You are my Champion. Without this video, i'll change my washing machine. thanks a lot !

This is a great video. One thing I would suggest doing differently is the re-assembly. I would suggest fitting the metal bits before insertion into the hole. Do all of this fiddly metal cover and fastening washer bits outside the machine before you insert the element into the machine. It will make your life much, much easier ;-)The chap in the video used his special tool to tap into place but you can also use an appropriate sized socket from a socket wrench set. On the new element use some soap/washing up liquid in the rubber grommet holes and slide the grommet onto both ends of the element right down to the bended bit. Then attach the metal cover onto the element and tap it down around 0.75cm onto the metal of the element ends. Then tap down the fastening washer rings as well, right up to the metal cover and the whole metal assemby should ideally be now be sitting 1cm onto the element ends. Try not to go further than 1.5cm. Once the metal and washers are in place they are set, they will not move. Now when all set you can slide the element assembly into the washing machine hole and into place. Because the rubber grommet is quite far forward at this stage, use your fingers to press the grommet firmly into the hole at this stage. This method allows you the space to be able to seat the grommet with your fingers all around the edges. Once you know the grommet is properly seated, then you can push the protruding metal assembly and element forwards (like a piston) into the machine. This way you can now press the metal assembly firmly up against the grommet by hand. The washing up liquid allows it to slide forward easily but once the washing up liquid has dried nothing will move :-)

@jopepe7061

3 жыл бұрын

It's not so easy, I see......

Thanks a lot - it took me quite some time to find a video which actually shows the disassembly of the heater of my Miele WKF110 (which seems to be very similar to your machine).

Great video thank you! Everyone watching this make sure the element does not rub on the drum as pointed out by others happened to me too. Just give it a spin by hand once the element is in to avoid an annoying second strip down!!

Dear Yoram. I did it! I used another tooling - just a piece of plastic tube!

This was very helpful indeed. I have a couple of little additions that might be helpful to some. Be careful when pulling free the rubber seal - I was a bit too aggressive and actually bent/distorted the opening and had to carefully tap it back into shape with a bit of wood and a soft mallet. Even then - I wasn’t sure it would seal properly so I used a thin film of silicone bath sealant around the sealing rubber - it worked and actually helped provide a bit of lubricity to re- insert the element/rubber seal into the outer drum aperture.

@alexanderromanenko7372

4 жыл бұрын

Some lubricant is usefull

Thank you! It was really useful for me. I fixed my washing machine during quarantine.

Thank you much for a very informative video!

@YoramPomer

7 жыл бұрын

Thanks.. I am glad that I could help

You saved my day. Thanks!

Great Tutorial

Thank you from Denmark 🙏 Very helpfull

Very useful and helpful indeed. Thank You.

Great video and very helpful. I'm using a replacement OEM element and the rubber seal grommet that comes with it was ok but not as good quality as the original. Instead I used silicon around the edge of the original grommet. I removed the original very carefully and cleaned it all up and it was still very re-usable. The silicon also acted as a lubricant when re-inserting into the opening. That should now provide a waterproof seal and I think the original was fixed with some factory silicon anyway. I let the silicon dry for 24hrs before re-assembling the machine.

@YoramPomer

3 жыл бұрын

I am not sure that silicon is needed for sealing. One reason is that they need to be able to send a technician to a customers location for fixing all the problems on the spot. So that telling a customer to wait 24 hours before using the washing machine would not be acceptable. All of the parts that they replace need to be immediately fully functional. This is why the rubber seal can not be reused and needs to be replaced. I am happy that I could help.

@George-vl4lm

3 жыл бұрын

@@YoramPomer Hi, when I removed the original factory fitted seal there was a glue/silicon residue all around the edge. I used silicon anyway, firstly it acts as lubricant to slide into the hole easier and secondly there is no harm using silicon as it will guarantee a leak free fit (new or old seal). The OEM rubber seal grommets I was supplied were made of lower quality rubber than the original and I would defo recommend using silicon for them, there has been a lot of users of those who have complained about leaks afterwards. The new original Miele part is better but of course far more expensive. I removed mine very carefully and it was perfectly re-usable. Obviously if you destroy it on removal then you use a new one :-) My old one was defo better than the OEM supplied. Anyway 24hrs is not long to wait, I would personally use silicon no matter what (new or old) and you know it will not leak and saves having to re-open the machine and do it all again.

Your vid is just awesome!

@YoramPomer

6 жыл бұрын

Fischer custom baits Thanks .. It was a challenge to film the video at such a tight and dark location :-)

very useful, thankyou

Very good information, i was stucked not knowing what you do,, with this video I understand how o remove the resistance. What is the tooling to fasten the clips?

@YoramPomer

6 жыл бұрын

Thierry Collin It's my improvisation .. I needed something to press the clip evenly from all sides.

Thank you a lot!

Been trying to figure this out for 2 weeks now, because the rubber sealing won´t come off. Guess it's just glued onto it with all the "dirt" (don´t know the english word). Anyhow, thank you so much for this video! You saved me! Favorited and liked!

@TheMechas56

6 жыл бұрын

Fredrik Häll Hi there !!!!!! I'm a Miele tech ,and I did this repair around 3/4 years ago,believe it or not,it was crazy,it took me about 3 hrs to do it,if I have to do it again,I would take a different approach.Greetings.

Hello there, I have a Old Miele Hydromatic WT745 stuck on wash cycle? The tumble dry heater works fine. Any idea what the problem might be. I thought it could be heating element, but not sure. Turn the dial to start wash and it just doesn't move from the start? Kind Regards Rebecca.

@YoramPomer

7 жыл бұрын

super saiyan 3 goku - Probably not. Try washing without any heating. If the problem stays the same then it has nothing to do with the heater.

Top Video

Ganz tolles Video, man sieht schritt für schritt wie es gewechselt wird. Nur die Schrift mittig im Geschehen stört ein wenig

@YoramPomer

3 ай бұрын

Danke, ich schätze Ihr Feedback

At 3:09 you place the clip on the wrong location, compare it with the location of the old clip at 2:50. The clip has to be placed more towards the contacts. The marking that you see in the lime (3:09) comes from the holder clip fixed inside of the drum.

@YoramPomer

6 жыл бұрын

Deux Cent I don't agree and I don't think that it's important for the functionality of the clip

@deuxcent4625

5 жыл бұрын

Don't get into a huff when it is pointed out to you! I just wanted to draw your attention to something that would correct your movie (for the rest excellent). Viewers of your movie would then be better served. Look again to your tutorial at 2:50 and 3:09.

@George-vl4lm

3 жыл бұрын

@@deuxcent4625 that's correct the clip needs to be placed near the bend in the element towards the opening. The other clip inside the drum is fixed halfway inside and as you slide the element in, the inner most bend is guided through the internal clip. You can see the location of the internal clip by shining a torch through the drum perforations :-)

I find it impossible to push the new rubber sealing fully into the hole. Seams to need yet another 2 mm. Now I cannot pull the new rubber sealing out again. Should I have used some kind of grease on the rubber sealing before pushing the rubber sealing into the hole?

@YoramPomer

7 жыл бұрын

Slippery liquid that dries could have been helpful - But grease is not a good option. Don't try to pull it out - you will weaken the seal. just lock it in place and it should hold.

@aaaaa5272

7 жыл бұрын

What I did: I pulled it out again as 'gently' as I could, it was not as hard as I had expected. Advised by a friend, I put the rubber sealing in 60 degree water which made it more soft. After that I added a few drops of liquid hand soap around the rubber sealing. Finally it was very easy to put rubber sealing in place.

@YoramPomer

7 жыл бұрын

Soap is a good option. I hope that your washing machine is working fine now

I have a W833 with 22 years of around 7 uses per week and still looks new. Only ever problem was a door seal (which we broke trapping towel in door) easy to replace. Now we have a heating problem sometimes getting warm sometimes seems not to have heated. I'm wondering if this is the element or the sensor or something else? I'm thinking just replace the sensor first. I would appreciate any advice.

@YoramPomer

Жыл бұрын

I would try to replace the heating element because after 22 years it can only do good to the washing machine. You will also find lots of dirt down there, so that it will certainly improve the heating efficiency of your washing machine. Its hard to say if this is the problem. It can also be the sensor or even the electronics.

@Iazzaboyce

Жыл бұрын

@@YoramPomer I replaced drain pump with a good used one, replaced motor brushes which were down to 5mm, replaced both shocks with new ones, replaced heating element (old one and drum interior like new as soft water area). Now machine runs well, but has rinse light rapid flashing. Rinse light was flashing before I started think it might be related to spraying switch cleaner around main control switch?? As this is the only thing I did. I would appreciate any ideas.

@YoramPomer

Жыл бұрын

@@Iazzaboyce Did you try cleaning the entire drain system? Its so easy. You press the spring that hold the rubber in place and take it apart. The entire system needs to be clean. If this problem stays, than maybe you have a problem with the pump. Again - get it cleaned and make sure that nothing is blocking its rotation.

How do you find out which part you need for your machine?

@YoramPomer

3 жыл бұрын

I agree that it’s not easy. I usually look for the Miele schema breakdown . Sometimes I do the opposite by looking at a website that writes very clearly to which device the product that they are selling is compatible. Those that sell at Ebay Germany usually provide this information. Alternatively, do a Google search.

Where can I find the heater in miele wkf131wps, front or back please?

@YoramPomer

Жыл бұрын

I am not familiar with your model. In my model it was at the right side.

Smoke is coming what is the problem

The heater is in the same place in all Miele washing machines?

@YoramPomer

2 жыл бұрын

I don’t know. I am only familiar with the machines that I own.

@spotlight761

2 жыл бұрын

@@YoramPomer Do you know if it is the same for the Miele Softtronic W6546?

hi is there any one who could help me with advise on a miele washing machines? I have a 2240 washing machine with a fault! the heater element is permanently on! the only way you can turn it off is by the plug at the wall! you can turn the machine of with the off switch and it will turn off, but the element will still burn its self out!! any advice, apart from buy a new machine :)

@YoramPomer

6 жыл бұрын

sparkynight73 Your description sound like a satire because it's technically not possible :-)

@sparkynight73

6 жыл бұрын

unfortunately it is possible because its happening to me, blown two elements already! only way to stop it is to turn it off at wall!!!

@YoramPomer

6 жыл бұрын

sparkynight73 Sorry for my doubt... I have no idea how this can happen . Miele is known for its error prevention logic in its devices, this is why it sounded so untruthful. Best of luck in your research for a solution

@YoramPomer

6 жыл бұрын

On second thought, it could either be a faulty relay ( or triac, as I am not familiar with this machine) that is permanently closed or the logic board. You can easily measure this - be carful of the high voltage! If it's the relay, then the fix is very straight forward. if its the logic board, then I would send it to someone that knows how to repair it.

@sparkynight73

6 жыл бұрын

i will check the relay thanks

Great video, thank you. But I have a question: aren't Miele washing machines built to last 20 years, or is that just marketing hype?

@hodgymac

3 жыл бұрын

we have have Miele Novo w842 for over 20 years - my wife and I have 5 kids, it has done a wash at least once a day every day since we bought it in 1999 - i have had to replace a few things, but still going strong (i just need to replace the heater element, hence why i am here)

@garethsnaim8174

3 жыл бұрын

Yes its hype.

what is with music. and why? othervise thanks for video

@YoramPomer

3 ай бұрын

Back then , music was a must, today its more about the spoken words. Thanks for your feedback.

You better use 2-3 times a year citric acid

@YoramPomer

6 жыл бұрын

Frau M why?

@milangal8807

2 жыл бұрын

@@YoramPomer Yeah, at maximum temperature and without any clothing inside. Because (as you can see) the machine is very dirty inside, even the old heating element was very dirty when you take him out from the outer drum. You probably don't wash at higher temperatures than 40 degrees of Celsius and the mud (or how to name it) caused the heater to burn out. The heat that builds up in the heater body cannot be transferred to the water due to dirt and limescale, and the heater burns out. Wash at least once a month at a minimum of 60 degrees of Celsius using a classic powder detergent, or at least 3-4 times a year run a cotton program at the highest temperature (95 C) with 200 - 300g of citric acid (of course without laundry). 😉

@YoramPomer

2 жыл бұрын

@@milangal8807 You are probably right. Maybe there is a washing machine detergent that leaves less rest overs.

what a terrible design

@YoramPomer

7 жыл бұрын

I don't agree. Although having screws that tighten the heater to the drum feels like a better construction, there are good reasons that Miele decided on this solution (Miele is not a company that saves on Quality): 1. You must replace the sealing with the heater element because by taking out the old one, you will make it unusable. 2. The are no screws that can get stuck or rust, so that you will always be able to remove the old heater, even after 20 years of use. 3. The rubber seal gets tighter over time because of the heat and the movement of the machine. Whereas screws can get lose over time. 4. The quality of the parts is so high, that if you follow the instructions, then success is guaranteed