Thanks for the dust shield and bracket portion of the video! That was the ticket for me.

@s33therfan

5 ай бұрын

Glad it helped , thank you for the feedback.

Thank you so much ,amigo . .gracias

@s33therfan

10 ай бұрын

You are welcome , thank you for the feedback.

Thanks!! This disassembly also worked on a 08 dodge caravan. Tutorial helped a lot.

@s33therfan

3 жыл бұрын

Thank you for the feedback and thanks for watching.

@ozzhanettalee4157

3 жыл бұрын

I came to the comments looking for this. I have a 2010 T&C

I got to hand it to you buddy very in-depth step by step was wonderful made my job easy thank you my friend

@s33therfan

2 жыл бұрын

Thank you very much for the kind words and thanks for watching.

Great video thank you for sharing, I always put sealer on the pan side and on top of the gasket, never had any leaks!!!

@s33therfan

Жыл бұрын

Rtv works great , thank you for the feedback.

Not too bad of a job definetely, thanks. My van changed the oil pan it's been leaking changed a gasket and still leaking

@s33therfan

2 жыл бұрын

The rear valve cover gasket is notorious to leak also , it requires removing the intake to access. But this may be your issue. I have been fooled before and replaced an oil pan gasket only to find it was a leak running down , giving the appearance of an oil pan leak. Thanks for watching.

Great job, thank you for sharing! Maybe a cheap jack stand from Harbor Freight?

Thank you, very helpful!

@s33therfan

2 жыл бұрын

Thank you for watching.

Great video! Thanks for sharing.

@s33therfan

2 жыл бұрын

Thank you for watching.

Thank you for the great video 👍 Got a question for ya. Will a bad pcv valve cause engine knock after time?

@s33therfan

3 жыл бұрын

I would say it could if it was causing excess moisture to build inside the engine. This can be checked by observing the oil cap and oil. A bad pcv can cause missfires excess pressure in the engine among other things . Thanks for watching.

Good video, going to do this on my '08 3.3L SE next oil change. She ain't pretty but she's mine :)

@s33therfan

3 жыл бұрын

Thats exactly right paid for and runs good is all you can ask for. Thank you very much for watching.

Thx for the vid. I'm working on T&C Touring 3.8L 2006. It's exactly the same, I was really hoping not to have to deal with the brace, but thems the breaks eh?

@s33therfan

Жыл бұрын

Thank you for the feedback and thanks for watching.

Great video just finished putting everything back but have a small transmission fluid leak at the bottom of the plate area did i do something wrong? Only really see the leakc when the car is stopped any ideas?

@s33therfan

3 жыл бұрын

Nothing you did would have affected the transmission. Either the pan on it was leaking or seal from within the transmission. If you are referring to the oil pan then its possible it could need the torque checked ( inch lbs ) , also possible there may be some damage to the pan surface but usually the gaskets will seal no problem. If I coud not get it to stop leaking I would rtv the gasket to the pan and reinstall it. Maybe even rtv the gasket to the engine also and it will definitely not leak once cured 24 hrs. Hope this helps and thank you for watching.

@juniorjones5137

3 жыл бұрын

@@s33therfan the oil pan worked out perfect but the little metal cover meets the transmission is where it is leaking a small amount of transmission fuild

@s33therfan

3 жыл бұрын

Ok that's a dust shield. If it's leaking there it's because of the torque converter seal that is leaking a small amount. This is pretty common with most cars after they have some miles on them. It's most likely it was already there but just not noticeable. Many times I have fixed leaks just to have others reveal theirself. But with the oil pan fixed atleast thats solved. Great job on replacing this and thanks again for watching.

Thanks

@s33therfan

3 жыл бұрын

Thank you very much for watching.

Exellent Vid But I Got The Pan Out Without Removing Anything , Just Had To Push On The Water pump Tube . It Will Give Just Enough To Slide The Pan Out ..

@s33therfan

2 жыл бұрын

Thanks for sharing your experience , and the feedback.

I did not have to take off the brace to get that cover off. Just had to wiggle it out the right way. Also, most MOPARs of the era can take a very large Motorcraft FL1A size oil filter which is a cheap and easy way to increase the oil and filtration capacity. My van increased from 4.5qts to 5.2qts. Just be sure to fill it with oil before you install it. Way better than those undersize cheap quicky-lube filters.

@s33therfan

Жыл бұрын

Great information , thank you for taking the time to share . Much appreciated.

Really good video, thank you. If you can do it with 1 hand, we should be able to do it with 2! 🤣

@s33therfan

2 жыл бұрын

I appreciate the great feedback. Thank you for watching.

I’m doing our 2007 Dodge Grand Caravan now. That foam rubber “shield/gasket” is dry rotted and broken. Do you actually know what this part number is called? I’d like to order the original part if I knew what it was called. I’m looking online and I can’t find it because I’m probably not using the right terminology. Thanks for any help on this.

@Vineyard_Edge

2 жыл бұрын

Mine was also dry rotted and pieces were breaking off.

What happens if that rubber or foam gasket on the dust shield breaks?

@s33therfan

2 жыл бұрын

It really is not necessary , however they sell thin weather stripping that may work to fix it. Thanks for watching.

What king cilicon did you use for the gasket?

@s33therfan

3 жыл бұрын

I either use ultra black for oil or the gray high torque rtv. Never had issues with either. Thanks for watching.