro
@vighneshsomoshi99353 ай бұрын
My arduino for some reason constantly gives high output to digital pwm pin 3. Can you please tell what could be the problem? 🙏🏻
@Circuitdigest
3 ай бұрын
If a pin is always in the same state regardless of the code, then post probably the pins is damaged.
@technicalsubham2818 Жыл бұрын
Bhai Mera exit 1 status error dikha rha he upload nhi ho rha he plz help kya Karu me 😢
@Circuitdigest
Жыл бұрын
is it coming during compilation or uploading?
@NovaGamingNexus18
9 ай бұрын
uploding@@Circuitdigest
@selvagamingtamil10 ай бұрын
Light no not working 😢
@tuhinguha434 Жыл бұрын
Bro please help me com port not showing when I attach my UNO board with laptop. I've done everything I possibly can. CH340 driver is pre installed. I replaced my USB A-B cable. Still no ports or other devices showing in device manager. I've reset the Arduino board and my laptop as well. Nothing works. Please help!!!🙏🏻
@Circuitdigest
Жыл бұрын
try changing the bootloader
@tuhinguha434
Жыл бұрын
@@Circuitdigest Do I have to burn the bootloader by another Arduino board?
@04j6uday410 ай бұрын
After uploading code .the aurdino getting connected and disconnected and again connected and disconnected
@Circuitdigest
10 ай бұрын
Sounds like a hardware problem, My guess is that you have connected some motor or sensor which is consuming a lot of current forcing the Arduino to shut down and power on again. Remove all your hardware connections and try again
@fa36184
8 ай бұрын
Just like mine
@dhruvdodiya18148 ай бұрын
My arduino only run one program, i change with onther program but not working . I also reset it but still run first program. What should i do?
@Circuitdigest
8 ай бұрын
this is strange - are you able to upload the new program successfully?
@thelegendarygamers1272
8 ай бұрын
I am also facing the same problem
@Circuitdigest
8 ай бұрын
@@thelegendarygamers1272 i remember having a problem like that - the reason was a fast loop in my code, try pressing the reset button on Arduino and releasing it just before your code starts uploading
@thelegendarygamers1272
8 ай бұрын
@@Circuitdigest I have tried that but it did not have any effect on it. I installed the legacy Arduino IDE and there it showed me this error avrdude: verification error, first mismatch at byte 0x0000 0x62 != 0x0c avrdude: verification error; content mismatch On the newer IDE, I am not getting any sort of error. The sketch uploads without any sort of error on the newer IDE but it doesn't have any effect on the Arduino and it keeps running the same old sketch.
@KayXamTutorials
4 ай бұрын
This is exactly my same problem with Arduino Leonardo @@thelegendarygamers1272
@leeroyfernandes289Ай бұрын
My arduino is working but when I connect sonsers it is not working 😵💫😵💫
@Circuitdigest
Ай бұрын
Without a little more context we can't help you. Please use our forum to get more help.circuitdigest.com/forums
@rex_rubus3 ай бұрын
I have a Arduino pro micro and successfully build a volume control with 3 touch button(ttp223), but there is a problem pro micro often got disconnect not fully (like light glow when i touch the sensor but no light on rgb ring and volume knob also don't work)automatically i don't know why and every time i need to replug it to pc and make it work, do you how to fix it link from where i made it kzread.info/dash/bejne/lIGD17mbc9bNgKw.html
@Circuitdigest
3 ай бұрын
Make sure the Arduino is not stuck in some loop. Check your code.
@baklolgamer4436 Жыл бұрын
Bro can u help me
@Circuitdigest
Жыл бұрын
hi there, can you kindly tell us what problems you are facing?
@karthiuthay260710 ай бұрын
mine never worked in class
@Circuitdigest
10 ай бұрын
Actually learning starts when something stops working
@Pixelpulse_gaming017 ай бұрын
You help me
@Circuitdigest
7 ай бұрын
do you need help?
@Pixelpulse_gaming01
7 ай бұрын
Yes
@Circuitdigest
7 ай бұрын
how can i help you?@@Pixelpulse_gaming01
@logankieffer76967 ай бұрын
king
@Everythingvideos12 Жыл бұрын
Hello
@Circuitdigest
Жыл бұрын
hi there, how can i help you?
@Everythingvideos12
Жыл бұрын
I was working with the Arduino and I accidentally followed the wrong circuit then smoke came out of the voltage regulator. I don't have a soldering iron
@korfrm Жыл бұрын
короче я тебе на видио споливкой которое было годь назад ответь на комент пжжпжпжпжпжпжпжпжжпжпжпжпжпжжпжпжпжпжпжжпжпжпжпжпжжпжпжпжпжжп
Пікірлер: 71
Check out the complete project here: circuitdigest.com/article/arduino-not-working-troubleshoot-tips-and-tricks-to-make-it-work
I am facing a problem with my arduino uno. Unable to update any program. Board Led is not blinking it is in steady mode. It is not showing any error. If possible help me to solve out.
New subscriber sir always watching your videos ❤ many learnings
thank u brother it worked after ur tips
Bro, I am connected gsm900a modul on this ch340g uno board, my for sending sms, my cunnection is good and cood are uploded the uno, after runing not recived any sms on my mobile phone, but serial monetor show sms sending
@Circuitdigest
10 ай бұрын
very hard to say where the problem is without properly debugging - have you checked if your SIM card has a SMS plan?
Hello , I supplied supplied high current through the Dc jack and now the ON , RX, and TX leds are always on . I do not what to do ?
@Circuitdigest
9 ай бұрын
looks like you have burnt the driver chip - try replacing it and you should be good
@gaganraj135
5 ай бұрын
I have the same problem , can you pls tell where can I buy it and how to replace
I have an arduino uno which i ordered just recently, and code was getting uploaded to it perfectly fine, but when i powered it, it did nothing; I tried both the USB port as well as the DC jack which is on the UNO, but no response. What could be the issue?
@Circuitdigest
3 ай бұрын
Most likely the code may not be proper. Just make sure the the board its self is ok, compile and upload the blink example and check.
I cant able to upload code in my arduino i changed voltagw regulator and ATmega but still not able to upload the code the on light and L light is on. also the 5 volt arduino post shows 4.9 volt and the voltage regulator show 1150 insted of 1820 and.
@Circuitdigest
10 ай бұрын
What error are you getting? Are you able to find the board under device manager?
Sir, I have purchased a new arduino uno r3 dip and tried to connect my laptop but laptop not recognised it. When I plug USB cable to laptop no plug in sound. Arduino power led on and pin 13 led blink 1 sec intervals. Is my Arduino damage?
@Circuitdigest
4 ай бұрын
Install the proper driver for the USB to UART converter.
Avrdude Program not responding bhai ye error a raha hai 😢
bro plz help me i facing a problem my ardiuno board has 3 red inbuilt led light on after it got sparked i am pressing reset button but it is not blinking
@namangarg6959
8 ай бұрын
It's gone buy a new one
An Arduino clone doesn't work for me either. I did it this way (but I still have to test it): desolder the little button and two pieces of wire connect the pins (where the button was soldered) and bridge with RESET and gnd !!! It will work. Let me know. :)
i have an Arduino uno R3(not clone ch340 driver didnt work) board which turns on the led is blinking from the start tried all the things turns out i do think it might be bootloader issue but not sure also it is not being detected in the com port section of the device manager Again the arduino turns on the led is blinking but no detection in the pc. Please help!!!
@Circuitdigest
3 ай бұрын
If it is not showing in device manager either the proper driver is not installed or the USB to UART converter chip is not working.
@nikhilsurelia756
3 ай бұрын
@@Circuitdigest Thank you, So i also installed the ch430 driver it showed it is installed and it is preinstalled for just checking if that works and it didnt, also any way we can fix the usb to uart converter chip? I will still try to check if any of the drivers work by reinstalling.
I am having a problem. When i connect the board TX, RX, L and ON all of these lights are on and IDE says not connected. I pre installed CH340 driver still no ports are showing. Please give me a solution.
@Circuitdigest
8 ай бұрын
most likely your driver IC is damaged, is your the ch3040 version?
@tawsifchowdhuryaraf8866
8 ай бұрын
@@Circuitdigest recently i used l293d motor shield after that this this happened
@Circuitdigest
8 ай бұрын
@@tawsifchowdhuryaraf8866 it could be that you tried to draw more current from the UNO board and thus damaged the voltage regulator. Use a multimeter to check your 5V and 3.3V pins on uno are giving the right output voltages
hi, my code isn't getting reset after pressing the red reset button. I've tried a lot but haven't been able to. Please help
@Circuitdigest
11 ай бұрын
that's strange, how do you know that your code is not getting reset? are you able to upload code normally ?
@amitsinhapune
11 ай бұрын
like i put a blinking code, it runs. I press the reset button and after the blinking it starts running again. I'm buying a new one so no worries I guess.@@Circuitdigest
@Circuitdigest
11 ай бұрын
@@amitsinhapune cool, but i still dont see any problem with the way you describe your boards working
my arduino "ON" LED blinks only once when i am plugging in. can i fix it?
@Circuitdigest
Ай бұрын
The ON LED is connected to the 5V line though a resistor. Check 5V line make sure there are no shorts and the 5V is present.
My arduino works when the USB cable is connected to the laptop but when I remove the USB to connect another power supply my program does not work. Please suggest what should i do?
@Yogesh62
5 ай бұрын
Same problem bro
My arduino for some reason constantly gives high output to digital pwm pin 3. Can you please tell what could be the problem? 🙏🏻
@Circuitdigest
3 ай бұрын
If a pin is always in the same state regardless of the code, then post probably the pins is damaged.
Bhai Mera exit 1 status error dikha rha he upload nhi ho rha he plz help kya Karu me 😢
@Circuitdigest
Жыл бұрын
is it coming during compilation or uploading?
@NovaGamingNexus18
9 ай бұрын
uploding@@Circuitdigest
Light no not working 😢
Bro please help me com port not showing when I attach my UNO board with laptop. I've done everything I possibly can. CH340 driver is pre installed. I replaced my USB A-B cable. Still no ports or other devices showing in device manager. I've reset the Arduino board and my laptop as well. Nothing works. Please help!!!🙏🏻
@Circuitdigest
Жыл бұрын
try changing the bootloader
@tuhinguha434
Жыл бұрын
@@Circuitdigest Do I have to burn the bootloader by another Arduino board?
After uploading code .the aurdino getting connected and disconnected and again connected and disconnected
@Circuitdigest
10 ай бұрын
Sounds like a hardware problem, My guess is that you have connected some motor or sensor which is consuming a lot of current forcing the Arduino to shut down and power on again. Remove all your hardware connections and try again
@fa36184
8 ай бұрын
Just like mine
My arduino only run one program, i change with onther program but not working . I also reset it but still run first program. What should i do?
@Circuitdigest
8 ай бұрын
this is strange - are you able to upload the new program successfully?
@thelegendarygamers1272
8 ай бұрын
I am also facing the same problem
@Circuitdigest
8 ай бұрын
@@thelegendarygamers1272 i remember having a problem like that - the reason was a fast loop in my code, try pressing the reset button on Arduino and releasing it just before your code starts uploading
@thelegendarygamers1272
8 ай бұрын
@@Circuitdigest I have tried that but it did not have any effect on it. I installed the legacy Arduino IDE and there it showed me this error avrdude: verification error, first mismatch at byte 0x0000 0x62 != 0x0c avrdude: verification error; content mismatch On the newer IDE, I am not getting any sort of error. The sketch uploads without any sort of error on the newer IDE but it doesn't have any effect on the Arduino and it keeps running the same old sketch.
@KayXamTutorials
4 ай бұрын
This is exactly my same problem with Arduino Leonardo @@thelegendarygamers1272
My arduino is working but when I connect sonsers it is not working 😵💫😵💫
@Circuitdigest
Ай бұрын
Without a little more context we can't help you. Please use our forum to get more help.circuitdigest.com/forums
I have a Arduino pro micro and successfully build a volume control with 3 touch button(ttp223), but there is a problem pro micro often got disconnect not fully (like light glow when i touch the sensor but no light on rgb ring and volume knob also don't work)automatically i don't know why and every time i need to replug it to pc and make it work, do you how to fix it link from where i made it kzread.info/dash/bejne/lIGD17mbc9bNgKw.html
@Circuitdigest
3 ай бұрын
Make sure the Arduino is not stuck in some loop. Check your code.
Bro can u help me
@Circuitdigest
Жыл бұрын
hi there, can you kindly tell us what problems you are facing?
mine never worked in class
@Circuitdigest
10 ай бұрын
Actually learning starts when something stops working
You help me
@Circuitdigest
7 ай бұрын
do you need help?
@Pixelpulse_gaming01
7 ай бұрын
Yes
@Circuitdigest
7 ай бұрын
how can i help you?@@Pixelpulse_gaming01
king
Hello
@Circuitdigest
Жыл бұрын
hi there, how can i help you?
@Everythingvideos12
Жыл бұрын
I was working with the Arduino and I accidentally followed the wrong circuit then smoke came out of the voltage regulator. I don't have a soldering iron
короче я тебе на видио споливкой которое было годь назад ответь на комент пжжпжпжпжпжпжпжпжжпжпжпжпжпжжпжпжпжпжпжжпжпжпжпжпжжпжпжпжпжжп
Qq