Thank you for this video. It's been invaluable in pointing me in the right direction with replacing mine 👍

At last a video fully explaining and demonstrating the use of a bearing removal/installing kit.. Now I am confident on how to do my Peugeot 308..Thak you!

@TheDutchGarage

11 ай бұрын

No problem, glad to help!

Great video. I am changing a wheel bearing on my Citroën c4 with your video as guide. I have the exakt same problem as you, the split bearing and the lock ring that just don't want to come out.

@TheDutchGarage

6 жыл бұрын

Feel your pain my gabber... Show it who is boss!!!

Thanks for uploading this video. Exactly what I was looking for.

@TheDutchGarage

5 жыл бұрын

No problem, glad that i could help.

Very good video, thank you for your time and effort

@TheDutchGarage

2 жыл бұрын

Thank you, and no problem.

I have replaced 3 wheel bearings on this vehicle and they keep failing after a week or so! I dont know what is causing it, i have changed the driveshaft im thinking maybe wrong cv joint would this cause the bearing to fail? also do u not tighten the bearing with wheel on ground? or is there no need on this car. thank you

I've just bought a CXP 2006. It has problems with rear axle suspension, I suppose. I hear sometimes cracking noises from the rear (I can't decide the correct side), I think it's the drivers side (left side in my country). I'm considering to replace the suspension on rear axle - both sides - and also the right side brake disk is rusty on the outer side. What could be the cause and can I do the replacement - both suspension and brakes - on my own or do you recommend to go to the workshop?

@TheDutchGarage

6 жыл бұрын

+skru2b . the rear axle has torsion bars. Those are a real pain in the arse to replace! In your case i think the bearings in the axle are bad. If you are going to replace them. You can beter buy a refurb rear axle. But if you want to do it, remove the whole axle from the car! Good luck!

Very nice and thorough video!

@TheDutchGarage

7 жыл бұрын

Thanks for the nice comment!

thanks sir. nice instruktions. helped me do the job faster.

@TheDutchGarage

7 жыл бұрын

Glad i could help, good luck with the job!

Good work, very instructive video.

@TheDutchGarage

5 жыл бұрын

thank you!.

Very good video. I am about to change a front wheel bearing on a Citroen C3 Desire 2004. Is this the same for this car?

@TheDutchGarage

4 жыл бұрын

I don't know if it is the same bearing but it looks like the procedure is the same. Just be sure to check the torque specs.

detailed and informative, thank you!

@TheDutchGarage

7 жыл бұрын

No problem!

very useful and many thanks for sharing video

@TheDutchGarage

6 жыл бұрын

Glad it helpt you out. Thanks for the comment.

Thank you. Really informative video.

@TheDutchGarage

6 жыл бұрын

No problem and thank you!

Does the bearing have to be magnetic

Nice job.

@TheDutchGarage

7 жыл бұрын

Thanks!

Great video. Thanks. I'd only add the air wrench is dubious on the drop link without a spanner on the ball joint side too. The new looking boot splits at 14:07 but these links are now very cheap for a pair ;-)

@TheDutchGarage

4 жыл бұрын

Thank you, yes your better of supporting the ting you are completely right there. Those things are fragile

Very informative

@TheDutchGarage

7 жыл бұрын

Thanks Kevin!

very nice job! ur a good teacher! do u know if it same in citroen c5 2009?

@TheDutchGarage

7 жыл бұрын

Thanks! No the suspension is totally different. Off course the basic principle is the same. But the bearing is punched out and in from the front side.

GREAT VIDEO,THANKS

@TheDutchGarage

5 жыл бұрын

No problem, thanks for watching.

very good video

@TheDutchGarage

7 жыл бұрын

Thank you! Thanks for watching.

Good video

@TheDutchGarage

3 жыл бұрын

Thank you.

Nice job

@TheDutchGarage

6 жыл бұрын

Thank you!

Is it the same type of setup on a Peugeot 307?

@TheDutchGarage

6 жыл бұрын

Hallo, the knuckle design is different (lower ballpoint is the biggest difference)but the proses is almost the same. They use the same bearing. But be sure to get a bearing with a ABS ring if you have ABS. and also be sure that the abs ring is pointing to the back were the sensor is located.

why you didn't take mcperson out?

@TheDutchGarage

2 жыл бұрын

I could have done that but it isn't necessary.

For the ABS?

@TheDutchGarage

3 жыл бұрын

No, these have a ABS ring on the driveshaft.

What size is the nut on the driveshaft please

@TheDutchGarage

5 жыл бұрын

Hi, 34 i believe it is.

@phillipbestwick22

5 жыл бұрын

Mine is bigger thought it was 36mm but even that's to small guessing a 38mm

Do you have a part number for your tools please ?

@TheDutchGarage

6 жыл бұрын

Hallo, i used the midlock 2520 slide hammer. I dont know the brand or number of the bearing puller. But here is a link to a just like it. rover.ebay.com/rover/0/0/0?mpre=https%3A%2F%2Fwww.ebay.co.uk%2Fulk%2Fitm%2F202091066761 I hope it helps you out.

@didar389

6 жыл бұрын

The Dutch Garage that is great thanks for your help and thanks for the great video 👍

@TheDutchGarage

6 жыл бұрын

No problem, thanks for watching!

Is it the same as a 2005

@TheDutchGarage

7 жыл бұрын

Yes sir, same car. Happy wrenching!