I did it with a regular jack that comes with car kind of a hard time trying to hammer disk out. I took the 4 screws from the wheel bearing off and hammered the wheel bearing off the disk later. Thanks for posting this video Omar and take care

I just worked on 2015 Nissan Altima doing the same thing as your video. Your video helped me a great deal in replacing the rear bearing assembly. Thank you for such a great and detailed video. Much appreciated...👍👍👍

@omarlopez-eb2nd

4 жыл бұрын

Hi Wildkid 21. Glad to hear this video showed you the steps. Thanks for watching and God Bless You. Like subscribe and share thankyou

Great video gonna go do this job in the morning. Thanks bro

Great info. Thanks for making a video on this replacement.

Thank you brotha. Thought I had to take apart drum brakes.

I did a 2012 Maxima today and it was the easiest wheel bearing I have done in all my years of working on cars. Took 50 minutes even with gathering tools. Used Timken. Learned about the smaller orientation on top from your video. Had to hand thread all 4 bolts and then rubber mallet into place. I sanded opening of rust. 65 Ft lbs on bearing bolts.

@omarlopez-eb2nd

4 жыл бұрын

Hi Sir Sweetness. Glad too hear this video is capable of helping others, it is a pain in the rear too hand thread bolts 😆. God Bless like and subscribe. Good luck

Dude, I can't thank you enough for taking the time to post this video, gonna have to do both back ones. Thanks again.

@omarlopez-eb2nd

4 жыл бұрын

Hi Tony Boff, glad you enjoyed my video. Good too hear it helped you. Thanks for watching like subscribe. God bless. P.s use a 2x4 to loosen the rotor, don't hit directly with hammer.

This video will help also with the 2014 Nissan Altima. Thanks to your video I knew what to expect and it took me about 30 minutes. Thank you for sharing.

@omarlopez-eb2nd

5 жыл бұрын

Great too hear it helps bro. Thank you

Thanks Omar! Very helpful and saved me time! Really appreciate your thorough explanation!

@omarlopez-eb2nd

4 жыл бұрын

Glad to read, that it helped you JP Freeman. I try too explaine exactly what too do. Thank you for watching..

Thank you!

Thanks for the video bro, definitely helped me out today

@omarlopez-eb2nd

4 жыл бұрын

Thanks for watching bro. Subscribe,, good luck

You should release the drum brake, it makes removing disc easier

Great video, thanks 👍🏼

Never hit rotor directly with hammer. Use a block of wood instead. Unless you are replacing rotor.

@omarlopez-eb2nd

4 жыл бұрын

Yes sir sweetness, i did have a buddy come over and help me remove a rotor on a separate car, he said the same thing. Thank you for your comment god bless

I feel like i just got off a roller coaster

Молодец. Очень хорошее видео. Спасибо.

@omarlopez-eb2nd

4 жыл бұрын

Hi jack Mil. Thanks for watching this video. Also i can't read what you commented. Hope you can translate please and hope this video helped you. Like subscribe

Thanks bro

@omarlopez-eb2nd

4 жыл бұрын

Thank you for watching like and subscribe goodluck.

Great video How do you change the dust shield ? Mine has completely crumbled from rust. Do you think that it's important to replace it? Thank you

@omarlopez-eb2nd

Жыл бұрын

Well sorry for the late super late response.. It is required to keep dust away from your break lines or such behind it also heat can melt your lines so im pretty sure it's useful to have the shield there.

Is it the same process for the front bearing? Same make, model and year

@omarlopez-eb2nd

4 жыл бұрын

Hi Malachy jackson. Glad you enjoyed my video. It might be a bit tuffer for the front bearings, due to it being a front wheel drive. But not at all hard too DIY. Just make sure you dont stripp the rear bolts. Like subscribe God Bless you good luck.

@malachyjackson1562

4 жыл бұрын

Appreciate it and will do 🤟🏽

Any recommendations for stuck rear wheel bearing? Have the same model Altima?

@omarlopez-eb2nd

4 жыл бұрын

If its super stuckjust keep putting wd 40 keep soaking it. Then hit it with dead bold hammer untill it loosesn up. Carefull not too strip the bolts

@omarlopez-eb2nd

4 жыл бұрын

Also it can help to pry it off with a thin prybar and a hammer

Nice video dud, i hace to replace in my nissan, but i dont know how, can see which is the bad one, just the noice is anoing,

@omarlopez-eb2nd

4 жыл бұрын

What i do to find out wich one it is. I have someone drive the car and i hop from passenger seat too rear seats. Usually its the rear ones first that start making the noise. Good luck brother thanks for watching. Like subscribe

@cmontygman

4 жыл бұрын

@@omarlopez-eb2nd Theres another video I found that makes it easier to isolate the noise once you have a general idea of which bearings (front/back) but what you do is jack up the car,rotate the tire while you have your hand on the strut, if you feel any vibrations from the strut on your hand while its moving that bearing is bad.

@omarlopez-eb2nd

4 жыл бұрын

@@cmontygman love it bro. Good idea i will try it when next car rides in brother God bless you

What's name of brand ? After one year still working properly ? Do you recommend the brand ?

@omarlopez-eb2nd

Жыл бұрын

It all depends on your budget. I usually use the mid ones. It stops my cars as if it were the expensive ones. Duralast brother

Will this work for a 2013?

@omarlopez-eb2nd

4 жыл бұрын

Hi Buck Town. Hope you enjoyed my video. It should be the same if not its not that different. I believe 12 13 to 16 it's the same. God bless you and good luck . don't forget too like and subscribe.

Is the front the same?

@omarlopez-eb2nd

11 ай бұрын

Its a slight diferent rotor. But it's the same process, if that's what you qre referring too. The bearring should be a bit more challenging, being that you will need too remove the cv axle nut amd push in the cv axel with a rubber mallet, that way you dont hurt/strip the grooves on the axle. Good luck let me know your outcome.

My rear rotors are stuck on... any suggestions?

@omarlopez-eb2nd

3 жыл бұрын

Hello and yes use a little WD 40 and use a wood 2x4 and smack it with a dead bold hammer. Leave a lug nut on loosely that way when it loosens up it dosent fall on your toes

@TheFlyingZulu

3 жыл бұрын

@@omarlopez-eb2nd Thanks! I got the rotor to come off... So yep I just had to hit it harder and a few more times. haha.