How to Replace a Porch Column | Ask This Old House

Тәжірибелік нұсқаулар және стиль

In this video, general contractor Tom Silva shows a homeowner how to remove and repair the rot eating away at his porch’s support post.
SUBSCRIBE to This Old House: bit.ly/SubscribeThisOldHouse.
Tom Silva lends some support to a homeowner suffering under a rotted porch post. Tom and the homeowner dig into the rotten post base to find the issue, and then get to work removing the affected wood. Next, Tom shows the homeowner how to mill new components from a recycled, water-resistant material before putting everything back together for caulk and paint.
Skill: ⅗
Cost: Around $200
Time: 4 hours
Materials:
Scrap 4x4 post [thd.co/3LdAFOW]
Rice hull boards [bit.ly/3gxgYn0] (or other weather-resistant wood)
Fast-setting epoxy or polyurethane glue [amzn.to/3GxDCq8]
Shims [amzn.to/35Q4e8V]
Sandpaper [amzn.to/3gwRxSx]
Screws [thd.co/30fYbYV]
Construction adhesive [amzn.to/3B2BDZP]
Tools:
Bottle jack [amzn.to/3HzFXSx]
Reciprocating saw with a 10-inch blade [amzn.to/335g6mx]
Miter or circular saw [amzn.to/3gydzVb]
Level [amzn.to/3uFNXxE]
Scribes [amzn.to/3guQVgw]
Pencil [amzn.to/3owpCGU]
Bandsaw or table saw [amzn.to/3HC7h2u]
Brad nailer [amzn.to/3oshvLq]
Jigsaw [amzn.to/34LnpR2]
Router and bits [amzn.to/34FK5lm]
Sander [amzn.to/3GE64X7]
Drill and spade bits [amzn.to/3ryQdFi]
Impact driver and driver bits [amzn.to/3B6qJlD]
Caulk gun [amzn.to/3ovHYb3]
How To Repair Rotted Porch Post
1. Place the 4x4 post and bottle jack underneath a header on the porch and lift the porch roof slightly until the post is free from the ground. Remove any of the rotted material by hand, but do not reach under the post for safety’s sake.
2. Use a reciprocating saw fitted with a 10-inch wood cutting blade to remove the rot. Be sure to make this cut as level and evenly as possible.
3. Cut a piece of the rice hull board or wood to the correct square dimensions. Often, this is 2 or 3 inches wider than the post’s diameter. It might be necessary to double this block with an additional layer of wood to match the other posts. If that’s the case, glue the two blocks together with a fast-setting adhesive.
4. Place the block under the post and level it side to side and front to back with shims. Once level, place small strips of wood along the perimeter on top of the block. Use the scribes to mark the pitch of the surface on these strips. Be sure to mark each strip and its location as you go. Cut the strips along the scribe lines on a bandsaw or table saw before gluing them to the block with the adhesive.
5. Use the scribes to draw a circle of the appropriate size on a piece of the rice hull board or wood. For thicker profiles, screw two layers of the wood together before cutting along the circle with the jigsaw. Sand both layers smooth and evenly, and add a detail with a router, if desired.
6. Repeat the last step, but with a smaller circle to create a cascading profile. Drill a ¾-inch hole in the middle of each of these circles to allow for airflow and prevent future rot.
7. Assemble the pieces under the post. Before lowering the post, squeeze a bead of construction adhesive between the post and the new base.
8. Lower the jack slowly, allowing the post to settle on the base and squeeze the excess construction adhesive out. Smooth the excess adhesive before allowing it to dry.
9. At each corner, drive a screw from the top-most layer of the base into the bottom base. Fill the screw holes and paint.
Looking for more step by step guidance on how to complete projects around the house? Join This Old House Insider to stream over 1,000 episodes commercial-free: bit.ly/2GPiYbH
Plus, download our FREE app for full-episode streaming to your connected TV, phone or tablet: www.thisoldhouse.com/pages/st...
About Ask This Old House TV:
From the makers of This Old House, America’s first and most trusted home improvement show, Ask This Old House answers the steady stream of home improvement questions asked by viewers across the United States. Covering topics from landscaping to electrical to HVAC and plumbing to painting and more. Ask This Old House features the experts from This Old House, including general contractor Tom Silva, plumbing and heating expert Richard Trethewey, landscape contractor Jenn Nawada, master carpenter Norm Abram, and host Kevin O’Connor. Ask This Old House helps you protect and preserve your greatest investment-your home.
Follow This Old House and Ask This Old House:
Facebook: bit.ly/ThisOldHouseFB
Twitter: bit.ly/AskTOHTwitter
Pinterest: bit.ly/ThisOldHousePinterest
Instagram: bit.ly/AskTOHIG
How to Replace a Porch Column | Ask This Old House
/ thisoldhouse

Пікірлер: 158

  • @michaelcarroll991
    @michaelcarroll9912 жыл бұрын

    Man I wish I could sit down with Tom Silva and just pick his mind. Guy is an Encyclopedia of woodworking.

  • @ryk3899

    @ryk3899

    2 жыл бұрын

    Same. However i can't forgive him for securing loose floorb by driving screws through the carpet

  • @mistereric416

    @mistereric416

    2 жыл бұрын

    @@ryk3899 Link?

  • @ryk3899

    @ryk3899

    2 жыл бұрын

    @Eric K find it yourself

  • @davidquinn6161

    @davidquinn6161

    2 жыл бұрын

    @@ryk3899 I've had good results doing that using O'Beery's Squeak No More products. Worked well thru carpet and bare floor.

  • @doug876

    @doug876

    2 жыл бұрын

    @@ryk3899 Did he use the screws that are designed to do exactly what you described? Because if so, then he did it exactly correct...

  • @amoni1959
    @amoni19592 жыл бұрын

    The guy raking leaves in the background was the real star.

  • @Engineer9736

    @Engineer9736

    2 жыл бұрын

    Did you just assume its gender

  • @JordanG123

    @JordanG123

    2 жыл бұрын

    @@Engineer9736 one joke

  • @Engineer9736

    @Engineer9736

    2 жыл бұрын

    @@JordanG123 😜

  • @WannaBeHocker
    @WannaBeHocker2 жыл бұрын

    A true professional vacuum cleaner operator here! 5:15 ......🤣🤣🤣

  • @sparky88xx

    @sparky88xx

    2 жыл бұрын

    Yes, he sucks at sucking. Also, why vacuum outdoors?

  • @bearg4019
    @bearg40192 жыл бұрын

    I've been a fan for 38 years..I never get tired watching ..

  • @tylerdurden7387
    @tylerdurden73872 жыл бұрын

    Love watching Tommy. Such an unbelievable craftsman

  • @malikdigger4544
    @malikdigger45442 жыл бұрын

    That's why TOH has been favorite home improvement tv show since great projects like this porch column base repair & other helpful tips from the pros. Tom, Richard,Norm,Nathan & new member Jenn

  • @dede13295
    @dede132952 жыл бұрын

    Always pleasure watching Tom work...:)

  • @res00xua
    @res00xua2 жыл бұрын

    Love the show the magazine and the KZread videos. I have learned a great deal watching for decade’s. Thanks

  • @stevendavanna
    @stevendavanna2 жыл бұрын

    Love it when I get a video from this old house featuring Tommy or Nathan

  • @davem6685
    @davem66852 жыл бұрын

    Tommy is such a wealth of knowledge. The handyman business is growing due to guys like Sam and there’s lots of them out there.

  • @rockerpat1085

    @rockerpat1085

    Жыл бұрын

    I Make My Living Off Sam's!!! The Problem Is Society Valves The Sam's More Than The Tom's!!!

  • @PJJ196
    @PJJ1962 жыл бұрын

    So happy to see some fresh content

  • @olgainesmedina5974
    @olgainesmedina59742 жыл бұрын

    Excelente trabajo. Me fascinó. Gracias 🙏🙏💯

  • @mypassion830
    @mypassion8302 жыл бұрын

    I love this program I grew up watching it

  • @yazeed3881
    @yazeed3881 Жыл бұрын

    I need to replace the 4 2x4 posts inside my front porch column and seeing this video made it look easy

  • @JEK
    @JEK2 жыл бұрын

    Tommy is the man, he can fix anything!

  • @kalijasin

    @kalijasin

    2 жыл бұрын

    Tom Silva is a master of all trades. He's a joiner, carpenter, cabinetmaker, woodworker, framer, etc.

  • @user-jx8ho3mw8k
    @user-jx8ho3mw8k3 ай бұрын

    Tom is the man!

  • @RobertLeBlancPhoto
    @RobertLeBlancPhoto2 жыл бұрын

    Sammy Pockets did a great job supervising.

  • @vazz22
    @vazz222 жыл бұрын

    Awesome Project!

  • @twitchtwitch9006
    @twitchtwitch90062 жыл бұрын

    great video . thank you for this.

  • @tj_gsomething_
    @tj_gsomething_2 жыл бұрын

    I hope they did the other side as well. Eventually the other side will go, why not cut identical pieces and just do both since it's so easy!

  • @willpall

    @willpall

    2 жыл бұрын

    Ask This Old House always does this. I think the idea is the homeowner has now learned what they need to do, and will tackle the rest of it themselves.

  • @rupe53

    @rupe53

    2 жыл бұрын

    ... for all we know, they did do the other side, but it's not shown in this shortened clip.

  • @davidredpath4781
    @davidredpath47812 жыл бұрын

    I could watch Tommy for hours

  • @JoseCabrera-wx6ur
    @JoseCabrera-wx6ur2 жыл бұрын

    Me gusta mucho sus trabajos

  • @devinbraun1852
    @devinbraun18526 ай бұрын

    I think this technique is going to work to repair 4-5 column bases at my brother and sister-in-law’s.

  • @the_realJP_
    @the_realJP_11 ай бұрын

    Tommy always makes it look so simple. How did he cut the bottom boards that he scribed though?

  • @beaker2k
    @beaker2k2 жыл бұрын

    Dude just has his hands in his pockets the whole time....thanks for helping bro

  • @dingdongmagee

    @dingdongmagee

    2 жыл бұрын

    Lol

  • @DetroitFlipKing

    @DetroitFlipKing

    2 жыл бұрын

    🤣

  • @WannaBeHocker

    @WannaBeHocker

    2 жыл бұрын

    But that vacuum action at 5:15 was something else

  • @jeffboelter1409

    @jeffboelter1409

    2 жыл бұрын

    There are some, that's the most you can expect.

  • @PJJ196

    @PJJ196

    2 жыл бұрын

    ?? No more than any other person they’ve had on the show

  • @egg110905
    @egg1109052 жыл бұрын

    Oh Tommy!

  • @romulogomes9831
    @romulogomes98318 ай бұрын

    Ecelente jobs! USA

  • @troykruse5161
    @troykruse51612 жыл бұрын

    Forgot to show how he made those pieces level after he scribed them

  • @CU96821
    @CU968214 ай бұрын

    Great work... But I fear that a considerable wind will rip the porch roof off because the column is not secured to the foundation!

  • @Russellviews

    @Russellviews

    10 күн бұрын

    Mine are not secured and never have been, house built in 1880. The weight of the roof should keep them in place ... barring an insane wind. Notice his are secure at the top so any minor roof lift by wind will keep it in place.

  • @rolfsinkgraven
    @rolfsinkgraven2 жыл бұрын

    Primer on the bottom of the old wooden Column would help

  • @joshuamills2868
    @joshuamills2868 Жыл бұрын

    Look at Tommy wearing Patagucci😂

  • @DARWINZOO
    @DARWINZOO2 жыл бұрын

    This is identical to my house outside Boston.

  • @sorenhammerholder21
    @sorenhammerholder21 Жыл бұрын

    Was the base anchored to the concrete?

  • @SalvadorSTMZ
    @SalvadorSTMZ2 жыл бұрын

    Came out great. Would adding a plastic liner in between the post and the concrete be a bad idea? Since water makes its way from the concrete up into the post.

  • @danielmarquardt4341

    @danielmarquardt4341

    2 жыл бұрын

    2:39

  • @Farm_fab

    @Farm_fab

    2 жыл бұрын

    The materials they used do not absorb moisture as it is made with the hulls of rice and polymer for adding a bit of strength. There would be little benefit to plastic. This product is called Resysta.

  • @kalijasin

    @kalijasin

    2 жыл бұрын

    Still should of put a two light coats of Rubberseal or Kilz on the bottom of base just to be on the safe side.

  • @Fattony6666

    @Fattony6666

    2 жыл бұрын

    @@kalijasin no

  • @troybush5899

    @troybush5899

    2 жыл бұрын

    @@kalijasin Should HAVE , not should of....

  • @meggopeggo.
    @meggopeggo.2 жыл бұрын

    Is this material at the base okay to support a heavy duty roof?

  • @raymendoza-hr9jv
    @raymendoza-hr9jv10 ай бұрын

    Did you buy the rice hull board by the sheet or by the trim board?

  • @robremlap4071
    @robremlap40719 ай бұрын

    I've got some kind of metal base at the bottom of the only portch columb I have, but the wood around it is starting to rot. I can fix it myself if I knew what all it wil take to replace it

  • @happypeople3952
    @happypeople3952 Жыл бұрын

    Does anyone know if these columns are load bearing ? They are hollow . My house has the exact same columns and structures .

  • @scottdunn6065
    @scottdunn606511 күн бұрын

    i have some somewhat square posts sitting on concrete columns with stone accents that have trim going around them that keep rotting and needing to be replaced every so often , what can i do to prevent that ? i understand that they absorb the moisture from the stone column.

  • @saadzeb8055
    @saadzeb80552 жыл бұрын

    Plz make video om how to repair old normal door. Specially washroom door that has holes..

  • @patkellyd
    @patkellyd Жыл бұрын

    can anyone suggest other material options that rice hull board? It's hard to find. Thanks

  • @werther5952
    @werther59526 ай бұрын

    Should they tapcon that base to the porch? The screws he sunk into it looked like they wouldn't reach the cement porch. Maybe it was just the angle?

  • @phillebeau9464
    @phillebeau94642 жыл бұрын

    Do I need (stair) sub-treads to go under 1inch solid oak stair treads? I removed carpet off the steps, currently there are 2 inch raw construction treads. I will take those off and replace with 1 inch solid oak treads. But I will loose 1 inch rise. I have 3 stringers, left right and middle. Thanks.

  • @Kulpythekulpster

    @Kulpythekulpster

    2 жыл бұрын

    Glue 2 1x together and router. Or use 2x oak or whatever you want again.

  • @ralphietito
    @ralphietito2 жыл бұрын

    I have the exact same problem, but can’t find the same type of lumber. Does anyone know where to find it?

  • @danielgao52
    @danielgao522 жыл бұрын

    👍👍👍👍👍👍👍👍

  • @Cdshakes
    @Cdshakes2 жыл бұрын

    I know for the broadcast TV show there are time constraints. But it's time that you make an online version that shows the full details. I can't believe they spent this much time showing how they leveled it and put those scribe pieces on the bottom but then never showed how to actually cut to the scribe marks

  • @michaell171

    @michaell171

    2 жыл бұрын

    I came to the comments looking for that same explanation. They look too thin for a table saw. Maybe they used a bench sander?

  • @jds604
    @jds6042 жыл бұрын

    Thought this was NS Builders for a second lol

  • @cargogh

    @cargogh

    2 жыл бұрын

    Thought that also, both on thumbnail and for a split second at the door.

  • @MESTER47
    @MESTER472 жыл бұрын

    Why not to change both of bases, for a longer life?

  • @tmurray1972
    @tmurray19722 жыл бұрын

    What did you remove the material with on the scribed pieces?

  • @Farm_fab

    @Farm_fab

    2 жыл бұрын

    They used a jigsaw or a sabresaw.

  • @tmurray1972

    @tmurray1972

    2 жыл бұрын

    @@Farm_fab Thanks, I didn’t see it..lol.

  • @alexknight7191

    @alexknight7191

    2 жыл бұрын

    I had to rewind to see if I somehow missed it, but yeah odd to leave that out.

  • @DIYREN1
    @DIYREN12 жыл бұрын

    I am not an expert on this, but should I worry about the hollow center of the square base? the square base is glued from 2 pieces and supported only on the 4 sides, while the center of the base supports the weight of the column and the porch, am I worrying too much?

  • @jamesross1798

    @jamesross1798

    Жыл бұрын

    The column is round and hollow, so the weight is actually on the edges of the square base, not center. ⭕🔲

  • @pacificwhim
    @pacificwhim2 жыл бұрын

    Darn it, he didn't say "rabbet" or "dado." It's not really a Tom Silva video unless at least one of those words comes up.

  • @jacobtracy7847

    @jacobtracy7847

    2 жыл бұрын

    How about temba.

  • @rupe53

    @rupe53

    2 жыл бұрын

    @@jacobtracy7847 ... Tom is good but Norm would have made several pieces then used his biscuit cutter to glue things up, PLUS, doing several passes with the router blades to make a decorative bead accent for each layer.

  • @JennAngel24
    @JennAngel2427 күн бұрын

    A hole was drilled in the center of the new post base so air could go up into the column to keep it dry. But how is air going to get though if the joints are sealed? I have to fix my front porch corner column and porch because the previous owners didn't clean out the gutter, so the water overflowed onto the porch & column.

  • @Russellviews

    @Russellviews

    10 күн бұрын

    You can put spacers under the base to allow moisture release.

  • @vincejuarez4465
    @vincejuarez44652 жыл бұрын

    Isn't the column still weak and hallow from the center . When tommy took the old one out , alot of bad wood came out ?

  • @Guillotines_For_Globalists

    @Guillotines_For_Globalists

    2 жыл бұрын

    That was the ant nest. It would appear that the center of the columns is hollow.

  • @mr.popularpants253
    @mr.popularpants2532 жыл бұрын

    Does jacking it up not damage the house or loosen any nails or screws?

  • @mae2759

    @mae2759

    2 жыл бұрын

    No, not at all. Very common practice. You're only jacking it up less than an inch.

  • @rupe53

    @rupe53

    2 жыл бұрын

    @@mae2759 ... in most cases it's less than 1/8 inch. At that height you are not pulling nails or screws. You are basically flexing the wood. (no more than what happens with a change of season)

  • @winer9098
    @winer90988 ай бұрын

    How much would y’all charge for this job

  • @MB12116
    @MB121162 жыл бұрын

    Why didn’t you anchor the post into the concrete?

  • @Michael1M6
    @Michael1M62 жыл бұрын

    I’m confused! Was the column hollow or did the ants eat into the column? That nest came down as soon as he cut the post!

  • @tj_gsomething_

    @tj_gsomething_

    2 жыл бұрын

    The ants moved the wood from below, up into the column. Most columns are hollow. Tapered or non-tapered fluted or plain are all hollow. Also when you look at the different materials: polymer stone, fiberglass, PVC and even wood they are all hollow. ... A wood porch column is made by gluing staves together in a circular form and then turning and cutting them on a lathe.

  • @robertbamford8266

    @robertbamford8266

    2 жыл бұрын

    @@tj_gsomething_ So … the concern is whether the carpenter ants continued to eat their way up the post. It looks like the infestation is not still active.

  • @cup_and_cone

    @cup_and_cone

    2 жыл бұрын

    The column is hollow. The nest was likely sitting right on top.

  • @rupe53

    @rupe53

    2 жыл бұрын

    ... basically, the ants stop where the water problem stops. Worst case is they cut the column higher and make a taller base, then match it on the other side.

  • @hilalyendork7371
    @hilalyendork7371 Жыл бұрын

    What’s the board called?

  • @Clark-Mills
    @Clark-Mills2 жыл бұрын

    Maybe spray some insecticide up inside the hollowed out column before reassembling? I think those ants will continue to eat up the column.

  • @MoneyManHolmes

    @MoneyManHolmes

    2 жыл бұрын

    I wonder what the bottom of the column looked like. Too bad the camera cut away and didn’t show it.

  • @Clark-Mills

    @Clark-Mills

    2 жыл бұрын

    @@MoneyManHolmes Seemed bug-hollowed when the nest material fell out, which is what prompted my suggestion. I'd say you saw what I saw... :)

  • @Guardducks
    @Guardducks2 жыл бұрын

    A little kilz primer and your good for a few years.

  • @katmandu8275
    @katmandu82752 жыл бұрын

    where did he put the jack?

  • @todd2456

    @todd2456

    2 жыл бұрын

    Back in the truck when he was done.

  • @jessasdad
    @jessasdad2 жыл бұрын

    “Nice and tight”…Tom Silva

  • @stormb28
    @stormb282 жыл бұрын

    Who would I call to have porch columns installed?

  • @Guillotines_For_Globalists

    @Guillotines_For_Globalists

    2 жыл бұрын

    Ghostbusters

  • @rupe53
    @rupe532 жыл бұрын

    Good chance the base rotted because that bush was overgrown for many years. No bushes on the other side = no moisture and no rot.

  • @paulmitrano3612
    @paulmitrano36122 жыл бұрын

    You've come this far, probably should've inspected and reworked the column too.

  • @Engineer9736

    @Engineer9736

    2 жыл бұрын

    They started out with the inspection on that column right at the beginning of the video

  • @paulmitrano3612

    @paulmitrano3612

    2 жыл бұрын

    @@Engineer9736 Poking a Leatherman at a column doesn't mean the inside is sound. Look at the carpenter ant nest that came out of there.

  • @Farm_fab

    @Farm_fab

    2 жыл бұрын

    @@paulmitrano3612 the rot starts from the outside inward, and the rot made it easy for the ants to cause damage.

  • @BC-ux9iw
    @BC-ux9iw2 жыл бұрын

    I have a question for this old house…… I have a120 year old house. During a remodel they reframed the stairs. Now they lean. How do I fix that? I can send pics.

  • @tj_gsomething_

    @tj_gsomething_

    2 жыл бұрын

    Is the foundation sinking/settling? If you place a ball on the floor, does it roll in the same direction? Maybe the house needs to be leveled?

  • @gpslightlock1422

    @gpslightlock1422

    2 жыл бұрын

    You tell the guy you paid for the remodel to come back and fix it.

  • @marist89
    @marist892 жыл бұрын

    I know it's a budget difference, but wouldn't a better long-term solution be replacing the columns with fiberglass columns?

  • @tj_gsomething_

    @tj_gsomething_

    2 жыл бұрын

    Fiberglass will definitely last longer than wood. So yes it's gotta be a budget difference. They didn't even recommend doing the other side. You know that other side will need updating soon!

  • @Farm_fab

    @Farm_fab

    2 жыл бұрын

    @@tj_gsomething_ they may have done this this way so the homeowner could do this at some point in the future, and teach him some responsibility.

  • @degenwow
    @degenwow2 жыл бұрын

    The Show should have brought pocket-less trousers for the home-owner.

  • @geraldtrembley2425
    @geraldtrembley24252 жыл бұрын

    if Sam is looking for his hands,there in his pockets.

  • @espnmk
    @espnmk2 жыл бұрын

    hope that homeowner didn't stretch out those kaki pant pockets too much.

  • @christophergaither2032
    @christophergaither203210 ай бұрын

    You never place wood directly on a concrete porch. The wood will act like a sponge with any moisture that may be sitting on concrete. Get a specific either metal or reinforced plastic base to separate contact between concrete and wood

  • @Russellviews

    @Russellviews

    10 күн бұрын

    Agreed. I would have done what you said but my porch is wood.

  • @the_realJP_
    @the_realJP_11 ай бұрын

    “Copenter” ants 🐜

  • @geraldtrembley2425
    @geraldtrembley24252 жыл бұрын

    I thought the idea of this show was for the home owner to help Tommy.Hard to do that with your hands in your pockets.

  • @strawberriebabieex3
    @strawberriebabieex32 жыл бұрын

    Does the homeowner ever take his hands out of his pockets?

  • @TheAavelar007
    @TheAavelar0072 жыл бұрын

    If that is MDF it is a bad idea to use it outside..

  • @pistolpete5325

    @pistolpete5325

    2 жыл бұрын

    2:25 pay attention

  • @alfredovasquez1439
    @alfredovasquez14392 жыл бұрын

    I don't think he's going to paint it, his hands in his pockets say it all

  • @wowandflutter

    @wowandflutter

    2 жыл бұрын

    He was playing "pocket pool" while admiring Tom Silva work that column 🎱

  • @etiennelj
    @etiennelj2 жыл бұрын

    Hands in pockets… wow…

  • @scarce911
    @scarce9112 жыл бұрын

    Ours are concrete and about 25" square..I hope they don't rot 🤭

  • @kalijasin
    @kalijasin2 жыл бұрын

    Carpenter ants 🙈

  • @snapjamwoodworks710
    @snapjamwoodworks7102 жыл бұрын

    1.79 million subs and I am the 28th person to watch!!

  • @johnnywood8082

    @johnnywood8082

    2 жыл бұрын

    You want a cookie?

  • @snapjamwoodworks710

    @snapjamwoodworks710

    2 жыл бұрын

    @@johnnywood8082 Lol yes please

  • @fireblaster9961
    @fireblaster99612 жыл бұрын

    Wow he actually used a mdf type material and no damp proof protection

  • @Engineer9736

    @Engineer9736

    2 жыл бұрын

    2:50 First watch the video before barking

  • @Farm_fab

    @Farm_fab

    2 жыл бұрын

    @@Engineer9736 they used a product called Resysta that's made from polymer and rice hulls, and is impervious to moisture.

  • @chrisburns5691

    @chrisburns5691

    2 жыл бұрын

    Mdf lol...

  • @Engineer9736

    @Engineer9736

    2 жыл бұрын

    @@Farm_fab They explained that, yes, you have to say that to Fire Blaster, he didn’t hear it

  • @stevendavanna
    @stevendavanna2 жыл бұрын

    First comment

Келесі