How to replace the diaphragm on Briggs and Stratton
Тәжірибелік нұсқаулар және стиль
Metal in Motion Outdoor Power Equipment Repair show you how to replace the diaphragm on a 3hp-5hp Briggs and Stratton engine. These motor are found mostly on base model push mowers or pressure washers.
Пікірлер: 183
Dude this is a outstanding video, honest and to the point,no loud music and lots of knowledge in a short video, thank you!!
Very concise and clear. Steps taken were very practical and sensible. Thanks.
THIS is the way a video should be done! Great job. No questions necessary.
Best video I found for the disassembly of the carb A great help ! Had it off , cleaned and reassembled in an hour thanks!!
I have been "frettin'", fussing, almost cussing and almost having a running fit ! I am so glad and appreciative that I found your you tube video on this lawn mower. I have the same engine. I listened to the video twice. Excellent Video ! Easy to Understand ! Thank you so very much !
I had a problem with the engine surging, and thanks to your video, I have repaired my B&S 185cc/5.00 lawn mower...What an excellent video...Nobody could have made a better video, I swear...Nobody. Great narration, Excellent video quality, And perfect step-by-step instructions. You have found your calling. I Subscribed. Thanks...Joe
This is one of the best DIY videos and explanations I have viewed regardless of the device or kind of repair. Videos on how to perform surgery should be so well done. Thank you!
Just spent £80 on a service for mine. With your help I can definitely do this myself in future. Clear and simple instructions. Thank you so much.
This video is a model of how these "how to" videos should be made. It gave me the information I needed without subjecting me to self indulgent showmanship. I just needed to know what I would find as I delved into the mechanism. I fixed my motor without any expense at all because dismantling and cleaning were all that were needed. Many thanks.
Brilliant video- thank you. Genuine diaphram for less than £3 off ebay, 25 minutes fettling later and mower is transformed. Changed my spark plug too ( NGK off ebay for £2.50!) and oil too. Now intend to take better care of my mower from now on.
I have a Bolens push mower with a 3.5 hp Briggs and Stratton with this exact carberator. Have done this service several times. My symptoms have been engine surge but this service fixes it. I noticed water as well as grass clippings/ debris makes in inside the tank. I can see how water can get in there but can't figure out how the other trash is making it in there. These carbs are very easy to work in though as is the whole mover. Nice vid and thank you for sharing.
Thanks so much for this excellent video.Transformed a sputtering, hard to start push mower into a smooth running machine. Could not have done it without your detailed instructional video.
Excellent video. Real easy to understand. Thank you!
Perfectly done video showing the process step-by-step and little hints along the way of what to watch out for to make sure the repair goes without a hitch. Just repaired my 5 year old Craftsman edger in less than 30 minutes. It is up and running like new. I couldn't find a local shop to work on this small engine, and even if I could they would have charged at least 10X what it cost me for a new gasket/diaphragm!!!
Thank you so much for posting this video! I am a 52 yr old single mom and my mower would not stay running. Followed your video and it now starts first pull every time and stays running! You are awesome!
A clear and concise video which has proved to be most useful in the repair of my lawn mower. Many thanks for all of your help , very much appreciated !
Spot on!! Clear & precise, 24 mins start to finish & running sweet as a nut again, all for £3.60.
Absolutely first class, I've followed the step by step instructions & my mower works like new. Excellent video, clear & concise.
Excellent instruction video, Josh. Very clear on the verbal instruction and excellent camera work to help us see exactly what you were doing as you described it. Great job! Thanks!
Thank you. And I mean that from someone who doesn't know anything about small engines. You made this so specific and easy to follow. Thanks again!!
Great easy to follow video. my mower is now running like new!!!!!!. Thanks Josh, keep up the great work.
Many thanks this is almost identical to my model which I have to prime with a spoonful of petrol as the button is perished, but which recently started firing up then cutting out when the primer was burned. Stripped down, new gaskets cut by hand, cleaned out, reassembled and now runs better than ever.
Mower was running rough, watched your video and after cleaning carb ended up replacing the gasket and diaphram for $8 and works like a champ. Thanks! Used the B&S p/n 5083 combo includes spring and screen.
Thanks for this useful video. The explanations are concise and the approach very methodical. Well done!
Thanks for your time and talents!
Ken Ishida is exactly right. This IS one of the very best DIY videos and explanations that I have seen - and I've looked at plenty of them. Thank you Metal in Motion.
I checked out my mower this am, you are the best it is now purring like a kitten....great video.....i also changed my oil, spark plug, blade and cleaned the machine.....thanks again.....I found I was missing a screw in the front so thanks for that info..
great video, covers it 100% thanks
Fantastic Info - Lawn mower now runs like new, Thank you.
I saved myself at least £60 by following this video demonstration Thank you
Great stuff. Clear, concise. My Nana could do the repair following your instructions!
Great video - so easy to follow and my lawnmower works like new (at least as new as when I got it!) Thanks very much.
What a clear an awesome video thanks for the tips now I have to go and do this to mine 👍👍
Excellent description and photography of what's involved. Thanks
Brilliant video wished I had viewed it earlier as made mistake removing tank,& had to replace a spring but now I know how
Very nicely presented.
What a brilliant video. to the point and full of information. Thanks
Thanks a lot mower running well now saved me a big repair bill
you saved my lawn mower today. I forgot to install the O ring you show at 4:01 so not enough gas inside of the motor because of not enough succion for the membrane pump. Many thanks.
Thanks, worked a treat, I'm so happy Your the man
Great video. Very informative and precise, thanks very much!
Josh - The Best DIY video I've seen on You Tube. Great video. Clear explanation! Very good job and thanks. You saved me $150!
Thanks for the video, very informative, clear and well-done.
Same fuel restriction problem on my B&S 3.75 power washer. It would run for 3 seconds after priming. Diaphragm looked OK so I soaked the plastic gas pick up tube and screen in paint thinner (didn't have anything stronger) for 24 hours. Blew out the thinner with a compressor, reassembled. Starts and runs great.
Excelente...! u r a master.. Thank you so much from Buenos Aires., Argenitna.
Excellent video.very professional, very helpful, thank you very much.
thanx Josh, you make it look so easy...
good job Josh,learned alot. good music too.
Great vide Josh Well executed and clear
Superb explanation! Thank you!
Thanks for super video,we had an old mower going well,great,M.
really helpful. Thank you Josh
Great video thanks, definitely saved me a few quid.
Nice video! very informative, picked some good points. Thanks.
You just saved me 100$. Genius!
Great Video - thanks for uploading it !
great step by step video!!! ty
Outstanding video! Thank you very much!
Excellent. Very clear and passionate. Very concise way of speaking, no extra words ! You should do more videos or Corporate Videos ;>)) Thanks, I found many details that were wrong with my 2d hand mower !
Excellent video. Thank you.
Well done to the point very clear well informed
Very detailed information. Great job thank you.
Good video...worked for me I did not tighten the Philips screws tight enough leaking a little bit gas. Thanks.
Hey Josh, You did a terrific job of explaining this procedure. Now I'm going to try and fix my mower. the mower starts with primer spray but stops as soon as the primer spray has been burnt. Probably a plug gas line ....so hear goes. Thanks
Great video ... While you've got the air filter off you need to check the cleanliness of the sponge filter. If the sponge is dirty, wash it out and when completely dry add a few drops of clean oil to the sponge.
Thanks very nice video easy to understand
Excellent video...thanks.
Nice video , swell job thank you.
Great Video, Thanks!
thanks from the uk. i've got a working lawnmower again. nice one.
@froggerabc
7 жыл бұрын
well i thought i had. it only seems to run on the petrol that the primer puts into the carb when you prime it. any ideas. the primer is supple enought when its out of the tank.
Good Morning.. The pull assembly not broke.. The string came off the spoil. Tried to put it back on and a coily like spring came from under it?
A great help. Thanks.
thanks, straight forward and to the point.....
Thanks for the help!
Very useful vid. Thanks very much
Great video!
Great job!!
Muy buen video, gracias me sirvió de mucho.
THANK YOU FOR YOUR INFORMATION VERY GOOD.
Very good video thanks a lot
I like the information about the small engine
thanks bro it really helped me just need 1/2 and i am, good
Great Job, Thanks
GREAT INSTRUCTONS. thx
Oh Dang...I blew it with my mouth before I read your disclaimer that came later......Your done fer!
Just watched the video going to attempt to do mine tomorrow........wish me luck
You are real good MAN,your ORIENTATION PERFECT 👍👍👍👍👍👍😍😍😍😻😻😻
very good ; Josh excellent thanks
Thank for great video
great vid, now maybe i can get mine goin
I have a 1984 b&s M4 mountfield major, im not sure what HP she is although the sticker has faded most of it but i can just see 5HP, but is it a 3.5 or a 5?
I have tried to replace this, but I seem to have a petrol leak on the front of the carb, (on the diaphragm under the O-ring) opposite side to primer.. I cant tighten the screws anymore then they are now? the diaphragm looks flat but its still leaking>?>
EXECELENT BROTHER......
I followed this video step by step with new gaskets fresh fuel however the motor still surges any thoughts ??
Excellent.
Does that gas tank leak around the seem? Looks like it may from here? I thought i had carb problems till discovering leaks around tanks seem when i poured and rinsed out tank. Lil quicksteel solved me is it this or that or how bout this.. Lol. Thanks for good info video!
Great vid, thanks! :-)
The wind vane is such an elegant method to maintain constant rpms. I wonder who invented it back in the day.
@theropod0001
3 жыл бұрын
Some time after the “hit-n-miss” ignition system was abandoned. Flyball governor systems kept those old engines from over rev, and work much the same way. A force is either applied to a rod or it isn’t.
More Videos More Videos! #Great Video
good job... thanks