Today's vehicle: 1984 GMC Jimmy with a 350 engine. Tools Needed -Eye Protection -Basic Socket Set with Extensions -New Starter -Brakleen
Жүктеу.....
Пікірлер: 117
@EddieC20008 ай бұрын
Best K5 Blazer repair video I've seen yet. Such detail is rarely seen on repair video.
@douglasphillips243 ай бұрын
My son removed the old starter from 77 C10 and I went and installed it just by factory wire ends . I had everything right except the small terminal was on wrong stud nearest frame that gets used on older vehicles only. This was only video showing taking wires off so thanks . Awesome video.
@izmashing5993
3 ай бұрын
I can tou explain better? I think i put the small wire on wrong terminal?? Where does it go?
@codemang873 жыл бұрын
Nice video. Its very helpful the you describe where each wire connects to. Got my starter changed in my 85 k1500 in 30 mins following this video.
@MechanicLife
3 жыл бұрын
Glad it helped you out!
@mcelyeajoe664 жыл бұрын
I'm so old that I forgot which terminal to bolt the single wire to. The young man who wired in the starter for me put the small wire on the R side and I thought that was wrong. Your video showed me that I had not forgotten everything. THANK YOU.
@MechanicLife
4 жыл бұрын
Very cool!
@christinaturner38452 жыл бұрын
Thank you for such a good video! So many out there that are not easy to see what is being done!
@lukelangbehn5432
2 жыл бұрын
Most Welcome!
@duncanp19875 жыл бұрын
Hey! Thank you for this video. I took this out on my 1979 M1009 Military Blazer, but then forgot where the smallest wire connected to! I searched it up, and your video showed me exactly where I was to wire it. Thanks again!
@MechanicLife
5 жыл бұрын
Glad you got er! Military with the diesel! Very cool truck man.
@NoNo-vg9ts
4 жыл бұрын
Duncan Peterman I know it’s been a while but how did u remove it. The diff is crazy in the way. I took off 2 screws I think at 8mm holding the starter. Then 2 15mm which look to be to the block. But mine won’t come off. And the terminal ones (not the batteries ) I can’t even reach. Even smacked her with a hammer lightly. What am I missing
@sebastianpalacio80723 жыл бұрын
Such a great video, I’m planning on changing my starter later on today!
@MechanicLife
2 жыл бұрын
THanks!
@radwizard2 жыл бұрын
Right on! Excellent video and demonstration.
@MechanicLife
2 жыл бұрын
Thanks!
@michaelbliss19762 жыл бұрын
I have a 76 El Camino as my first car and the starter been giving me trouble, been wacking on it to start sometimes after school. Now it won’t engage so I’m gonna install a new one tomorrow. Thank you for the vid! Very simple and clear!
@michaelbliss1976
2 жыл бұрын
I have a jounce bar and the exhaust in the way.. no possible way without moving the bar but I’ll attempt. Gonna have to give her another try…
@zbmccarter
9 ай бұрын
@@michaelbliss1976 I know this is an old comment, but I'm going to put this here for anyone who has the same problem with replacing a starter on a late 80s model El Camino/ caballero. It is possible to get the starter in without moving the 2 metal bars/ exhaust that are inexplicably placed right in the way of the starter. You have to tilt the starter to the perfect angle to slide it through the gap, then readjust it once it is above the bars, line it up with the holes, and pray you can get at least one bolt to connect while you're holding the 20 lb starter in place with one hand/ tightening with the other. This is not an easy task, but it is possible.
@rswindello3 жыл бұрын
Great video. Very well explained. Thanks a lot
@MechanicLife
3 жыл бұрын
Thanks!
@dhgcrack3r1113 жыл бұрын
“Always something wrong with this stupid thing” amen. 1pm on a Sunday (my day off) and I don’t have a starter. Shouldn’t have missed church this morning lol.
@derekhoyle1903 жыл бұрын
Thanks for the video. Helped me with mine.
@MechanicLife
3 жыл бұрын
Great to hear!
@kevinrichards32882 жыл бұрын
1991 was the last year for those second generation Blazers & Jimmys, & same with the seventh generation Suburbans & third generation C/K series pickups "only the crew cabs".
@RealLifeFinance4 ай бұрын
Excellent video
@christopherdavid93572 жыл бұрын
Just what I needed.
@MechanicLife
2 жыл бұрын
Great!
@wmforester0073 жыл бұрын
Thank you! Goodish video!
@josiahkaplan8419
2 жыл бұрын
Crappy ish response!
@sirjohnahayfalcon3 жыл бұрын
Excellent video I have 87 suburban with a slow crank and sometimes so slow it won’t crank. Some times I’ll hit the gas when I try to start wich helps sometimes
@sirjohnahayfalcon
3 жыл бұрын
Does my issue sound like fuel injector?
@MechanicLife
3 жыл бұрын
Need a little more info. Does it only happen when its on a cold start? Could be a bad battery/ bad starter. etc.
@sirjohnahayfalcon
3 жыл бұрын
@@MechanicLife usually happens on hot start.. But on every cold start it turns like normal but doesnt start the engine its always starts on the second try
@dleathersdl Жыл бұрын
Thanks this was helpful
@MechanicLife
Жыл бұрын
You bet!
@mashooga3 жыл бұрын
Hey our kind of rigs including Ford Broncos were built to break down that's the fun of it LOL
@MechanicLife
3 жыл бұрын
Right!
@mashooga
3 жыл бұрын
@@MechanicLife I forgot to say I fixed my starter the other day, it was a loose wire that was causing Havoc now it is purring like a kitten, well as much of a purrr it can possibly do LOL
@MechanicLife
3 жыл бұрын
Always like a cheap fix! Awesome
@zgamer94423 жыл бұрын
Thank you so much
@MechanicLife
3 жыл бұрын
You bet. Thanks for the awesome comments!!
@starman94584 жыл бұрын
My grandfather has a 1977 Chevy K20 350 unleaded built on with 1982 and 1984 parts and the starter is going out on it.
@davidzon98562 жыл бұрын
Very nice
@PrestonGarvey692 жыл бұрын
It's the same starter on my 81' Chevy rwd C10. I made the mistake of letting a lengthy battery wire hang and touch the ground wire to the solenoid and it kept jumping the motor once I started it and had to disconnect the battery to shut it off
@angelc82715 жыл бұрын
Hey man great video! I have a 1977 c10 with a pretty bad worn gear so I'm looking to just replace the whole starter, but where did you get your starter and what brand is it? I'm looking for something fairly cheap but that will work consistently
@MechanicLife
5 жыл бұрын
I got it at Autozone. It was a Duralast Gold.
@mashooga3 жыл бұрын
I'm having a problem with my starter recently, of course , getting ready to go shim it, better I think, right now...lol
@jerejere694 жыл бұрын
Thanks for showing how its supposed to be so I can compare my old one. to your new one and figure out if my starter is bad.
@jamescale62824 жыл бұрын
I have a question if anyone can answer it I have a 76 c20 it has a 350 out of a 80’s model I’m guessing and this morning it didn’t want to start unlike this video mine clicks only once so is there a second solenoid on the body somewhere that I can try replacing before I have to pull my right side long tube header to get to the starter solenoid?
@henrymccarty80143 жыл бұрын
Is this the same in a 88 chevy s10 pickup??
@tylersim55012 жыл бұрын
@MechanicLife Were the nose cone plates entirely different on the new vs. the old starter? They appear to be more rounded / beveled on the new one, and the old one seems to be flat / straight. Correct? Should it matter? Did you have to specify the nose cone shape when ordering? Thanks -
@MechanicLife
2 жыл бұрын
Yes they were a bit different. I didnt have to specify when I had Autozone get the part.
@xezavierwestbrook9271 Жыл бұрын
The wire that was connected with the battery wire is that also the ignition wire and are there two ignition wires on the starter
@rafa150311 ай бұрын
Not sure if you will read this but i am stuck right now just rebuilt a motor and the starter connections were cut but i only have one thick red wire coming from fuse box that goes to to a post on firewall before the starter, a purple wire and the large 12v wire, where should the third one be coming from any idea? thanks for the video anyway!
@MechanicLife
11 ай бұрын
I read this and am looking into it right now:)
@MechanicLife
11 ай бұрын
What year make and model?
@rafa1503
11 ай бұрын
@@MechanicLife Figured it out but appreciate the response! it was whats originally spliced from the fusebox to the purple starter wire ,alternator wires and the resister bulb before it.
@FlamingRayz Жыл бұрын
I’m working on a 1974 c10 and I just installed a new starter. Mine had 2 small wires and one went on each of the small studs. The motor was working and turning over the truck for the first couple tries but then it stopped and now all I get is one click and nothing else. Do you know what that could be?
@TheseBygones3 жыл бұрын
Which connections first
@mrbrocephus38493 жыл бұрын
I have a 1975 chevy caprice. When I staring it I have some grinding then it starts I hoping it just the start missing teeth vs the starter wheel. The grinding nose isn’t Constant ether 😅🥲
@jonhsmith2706
Жыл бұрын
What was it
@mashooga3 жыл бұрын
So I came back to ask you if your truck has another little arm like metal piece that goes from starter to body of truck to help with securing the starter in place to keep from it jumping around when truck driving in mountains, or whatever?
@MechanicLife
3 жыл бұрын
Nope. It just bolts directly up. Sometimes vehicles will have straps that go around to body of the starter though.
@yolo-qr2fq3 жыл бұрын
Does it matter if you put your ignition wires first or your 12v constant?
@timhaupt5270
3 жыл бұрын
No, the sequence on the stud does not matter.
@Biggpcam014 жыл бұрын
what did you have to move to get it out looks like the cross member and exhaust pipe on my 87 s15 is in the way
@montanamade1114
4 жыл бұрын
I didnt have to remove anything to get it out.
@mashooga
3 жыл бұрын
@@montanamade1114 hell no you don't, very easy to get to
@jonathanvasquez1088
3 жыл бұрын
Cameron Reed I just took my off my 85 gmc s15 and your right but I just wiggled it around until it came out
@BanCorporateOwnedHouses3 ай бұрын
Dude, how the hell do you wire a min starter onto these? I have that thick black wire and the red wire on one terminal, and it immediately engages the starter. Something is messef up, and I have no idea how to fix it.
@robertwaldron93834 жыл бұрын
Good video Thanks! Your speedometer only goes to 65?
@driger8884 жыл бұрын
no need to test fit with flywheel and shim?
@gabedramstad69174 жыл бұрын
I have a 82 c10 and it started just fine. I jumped a car and parked my pickup. A day later I turned the key all the lights turned on and when I went to start position nothing happened. No clicking no jittering just dead. Any suggestions?
@yolo-qr2fq
3 жыл бұрын
I'm having the same issue with a 1982 c30 dually with the 350. Accessories have power but no clicking. So my guess is ignition switch, starter, distributor, or wiring since it's been sitting for 8yrs and mice suck.
@gabedramstad6917
3 жыл бұрын
@@yolo-qr2fq I traced the wires from the starter back and it turns out I blew a fuse
@Roblu-k6u
3 жыл бұрын
15 fuse in the fuse box
@yolo-qr2fq
3 жыл бұрын
@@gabedramstad6917 okay. Would have a low voltage on the battery still make noise?
@gabedramstad6917
3 жыл бұрын
@@yolo-qr2fq nope the battery was fine. I looked ar the wired and saw I had some melted ones but the big problem was the fuse that has probably been on it since factory. I replaced that and it fired right up
@JessicaVasquez-n7o21 сағат бұрын
Where did you find the starter. I cannot find one for my 1985 chevy s10 blazer
@JessicaVasquez-n7o
21 сағат бұрын
I went to autozone and they are coming up with a totally different starter. Can you give me a part number?
@davidzon98562 жыл бұрын
How about wiring video on how to wire in starter alternator and ignition switch On1987GMC 454
@richardvelasquez27194 жыл бұрын
This is same for 85 caprice
@lisajimenez139 ай бұрын
You still have this truck ??
@westcoast29763 жыл бұрын
Do you have to used the shi shams
@MechanicLife
3 жыл бұрын
I didnt no.
@crimthegrim4 жыл бұрын
What size sockets?
@MechanicLife
4 жыл бұрын
I believe they are 13mm
@MechanicLife
4 жыл бұрын
Or a 15mm watching the video.
@panerenwanz36 Жыл бұрын
Mine clicks once but then stops what could this be
@MechanicLife
Жыл бұрын
Is the unit new or old? When they go bad a lot of times you will get the single click and then nothing.
@tl6352 Жыл бұрын
How many pounds was that starter
@mashooga3 жыл бұрын
Well here I go
@omellym7363
3 жыл бұрын
Did you get it changed out? I need to remove mine on my 80 C10
@MechanicLife
3 жыл бұрын
How'd it go!
@sirjohnahayfalcon2 жыл бұрын
Where is this starters ground connection on 350 . I see a positive big wire from solenoid to battery but no dedicated ground?
@obs_vell4393 ай бұрын
U can gain muscle by lifting a gmc starter for trucks lol
@kblopp4 жыл бұрын
Sounds like a half dead battery to me.
@MechanicLife
4 жыл бұрын
Brand new at that time. Was getting rid of a bunch of old parts.
@mashooga
3 жыл бұрын
@@MechanicLife everyone goes to battery first..
@connorkloepfer32672 жыл бұрын
Really would have been helpful if you showed where things were with the video rather than just cutting to the part
@Joseph-jp4oh Жыл бұрын
Could you contact me please I have a question
@MechanicLife
Жыл бұрын
Whats up?
@gilbertgrape99694 жыл бұрын
Hey Luke, I have a C1500 Chevy pickup 1988 very similar to the blazer in the video the starter isn’t completely flush with the flywheel cover but my truck still starts, is it normal for the starter to not be completely flush on these vehicles?
@MechanicLife
4 жыл бұрын
As long as you are square with the flywheel on the mount you are good. Do you have spacers installed? How does it sound on startup? Anything weird
@gilbertgrape9969
4 жыл бұрын
Lukes Garage Nope, no spacers, haven’t gotten under it and really listened to it yet but from the cab it sounds fine.
@MechanicLife
4 жыл бұрын
It doesnt sound strange to me at all. How wide is the gap?
@gilbertgrape9969
4 жыл бұрын
Lukes Garage probably a quarter inch, I should mention that the flywheel cover is a bit beat up from age so that might have something to do with it.
@gilbertgrape9969
4 жыл бұрын
Lukes Garage I’ve also noticed a bit of a “whirring” noise after starting but it goes away after a second
Пікірлер: 117
Best K5 Blazer repair video I've seen yet. Such detail is rarely seen on repair video.
My son removed the old starter from 77 C10 and I went and installed it just by factory wire ends . I had everything right except the small terminal was on wrong stud nearest frame that gets used on older vehicles only. This was only video showing taking wires off so thanks . Awesome video.
@izmashing5993
3 ай бұрын
I can tou explain better? I think i put the small wire on wrong terminal?? Where does it go?
Nice video. Its very helpful the you describe where each wire connects to. Got my starter changed in my 85 k1500 in 30 mins following this video.
@MechanicLife
3 жыл бұрын
Glad it helped you out!
I'm so old that I forgot which terminal to bolt the single wire to. The young man who wired in the starter for me put the small wire on the R side and I thought that was wrong. Your video showed me that I had not forgotten everything. THANK YOU.
@MechanicLife
4 жыл бұрын
Very cool!
Thank you for such a good video! So many out there that are not easy to see what is being done!
@lukelangbehn5432
2 жыл бұрын
Most Welcome!
Hey! Thank you for this video. I took this out on my 1979 M1009 Military Blazer, but then forgot where the smallest wire connected to! I searched it up, and your video showed me exactly where I was to wire it. Thanks again!
@MechanicLife
5 жыл бұрын
Glad you got er! Military with the diesel! Very cool truck man.
@NoNo-vg9ts
4 жыл бұрын
Duncan Peterman I know it’s been a while but how did u remove it. The diff is crazy in the way. I took off 2 screws I think at 8mm holding the starter. Then 2 15mm which look to be to the block. But mine won’t come off. And the terminal ones (not the batteries ) I can’t even reach. Even smacked her with a hammer lightly. What am I missing
Such a great video, I’m planning on changing my starter later on today!
@MechanicLife
2 жыл бұрын
THanks!
Right on! Excellent video and demonstration.
@MechanicLife
2 жыл бұрын
Thanks!
I have a 76 El Camino as my first car and the starter been giving me trouble, been wacking on it to start sometimes after school. Now it won’t engage so I’m gonna install a new one tomorrow. Thank you for the vid! Very simple and clear!
@michaelbliss1976
2 жыл бұрын
I have a jounce bar and the exhaust in the way.. no possible way without moving the bar but I’ll attempt. Gonna have to give her another try…
@zbmccarter
9 ай бұрын
@@michaelbliss1976 I know this is an old comment, but I'm going to put this here for anyone who has the same problem with replacing a starter on a late 80s model El Camino/ caballero. It is possible to get the starter in without moving the 2 metal bars/ exhaust that are inexplicably placed right in the way of the starter. You have to tilt the starter to the perfect angle to slide it through the gap, then readjust it once it is above the bars, line it up with the holes, and pray you can get at least one bolt to connect while you're holding the 20 lb starter in place with one hand/ tightening with the other. This is not an easy task, but it is possible.
Great video. Very well explained. Thanks a lot
@MechanicLife
3 жыл бұрын
Thanks!
“Always something wrong with this stupid thing” amen. 1pm on a Sunday (my day off) and I don’t have a starter. Shouldn’t have missed church this morning lol.
Thanks for the video. Helped me with mine.
@MechanicLife
3 жыл бұрын
Great to hear!
1991 was the last year for those second generation Blazers & Jimmys, & same with the seventh generation Suburbans & third generation C/K series pickups "only the crew cabs".
Excellent video
Just what I needed.
@MechanicLife
2 жыл бұрын
Great!
Thank you! Goodish video!
@josiahkaplan8419
2 жыл бұрын
Crappy ish response!
Excellent video I have 87 suburban with a slow crank and sometimes so slow it won’t crank. Some times I’ll hit the gas when I try to start wich helps sometimes
@sirjohnahayfalcon
3 жыл бұрын
Does my issue sound like fuel injector?
@MechanicLife
3 жыл бұрын
Need a little more info. Does it only happen when its on a cold start? Could be a bad battery/ bad starter. etc.
@sirjohnahayfalcon
3 жыл бұрын
@@MechanicLife usually happens on hot start.. But on every cold start it turns like normal but doesnt start the engine its always starts on the second try
Thanks this was helpful
@MechanicLife
Жыл бұрын
You bet!
Hey our kind of rigs including Ford Broncos were built to break down that's the fun of it LOL
@MechanicLife
3 жыл бұрын
Right!
@mashooga
3 жыл бұрын
@@MechanicLife I forgot to say I fixed my starter the other day, it was a loose wire that was causing Havoc now it is purring like a kitten, well as much of a purrr it can possibly do LOL
@MechanicLife
3 жыл бұрын
Always like a cheap fix! Awesome
Thank you so much
@MechanicLife
3 жыл бұрын
You bet. Thanks for the awesome comments!!
My grandfather has a 1977 Chevy K20 350 unleaded built on with 1982 and 1984 parts and the starter is going out on it.
Very nice
It's the same starter on my 81' Chevy rwd C10. I made the mistake of letting a lengthy battery wire hang and touch the ground wire to the solenoid and it kept jumping the motor once I started it and had to disconnect the battery to shut it off
Hey man great video! I have a 1977 c10 with a pretty bad worn gear so I'm looking to just replace the whole starter, but where did you get your starter and what brand is it? I'm looking for something fairly cheap but that will work consistently
@MechanicLife
5 жыл бұрын
I got it at Autozone. It was a Duralast Gold.
I'm having a problem with my starter recently, of course , getting ready to go shim it, better I think, right now...lol
Thanks for showing how its supposed to be so I can compare my old one. to your new one and figure out if my starter is bad.
I have a question if anyone can answer it I have a 76 c20 it has a 350 out of a 80’s model I’m guessing and this morning it didn’t want to start unlike this video mine clicks only once so is there a second solenoid on the body somewhere that I can try replacing before I have to pull my right side long tube header to get to the starter solenoid?
Is this the same in a 88 chevy s10 pickup??
@MechanicLife Were the nose cone plates entirely different on the new vs. the old starter? They appear to be more rounded / beveled on the new one, and the old one seems to be flat / straight. Correct? Should it matter? Did you have to specify the nose cone shape when ordering? Thanks -
@MechanicLife
2 жыл бұрын
Yes they were a bit different. I didnt have to specify when I had Autozone get the part.
The wire that was connected with the battery wire is that also the ignition wire and are there two ignition wires on the starter
Not sure if you will read this but i am stuck right now just rebuilt a motor and the starter connections were cut but i only have one thick red wire coming from fuse box that goes to to a post on firewall before the starter, a purple wire and the large 12v wire, where should the third one be coming from any idea? thanks for the video anyway!
@MechanicLife
11 ай бұрын
I read this and am looking into it right now:)
@MechanicLife
11 ай бұрын
What year make and model?
@rafa1503
11 ай бұрын
@@MechanicLife Figured it out but appreciate the response! it was whats originally spliced from the fusebox to the purple starter wire ,alternator wires and the resister bulb before it.
I’m working on a 1974 c10 and I just installed a new starter. Mine had 2 small wires and one went on each of the small studs. The motor was working and turning over the truck for the first couple tries but then it stopped and now all I get is one click and nothing else. Do you know what that could be?
Which connections first
I have a 1975 chevy caprice. When I staring it I have some grinding then it starts I hoping it just the start missing teeth vs the starter wheel. The grinding nose isn’t Constant ether 😅🥲
@jonhsmith2706
Жыл бұрын
What was it
So I came back to ask you if your truck has another little arm like metal piece that goes from starter to body of truck to help with securing the starter in place to keep from it jumping around when truck driving in mountains, or whatever?
@MechanicLife
3 жыл бұрын
Nope. It just bolts directly up. Sometimes vehicles will have straps that go around to body of the starter though.
Does it matter if you put your ignition wires first or your 12v constant?
@timhaupt5270
3 жыл бұрын
No, the sequence on the stud does not matter.
what did you have to move to get it out looks like the cross member and exhaust pipe on my 87 s15 is in the way
@montanamade1114
4 жыл бұрын
I didnt have to remove anything to get it out.
@mashooga
3 жыл бұрын
@@montanamade1114 hell no you don't, very easy to get to
@jonathanvasquez1088
3 жыл бұрын
Cameron Reed I just took my off my 85 gmc s15 and your right but I just wiggled it around until it came out
Dude, how the hell do you wire a min starter onto these? I have that thick black wire and the red wire on one terminal, and it immediately engages the starter. Something is messef up, and I have no idea how to fix it.
Good video Thanks! Your speedometer only goes to 65?
no need to test fit with flywheel and shim?
I have a 82 c10 and it started just fine. I jumped a car and parked my pickup. A day later I turned the key all the lights turned on and when I went to start position nothing happened. No clicking no jittering just dead. Any suggestions?
@yolo-qr2fq
3 жыл бұрын
I'm having the same issue with a 1982 c30 dually with the 350. Accessories have power but no clicking. So my guess is ignition switch, starter, distributor, or wiring since it's been sitting for 8yrs and mice suck.
@gabedramstad6917
3 жыл бұрын
@@yolo-qr2fq I traced the wires from the starter back and it turns out I blew a fuse
@Roblu-k6u
3 жыл бұрын
15 fuse in the fuse box
@yolo-qr2fq
3 жыл бұрын
@@gabedramstad6917 okay. Would have a low voltage on the battery still make noise?
@gabedramstad6917
3 жыл бұрын
@@yolo-qr2fq nope the battery was fine. I looked ar the wired and saw I had some melted ones but the big problem was the fuse that has probably been on it since factory. I replaced that and it fired right up
Where did you find the starter. I cannot find one for my 1985 chevy s10 blazer
@JessicaVasquez-n7o
21 сағат бұрын
I went to autozone and they are coming up with a totally different starter. Can you give me a part number?
How about wiring video on how to wire in starter alternator and ignition switch On1987GMC 454
This is same for 85 caprice
You still have this truck ??
Do you have to used the shi shams
@MechanicLife
3 жыл бұрын
I didnt no.
What size sockets?
@MechanicLife
4 жыл бұрын
I believe they are 13mm
@MechanicLife
4 жыл бұрын
Or a 15mm watching the video.
Mine clicks once but then stops what could this be
@MechanicLife
Жыл бұрын
Is the unit new or old? When they go bad a lot of times you will get the single click and then nothing.
How many pounds was that starter
Well here I go
@omellym7363
3 жыл бұрын
Did you get it changed out? I need to remove mine on my 80 C10
@MechanicLife
3 жыл бұрын
How'd it go!
Where is this starters ground connection on 350 . I see a positive big wire from solenoid to battery but no dedicated ground?
U can gain muscle by lifting a gmc starter for trucks lol
Sounds like a half dead battery to me.
@MechanicLife
4 жыл бұрын
Brand new at that time. Was getting rid of a bunch of old parts.
@mashooga
3 жыл бұрын
@@MechanicLife everyone goes to battery first..
Really would have been helpful if you showed where things were with the video rather than just cutting to the part
Could you contact me please I have a question
@MechanicLife
Жыл бұрын
Whats up?
Hey Luke, I have a C1500 Chevy pickup 1988 very similar to the blazer in the video the starter isn’t completely flush with the flywheel cover but my truck still starts, is it normal for the starter to not be completely flush on these vehicles?
@MechanicLife
4 жыл бұрын
As long as you are square with the flywheel on the mount you are good. Do you have spacers installed? How does it sound on startup? Anything weird
@gilbertgrape9969
4 жыл бұрын
Lukes Garage Nope, no spacers, haven’t gotten under it and really listened to it yet but from the cab it sounds fine.
@MechanicLife
4 жыл бұрын
It doesnt sound strange to me at all. How wide is the gap?
@gilbertgrape9969
4 жыл бұрын
Lukes Garage probably a quarter inch, I should mention that the flywheel cover is a bit beat up from age so that might have something to do with it.
@gilbertgrape9969
4 жыл бұрын
Lukes Garage I’ve also noticed a bit of a “whirring” noise after starting but it goes away after a second