How to Replace Lower Control Arm 1994-2004 Chevrolet S10
Автокөліктер мен көлік құралдары
Buy Now!
New Control Arm with Ball Joint from 1AAuto.com 1aau.to/id/1ASLF00215
This video shows you how to install a lower control arm on your 1994-2004 Chevrolet S10. Control arms are a crucial part of the suspension system of your vehicle. They not only carry the load of the vehicle to the wheel, but they typically also maintain its alignment. Control arms are typically large and strong, so you may be surprised it needs replacing. They contain rubber bushings for smoother rides at the cost of eventual wear, or integrated ball joints that require replacing the entire arm when they wear.
This process should be similar on the following vehicles:
1994 Chevrolet S10
1995 Chevrolet S10
1996 Chevrolet S10
1997 Chevrolet S10
1998 Chevrolet S10
1999 Chevrolet S10
2000 Chevrolet S10
2001 Chevrolet S10
2002 Chevrolet S10
2003 Chevrolet S10
2004 Chevrolet S10
Tools you will need:
• Pry Bar 1aau.to/oa/1AXAA00020
• 14mm Wrench 1aau.to/oa/1AXAA00010
• 18mm Wrench
• 21mm wrench
• 7mm Wrench
• 13mm Socket 1aau.to/oa/1AXAA00015
• 14mm Socket 1aau.to/oa/1AXAA00015
• 18mm Socket 1aau.to/oa/1AXAA00043
• 19mm Socket 1aau.to/oa/1AXAA00043
• 21mm Socket 1aau.to/oa/1AXAA00043
• Needle nose pliers 1aau.to/oa/1AXAA00051
• Needle nose pliers 1aau.to/oa/1AXAA00052
• Side Cutters
• 11/16 Inch Socket 1aau.to/ob/1AXAA00016
• 7/8 Inch Socket 1aau.to/oa/1AXAA00042
• Ratchet 1aau.to/ob/1AXAA00016
• Torque Wrench 1aau.to/oa/1AXAA00044
• Bungee Cord
• Rust Penetrant
• Hammer 1aau.to/oa/1AXAA00091
• Jack Stands 1aau.to/oa/1AXAA00065
• Pick 1aau.to/oa/1AXAA00037
Subscribe: / @trq
⚠ DISCLAIMER:
While TRQ strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. TRQ is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
Пікірлер: 21
√ Watch the Video √ Buy The Part at 1A Auto 1aau.to/m/Shop-TRQ-Parts √ Do it Yourself √ Save Money
This is the route I'll be taking now because I tried pressing my lower ball joints out for 4 hours and finally gave up and returned the pressing kit. Buy the lower control arms and replace the shocks while I'm at it. Great video.
This is the 2WD version for those wondering. The 4WD version does not have coil springs to compress. Instead, it has a torsion bar you have to unload.
I have been working for two days trying to figure out how to separate the spring from the lower control arm, which just a little force with a crowbar. You explained and showed it very well in this video. Thank you.
Man when I tell you that Rachet strap is important I MEAN IT.
Excellent video
well i guess my end links are loose because i surely dont have mine cranked down like yours hmm,cool,i replaced my lower control arm,it was bad the front end had been in a fender bender before who knows how bad but the lower control arm bushings were bad the metal was bent,the tube bushing inside the rubber it was pushed up against the control arm to the point the arm was peeled back some,i was like wow,that really needed changing,i put the floor jack under the edge on each side and slowly raised it up and the bad one went up and down,plus it squeaked when i would get in and out of my blazer,2005.rwd so great video,i mean ive did the lowering kit on it but never changed the control arm,i did on a tbss and that sucked bad omg.
great video
How did you finally get lower control arm in place with spring tension being so high? Did you strap the vehicle to the lift so it wouldn’t lift off? Or did you purely using a ratchet strap + the high reach jack stand?
One question, teacher, the spring coil, it has a rubber coil spring in the upper and lower part???
Great video!!👍👍👍
One question does the spring coil have rubber on the top and bottom???
@disastreee
Жыл бұрын
yes
So everybody S10 lower control arms just going bad after 20 years
Why not use a spring compressor? It would have been a lot easier to install.
Front control arm kit for zr2 1999
This must be a 2.2, the spring without something to compress it simply does not fit back into the truck that easily. At least it surely doesn’t on any 4.3 truck I’ve ever done. You’ll flip the truck off the lift before you get the spring where it lives.
He never tightens the upper ball joint
It needs a lot of tlc
This was one of the worst jobs of my life
Not safe Dont try agian👀