How to Replace Idler Pulley 07-09 Toyota FJ Cruiser
Автокөліктер мен көлік құралдары
Buy Now!
New Drive Belt Component Kit from 1AAuto.com 1aau.to/ia/GAEEK00246
In the video, 1A Auto shows how to remove and replace a wobbly, squealing or seized idler pulley. The video is applicable to the 07, 08, 09, 10, 11, 12, 13, 14, Toyota FJ Cruiser.
🔧 List of tools used:
• 12mm Socket 1aau.to/oAI/1AXAA00015
• 14mm Socket 1aau.to/oAI/1AXAA00015
• Ratchet 1aau.to/oHa/1AXAA00016
• Socket Extensions 1aau.to/oAI/1AXAA00015
For More Info visit us at 1aau.to/h/bLt/
⚠ DISCLAIMER:
While 1A Auto strives to make the information provided in this video as accurate as possible, it makes no claims, promises, or guarantees about the accuracy, completeness or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself projects entail some risk. It is the sole responsibility of the viewer to assume this risk. 1A Auto is not responsible or liable for any loss damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
Пікірлер: 18
√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*
You mention it gets tighten to 28 inch pounds of torque which I thought it was too low so I look up my repair manual and it says that it should be tightened to 29 foot pounds of torque which is a big difference
@nordicpride9708
2 жыл бұрын
But you never make mistakes right Carlos?……..🙄 use common sense as a mechanic and don’t just trust the internet. End of lesson
@Ty-tie_FTW
Жыл бұрын
May be common sense, but he actually torques it to 28 inch lbs on here so people are gonna listen. If you plan on keeping your fj, you may as well pay for the toyota repair manual. It's expensive but very nice to have for the torque specs
Yes I agree with Carlos I don't think the torque for this pulley is supposed to be 28 inch lbs. The Toyota manual says to torque the No. 2 idler to 29 foot lbs.
@1AAuto
4 жыл бұрын
+Zac Bron Thanks for the tip! We'll pass this info along to our production team.
Am I correct is assuming this will work on Tacomas in the same year range with the same 1gr-fe engine?
Looking to do this on my 07 4runner. Thanks for the video and follow up comments about the torque spec.
@1AAuto
5 ай бұрын
+@hadjih Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c
I’m just curious, if you’re just replacing the upper passenger side pulley, wouldn’t it be easier just to do it from above? And not have to remove the skid plates below? I was looking mine earlier and seemed like it would be pretty easy to access for up top… but wanted to make sure before I did it!
@RailfanRowan
Жыл бұрын
Hey there, I found easier to lay on my back and do it from underneath on my 07 FJ, came back to this video for the other upper and lower not demo'd. If you have no lift like most of us don't, try your back, legs underneath the vehicle, eye under engine, up on blocks. Worked for me good, took 5 minutes. No need for a tech. Also I have no more front skid plate lol 😆
@Ty-tie_FTW
Жыл бұрын
The skid plates are a pain. Mine has a lift and the diff drop and the stupid skid plates now have to use 1/2" spacers to clear the diff drop, just to make it even more of a pain
the idler pulley bolt torque should 29 ft.lbs ..................................... NOT 28 inch.lbs!!
@1AAuto
3 жыл бұрын
+Water Boy Thanks for the tip! We'll pass this info along to our production team.
Super easy job, follow along! ... Step one : Buy a massive car lift ._. lolol jk
Holly rust!
29 Foot Pounds.
Calibrated forearm 😉