√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*

@brittanycato3748

3 жыл бұрын

My door wont open from the inside or outside, how can that be fixed?

Attaching the cable end/ball to the door handle on the door panel would have helped a whole bunch. That 'step' can be very challenging!

Here’s a tip to save you a bunch of time! Don’t take the whole latch out of the door and disconnect the rods. Just unscrew the latch and pull it back just enough to disconnect and connect the cables.

@stirings

2 жыл бұрын

I was messing around with that yellow clip on the rod for so long. Your comment saved me so much time. Thank you

@billp.3230

2 жыл бұрын

Thanks for your reply, I was just wondering if I actually had to do all of that but now I know I don't.

@anything9988

Жыл бұрын

You are completely right, I just did it and it took about 30 seconds to remove and replace the latch end of the cable once it was unbolted.

@tjdillon9827

Жыл бұрын

Dude I owe you a drink

@bigcartoonyIIV

Жыл бұрын

I tried your way, and i did the entire fix in less than 20 mins

Do we just skip the part where you connected back to the door handle?

Thank you for this video but it has WAY TOO MANY UNNECESSARY STEPS!!! Skip between 7:00 and 8:07. This is NOT NEEDED! If you try to undo that yellow plastic clip that goes on the rod that goes up to the door lock most likely you'll break it - and because of the power window assembly on my truck I literally couldn't get my hand in there regardless. You don't need to use the pick tool to pop off that other rod either. Go to the 8:07 point where he undoes the torx screws. Undo those. The latch assembly is not very tight in there and you can easily pull the latch assembly forward towards the open area of the door (front of the truck direction) and you can get at the latch to replace the door handle cable. Now skip to 10:50 and watch to 11:40 to see how to remove the broken cable and put the new one in. Place the latch where it was and screw the torx screws back in. Now skip forward to 15:55 since all he is doing between 11:40 and 15:55 is reassembling the stuff he didn't need to disassemble in the first place. Resume watching at 15:55 and put everything back together. (This video also works for power windows as I have those in my 2011 Silverado - just be sure your power windows are up before starting this process- and I find the cable to window controls on the door panel are long enough you don't have to disconnect those to do this cable replacement either).

@1AAuto

4 жыл бұрын

+Jeff Axel Thank you for the feedback. 1aauto.com

@benjamingardea4511

4 жыл бұрын

Jeff Axel thanks for pointing that out. Saved me a bunch of time! Thanks for the video gents.

Looks like he skipped the part where the cable attaches to interior of the panel. All this work, and you would still find yourself having to roll down the window to open from the outside.

@TheAxmaker

3 жыл бұрын

If you are referring to the inside of the door handle, wouldn't that be a given since you just hook cable back up in reverse of taking it out? The video worked fine for me.

@paulmoon9818

2 жыл бұрын

Hmmm 🤔 what did he forget to do here ? Lol

@360ModsandHacks

2 жыл бұрын

@@paulmoon9818 connect the cable to the interior door handle. My clip broke off where you connect it to the interior door handle and that's why I'm here. They didn't show him connecting it.

I watch e different videos which did not help they always cut the scene and then the next clip its out in her hand. But by watching these videos it helped me. I just disconnected the yellow clip took the three bolts out of the door lock, then you can pull the lock out where you can get a needle nose flyer to pull the cable off it was a breeze. Total job took less than 45 minutes

Muy buen video sin dejar dudas y muy bien la explicación y los pasos a seguir 👍

This video made my job of changing cable so much easier. Thanks so much

Thank you man you save me a lot of trouble !! the video is very clear and very very helpfull ! from Montreal Canada !

Ditto on the inside handle hookup. Thanks for the comments about not disconnecting the rods. Suggest the guys with the door not being able to unlock, problem is locking rod is not in correct position either in the yellow snap box or the grey plastic top of the rod. Thanks

Thanks a lot for this video I wouldn’t have ever honestly figured it out on my own. Y’all’s channel have saved me lots of time and $$$$

Just replaced mine thanks to this video. I really appreciate your help 👍

@1AAuto

5 жыл бұрын

+Beto flores Thanks for checking us out. Shop here for high quality auto parts:1aau.to/m/Shop-1AAuto-c

This video was awesome and sooo helpful! Thank u! Saved me a ton of money

@1aautoparts fo you have a video showing you guys changing the lifters in a 5.3 engine?

Yep! Would have been a complete video if he had re-atteched cable to door handle between 16:00 and 17:00

@fredwalters3210

2 жыл бұрын

Actually, With smaller hands you can align the left end cable up with the hole, insert it and push on the cable right end and the ball will extend further on the left, door mechanism side. The v notch is spring loaded, just let the cable end get caught behind and you are half way there. No need to remove 3 30 star bolts or manual lock bar from inside. Put the foam panel back in place. Then you can place right end cable ball in hole with needle nose plyers. THATS about it.

Piece a cake...and saved me a ton of $$$...thank you

@1AAuto

4 жыл бұрын

+Corlis Dobson Thanks for checking us out! 1AAuto.com

Is this the same cable as for a door with power door locks? Or do you have the cable for doors with power locks? pretty sure they are different. thanks.

I had to dremel tool a hole to get the second clip to come out, to hard of a reach area to manage to remove the pins on the cable. Overall, great video on how to do the task!

I got lost, at what time did he connect the cable to the handle?

What size cable do I need for the auto lock doors on 2012?

What size cable do you need for the back door?

Stuck at 15:45 where the handle rod is supposed to latch to the yellow box with a "door" My truck doesn't have the door it just snapped off. Did I just break it or can this be fixed?

Thanks.. Easy easy easy!

@1AAuto

4 жыл бұрын

+Dustin Kirkpatrick Thanks for checking us out!

I have a 2011 work truck but my door handle sits above the window crank. Do you know what part number that is?

Does anyone know if this works on power door locks? The a1website does not have an option for powered door latch cable.

If you're worried about those rods on the latch I just did this without removing them just had to reach in behind the door.

@TheAxmaker

3 жыл бұрын

That worked great for me too and saved time.

Is it just me or did he not connect the cable to the interior door handle?

@Howtoinstallwindowsinyourhome

5 жыл бұрын

If he did, he didn't show that step.

@DAJeeper1

5 жыл бұрын

wesley lokey same reason I was watching the video lol

@tiffanyfambro56

5 жыл бұрын

I was thinking the same thing...he did not

@josiahbegay1098

5 жыл бұрын

No he did

@steve874

5 жыл бұрын

I didn't rewatch, it's possible, we've all done stupid crap like that before. Lol

I dont have power locks. Mine is manual, but my inner latch isnt opening my door. It works from outside but not the inside

This works on a 2012 silverado?

Can you take the window crank off without that fancy smancy tool??

my gmc has power door locks. will this cable work since it states (manual lock) in the description?

@appliancedude63

3 жыл бұрын

I have the same. I think it's a longer cable.

What do you do if the nylon ball on the end of the cable at the lock mechanism will not stay in place? I've installed the cable, put everything back together, and tested the interior handle, 4 times. Does not open the door. Pull everything apart again and the ball on the end of the cable at the door lock has pulled out of the Y-shaped fitting. It will not stay in.

The part where he connected inside latch part wasn't in video?

So I’m having the same issue on my 2008 and wondering what causes the problem? What part of the cable is not connecting or allowing the function of the door handle to work properly?

@lamorferguson950

3 жыл бұрын

Im having the same issue. Did you solve the problem yet?

@PaulLaFleur76

3 жыл бұрын

My cable snapped.

@drivewaygarage1561

2 жыл бұрын

I took mine apart and the cable was broken by the inside door handle

perfect.. my passenger door finally locked itself.. both inside and outside handles cant open the truck .. Need a solution on how to top the door... 2010 model. ofcourse silverado 4 door LS

@victorscott6831

3 жыл бұрын

Happened to me when sorting the passenger side for the 5th time. Was able to lift and separate the inside panel from the top and reach between and manually pull cable. Hope it helps u out.

anyone have any tips on how to get the door open to do this? The cable on my 08 silverado is completely shredded and I have no way of opening the driver side door.

what size is the cable

I have 2013 GMC Sierra SLE. My door won't open from the inside or out. It started with the outside door handle, now the interior doesn't work either. Any help to get it open to replace handle? Thanks

@antoniokeys426

3 жыл бұрын

You ever figure it out?

You don't have to do all of this, forget the rods, not necessary. As soon as you get the panel off take the the three bolts out of lock mechanism, push forward to opening in door, change out cable, reassemble.

@1AAuto

5 жыл бұрын

+Steve Thank you for your feedback!

@terrypayne3369

5 жыл бұрын

I was wondering about that. Have my door apart now. Waiting for the cable to come in a couple hours. Was going to try just removing the 3 bolts from the lock and pushing it back to get to the cable. Hoping I don't have to fool with the other stuff.

@kylefinkbeiner556

5 жыл бұрын

I just did this today and this guy is correct. The latch assembly swings far enough forward to swap out the cables easily without touching those rods.

@krww7425

5 жыл бұрын

Thanks for the tip. Also thanks to the original video.

@davidmcclary4507

2 жыл бұрын

Yep.

This video helped me overall but having power locks actually makes the replacement 10 times easier than the video shows. Just make sure you don't order cheap replacement parts online like i did and it will save you a headache.

@josephgreene9861

Жыл бұрын

How can the door be opened when the cable is disconnected

Whats the length of this product (cable) ? The link doesnt say.

@1AAuto

4 жыл бұрын

+Chris Alerta Alpha We do apologize but we do not have the spec.

Second video by these guys that was zero help getting the cable off the back, one said "squeeze that clip" and the other said squeeze those tabs".. Both while blocking what they were actually doing. I only looked this up because I was tired of balancing the panel while trying to see what held the cable in. Thankfully there's a bunch of other videos that actually show you what you need to be doing back there... Instead of fishing around and breaking the cheap plastic these things are made of

Both of my doors wont open from the inside or out what do I need to do to get one of them open

@BudG843

4 жыл бұрын

I popped my panel halfway off just enough to get my arm down in there. I grabbed the cable and the door handle from the inside at the same time over and over and luckily it popped open somehow. After that it started opening from the outside only.

@chrisalertaalpha4291

4 жыл бұрын

Just crack the top part of the panel and pull on the black cable that goes from the handle to the lock mechanism

man you guys didn't mention on the lt silverado theres an extra rod and im now having to figure out how to disconnect myself. thanks.

But you didn’t make the final connection! All that and no chips .

Does the battery have to be taken out to replace the cable?

@1AAuto

4 жыл бұрын

+Antoinette Lopez Thank you for checking us out! No, it is not required to take out the battery to replace the door latch cable. Please let us know if you have nay further questions, thank you.

how you opened the door???

Dude uhhhhh........he didn't reconnect the cable to the handle. That part where he gets it back together and starts cussing up a fit would have been very entertaining.

I think you missed the most important part. Still a very helpful video

Now do it like normal with the door closed that would be quite a helpful video

I'm not even a professional like ya and I removed the latch without taking the whoel thing off😅

Attached everything correctly. Makes the noise that it makes to unlock the door but doesn’t work.

@1AAuto

3 жыл бұрын

+Tyler Thanks for the feedback!

This looks so difficult. My driver side won’t open from inside or out. To repair it at the dealership is too expensive...where can I order this part?

@1AAuto

4 жыл бұрын

+Brisa Castro Here is the link to this part # www.1aauto.com/chevy-gmc-front-driver-or-passenger-side-door-lock-latch-cable-dorman-924-360/i/1admx00224?f=912835&y=2008 Thanks for checking us out!

it'd be perfect if the camera was on a tripod. too much movement from the hand held camera

How are you gonna skip the last part, connecting the door handle? I guess I'll go find another video.

window handle removal? Oh wait there is a special clip and a way to remove it?

@inrealitywetrust2610

5 жыл бұрын

All chevy's have the same tool all the way back from 1965 or so.

He never hooks the handle back up

It's fuckin nice when previous owner,s just throw the fuckin insulation pad away and no one makes it anymore fuckin lovely

Nice effort on the rod that connects to the red clip for the outside handle 🖕🏽

Overall ok but misses the boat where he loosens both vertical rods to the cylinder lock and the plunger lock. No need to do this, plus its a pain. Just skip those steps and remove the 3 external bolts holding the latch itself on. Once this is done the latch itself has enough play to access it and remove and install the new cable

@xnadave

4 жыл бұрын

Glad I read the comments. Thanks!

Pulling that latch is nearly impossible. That rod with the 90 degree bend in it will not come out. Call Rheem.

You never put the cable back into the handle!

Well I guess the mystery lives on with why the ball won't stay in the socket at inside door handle release. Now I get to take all of my seats out to get the door panel off. Thanks for nothing and giving me a bunch of extra work so I don't destroy my door panel. Dorman sucks!!!!

OMG sometimes you are just better to pay to get her done lol i quit !

Well, I just wasted 20 minutes. You never showed how to put the cable back on the latch. That's what I needed to know.