No video
How to Repair a Water Pressure Regulator | Zurn Wilkins 600XL
Learn how to repair or rebuild a Zurn Wilkins 600XL water pressure regulator. This is a simple repair for the DIYer.
@HacksbyDad
Thank you for supporting my channel through Patreon... / hacksbydad
Disclaimer:
This video description contains affiliate links. That means if you make a purchase or sign up for a service after clicking one of my links I may receive a commission, at no extra cost to you. As an Amazon Associate, I earn from qualifying purchases.
Thank you for supporting my channel!
The Zurn RK34-600XL repair kit is available at Amazon... amzn.to/3qO8WtP
Also, please check out my Amazon Storefront... www.amazon.com...
This video is for entertainment purposes only. Rely on the information in this video at your own risk.
Пікірлер: 47
Thank you SO much. This worked PERFECTLY for me. My regulator had been replaced by a plumber about 10 years ago and failed last month. The inside was a rusted mess, although the only thing actually 'broken' was the small rubber O ring. I ordered the repair kit from Amazon for around $60, and with a couple of hours work (the two plugs at the bottom were frozen solid and needed a lot of work to remove which added an hour) I saved a $400 (or more) plumber's visit to replace the valve. The only difference between my 1" device and the one in the video was that the new stem was not a threaded stud at the top , but instead was a tapped hole so the diaphragm was attached with a supplied bolt instead of the nut in the video. It all went together exactly as described otherwise, and when it was done I turned on the water and no leaks and set the pressure for for 65 psi using a meter I had. Excellent no nonsense video. Grateful for your time in posting this.
@HacksbyDad
3 жыл бұрын
Thanks for the feedback! Glad to hear that the video was helpful and you were able to rebuild your water pressure regulator. 😎
Outstanding how efficient you are in your video at describing and showing, kudos!!
@HacksbyDad
14 күн бұрын
Thanks… much appreciated! 👍😎
EXCELLENT ! Your great video saved me $400 !!!
@HacksbyDad
2 жыл бұрын
Glad to hear it! Thanks for the feedback... I really appreciate it. 😎
Thanks for the video really helped my confidence. Got it fully done in about an hour and no more high pitched noise when the water flows. Thanks!!!
So that's why the bell housing is shaped like that--because there's a big compression spring inside. I always wanted to know that. Great video. Thank you.
@HacksbyDad
2 жыл бұрын
You're welcome! Glad to hear that you found the video helpful. Thanks for the comment. 😎
What a legend, this video is perfect. Thank you!
@HacksbyDad
Жыл бұрын
👍
Thank you! Helped a lot! Saved $200 as the 1" Zurn valve is now $264 at HD.
@HacksbyDad
2 ай бұрын
Glad to hear it! 👍😎
What a great video. Very informative and straight to the point. Thank you so much.
Thank you - mine is a different model but this gave me confidence that I can tackle the job! Your style is direct and no-nonsense, keep it that way!
@HacksbyDad
3 жыл бұрын
Thanks! I really appreciate the feedback! Good luck with your rebuild. 😎
Worked great. Thanks for giving me the confidence to try the repair myself. I will confess that I have checked it for leaks a few times since I did the repair last evening, but I am a little paranoid about water leaks. Nice to have it working again.
@HacksbyDad
2 жыл бұрын
You’re welcome! Thanks for sharing. 😎
Thanks you so much for this video. It was very helpful in replacing the guts of my Wilkins 600 regulator with the the RK34-600xl kit.
@HacksbyDad
8 ай бұрын
You’re welcome! I’m glad to hear that you found the video helpful. 😎
Direct and to the point! Thank you
@HacksbyDad
11 ай бұрын
👍😎
Great job !!
@HacksbyDad
Жыл бұрын
Thanks! Much appreciated! 😎
Great video. Straight to the point.
@HacksbyDad
Жыл бұрын
Thanks! Much appreciated!
Thank you, sir. Great instructions…works like a charm. I saved $$ by doing this!
@HacksbyDad
Жыл бұрын
You’re welcome! 😎
The instructions were terrible and I had a leak! Your video was perfect as I had the friction ring installed on the wrong side. Thanks!
@HacksbyDad
Жыл бұрын
You’re welcome and thank you for the feedback. Much appreciated! 😎
@RogerPack
Жыл бұрын
Diaphragm is another name for it?
Excellent Video Thank You!
@HacksbyDad
4 ай бұрын
You’re welcome and thank you! 😎
Wow I’m not sure what yoU do in your everyday job BUTT yoU should consider presenting yoU aRe brilliant well done SIR
@HacksbyDad
8 ай бұрын
Thanks! Much appreciated! 😎
Good job.
@HacksbyDad
2 жыл бұрын
Thanks. I appreciate the feedback. 😎
Thank you.
@HacksbyDad
2 жыл бұрын
You’re welcome. 😎
Thank you so much! I was just replacing faucet cartridges and a friend said it might be the regulator. Got the same one you have ;) and sure enough, I have 118psi :( I'll get the kit and give it a go! Can you help me better understand what "not over tighten the plunger" means? Also, when I reassemble the plugs should I add teflon tape or anything like that? I subscribed to your channel because of all the help in this video! Thank you again!
@HacksbyDad
Жыл бұрын
Thanks! I posted the video 2 years ago and needed to watch it to jog my memory. LOL! Just snugly tighten the plunger… don’t use much muscle. Use the gaskets in the kit and Teflon tape won’t be needed. Hope this helps. 😎
This is very good to know about it's, but do they sales those repairs kits for us and where to buy it from? Thank you so much for showing us how to repairs this
@HacksbyDad
2 жыл бұрын
Thanks for the question. Yes, the repair kits are for sale to the general public at many plumbing supply stores. Click the “ Where to Buy” button on the Zurn Wilkins website to find a dealer near you. I also placed an Amazon link for the 3/4” pressure reducing valve in the video description. Confirm if yours is 1/2, 3/4, or 1”. Good luck with the repair! 😎
How big are those large pipe wrenches?
Does it mean mine is bad if the water is surging ?? It’s not a constant flow
But it only happens when I use the washing machine ?
@HacksbyDad
2 жыл бұрын
Surging? I’m not a plumber but maybe it’s water hammer. Might be that the water inlet valve in the washing machine is faulty. You can try removing the hoses on the machine side and running the hot and cold water into the laundry sink. If no surging, then it is probably something to do with the washing machine. 😎