I love how short, sweet, and to the point this video is. Thank you!!!!

Pretty cool you have the same printer and you have videos on the two things I was looking up. This video and the one you had with spandex and rubber soles. Keep it up, these are very helpful.

Thanks for the tips 👌👍

Great tutorial. Will be trying this on my wolverine mask

Awesome video, Emily!

@universeofemily

9 ай бұрын

Thank you Andrew!!💖☺️

Great tutorial! That putty acetone mix will be tested here too. Thumbs up.

Thanks for useful videos thanks for sharing love it

Great tutorial! I use straight spot putty from a squeeze tube. But I’ll try the wood filler and acetone method as well.

@universeofemily

9 ай бұрын

Thanks! I like spot putty too, but I think there’s pros and cons to each re: strength, sanding speed, fumes, etc. let me know what you think of the acetone and wood filler! ☺️☺️☺️

@alexh7663

9 ай бұрын

@@universeofemily will certainly do! I have two knee pads to prep so I’ll try it my own test!

Nice one again. About to test the wood filler acetone mix for the first time on my klingon Bat'leth that just finished printing 😏

@universeofemily

9 ай бұрын

Heck yeah! Let me know how it goes!

I seen your short , using the acetone and wood filler and I didn't get the right Constance. But this video helped

You are Best ❤❤❤

I just finished following your tutorial and it came out great! I usually use bondo but I wanted to try wood filler because I’ve heard the smell isn’t as strong.

@universeofemily

7 ай бұрын

So great to hear!! Yes! Bondo has a time and place but a huge plus of woodfiller is less toxic smell

I have a Neptune 4 and I’m really wanting to print cosplay pieces like this. I’d love to see a video of how you size your pieces correctly for your head/body and what your solution for printing pieces in parts are when you have to bond them together afterwards

You can print these much faster , use a .8 mm nozzle and print these in single wall thickness , like in vase mode afterwards you can reinforce it with epoxy or fiberglass or any other material , there are videos available online , that demonstrate this method .

@universeofemily

9 ай бұрын

It’s all about the balance between print time and post-processing time in my opinion! Lots of different ways to do this, and this is the most enjoyable for me. Cheers!

Can't seem to find your video talking about the pros and cons of woodfiller vs bondo. I'm going to be tackling a mando helemet print so I'm open to all techniques before trying any myself

@universeofemily

8 ай бұрын

Hi! Sorry it was too long to fit on YT shorts. Here is the link to the vid on IG: instagram.com/reel/CxvWoE2LXMd/?igshid=MzRlODBiNWFlZA==

What mask do you recommend to wear during this process -- also AWESOME helmet!

What kind of paint brush are you using?

This tutorial is awesome! Question, for the process after the sanding the wood filler, how to clear off the dust? Wash it or what is the better method?

@universeofemily

8 ай бұрын

I just wipe it with a dry shop towel! The wood filler i use is water soluble, so i wouldnt wet it before adding a layer if primer/other paint

@matteblack144

8 ай бұрын

@@universeofemily Awesome! Thanks for the info, will apply it later on in my next Prop project

@universeofemily

8 ай бұрын

@matteblack144 awesome!! Let me know how it goes!

At which stage are you using which kind of sanding paper?

@universeofemily

9 ай бұрын

Hi! The first sanding is 120, and the second is 240

what kind of 3D printer you have?

@universeofemily

9 ай бұрын

This was printed on the creality cr-10!