Devcon Repair Kit (White/Almond): amzn.to/2VDDdN5

@milushardwick2404

2 жыл бұрын

Do I need to let the epoxy cure 1st, before I sand it?

You inspired me to remove my shower doors and do curtains. Thank you. I followed your steps to the T and i also got great results. ❤️

I just removed the metal frame from my tub and just knew KZread would have a video on how to cover the screw holes. Thank you for posting this “how to” video! How did anyone fix anything ever before KZread??

@EverydayHomeRepairs

4 жыл бұрын

Hahaha, no doubt. A am an amateur creator and a professional user of KZread for How To Videos 👍 Best of luck on the project!

@JenJen0582

16 күн бұрын

I just removed the glass doors a few days ago and I found this video how to patch the holes. How did yours come out?

Pretty good. Remove first blue tape when wet. Replace when dry and ready to sand. No cutting and dried glue on tape that way. You can also use a small plastic blade, even an old piece of stiff plastic, as a mini trowel to push some puddy in.

Again, answered the mystery question about what to do with the holes in the fiberglass. Thanks so much!!

Thank you for such a thorough video! Like you, we removed the doors from our shower and are replacing them with a curtain rod and curtain/liner. This will definitely help when we need to fill in those screw holes!

Thanks for the video! Just discovered a tiny hole in the corner of my tub from where I think I knocked too hard with the scrub brush. Ordered the kit you suggested and I'll check back when it gets here and rewatch to make sure I do it right.

Thank you for this mini series on how to change the glass door to shower rod, I’m going to be doing this project with my dad in a month or so once I have everything I need so thank you so much! 😊

@EverydayHomeRepairs

3 жыл бұрын

No problem, glad you found all the videos and best of luck on the project 👍

@angelmonarrez3734

10 ай бұрын

Question is do you remove the plastic piece when dry or while still wet

Thank you! I’m going to remove mine this weekend and Will for sure refer back to this for help on repairing the holes.

@EverydayHomeRepairs

3 жыл бұрын

Nice, best of luck on the project. As others have stated when you mix the epoxy it will start to setup fast so be prepared since you will be doing multiple holes.

Thanks for the video, I ordered this product many months ago as I saw it being used in another video. I'm just getting around to using it and found your video. I just applied it using your technique and am waiting for it to dry so I can sand. I will update on the progress.

@EverydayHomeRepairs

3 жыл бұрын

How did the project turn out?

Concise and well explained. A rarity on KZread. Thank you

@EverydayHomeRepairs

4 жыл бұрын

We try our best to keep the video focused on the specific goal. Best of luck on your project!

Thanks for posting both videos re shower door removal & repair. Planning on doing our soon. BTW: People who wonder why you'd remove shower doors & replace w/shower curtain have never had to spend an entire weekend trying to remove soap scum from doors and rails.

@EverydayHomeRepairs

3 жыл бұрын

No doubt, I have another one to remove from a shower in a condo I just purchased. Super grimy 🤢

Great demo! I watched it 2x-3x to make sure I had all the steps in mind before I started my project. I wondered how long you waited before sanding?

Thanks for the video. Clear explanation. I have a white surround so I just purchased a cheap, white two part expoxy. It came out nice!

@EverydayHomeRepairs

3 жыл бұрын

Great, thanks for letting us know about an alternative which also worked well.

Thanks - getting ready to start the exact same project tomorrow!

@EverydayHomeRepairs

4 жыл бұрын

Great, best of luck on the project. I was just discussing with someone else and they were surprised how fast it starts to harden so just a heads up that you won't have much more than 5 mins or so to work the material into the holes. The tape and plastic bag will help with sanding.

Hey, nice job. That turned out pretty good. I have 4 small holes like the ones in your video that I need to repair. Will try this kit, thanks for posting 👍

This is super helpful! Thank you for mentioning the air bubbles!!

The plastic to smooth and remove the bubbles is brilliant. Do you leave the plastic in place until it is completely dry?

Wow looks great. We are definitely gonna remove our glass doors. So hard to clean and bathe the kids with it

Nice job. With video edit and conciseness. And nice patching work. Thank you

@EverydayHomeRepairs

3 жыл бұрын

You're welcome!

Great tutorial, thank you! I couldn’t get the almond color out of the bag so I just used it as is. Oh well, hopefully it won’t be too noticeable.

@EverydayHomeRepairs

3 жыл бұрын

Hope your project worked out 👍

Wow this looks like a lot of work.

Thank you. Thanks to this video, my hole repair didn't look like other ones on KZread. It is fairly flat and smooth. I did find out the hard way that the almond color of a fiberglass tub does sand off. I wish I had taped more strictly. My repair ended up with small bubbles in it, and needs polishing (after using wet 600 grit).

@EverydayHomeRepairs

4 жыл бұрын

Yeah, I think some people have used automotive rubbing compound to try and bring back the shine. Overall mine isn't perfect either but overall it actually worked better than I had originally expected.

There's no way he didn't scratch that surround, with all that hand sanding . PRO tip: Use a dremil tool and you get all the control you need to sand only the raised area saving the surround from DIY hack job sanding marks.

Great Video !!!! I am off work due to the virus , and have been doing s few projects at home , I have 2 cracks that I will be repairing while I'm off work , Thank You !!!!!

@EverydayHomeRepairs

4 жыл бұрын

Hey Barry, way to put the time to good use. Good luck on the project!

Did you see those sanding skills! Guy was moving at about 100 mph lol ;)

@EverydayHomeRepairs

3 жыл бұрын

Hahaha, I wish the job actually moved at that speed.

Great video, I watched you’re shower door removal video first, also very helpful. I’m a 69 y/o lady live alone and I think I can do this.

Thank you for this video! 🙏🏻

Go Illini! Thanks for your help

Thank you very much gor this video. God Bless you for being so helpful.

So helpful! Thanks.

@EverydayHomeRepairs

4 жыл бұрын

Happy to help Margarite!

I pre fillled screw holes with caulking,let dry few days, then used the kit ,I applied the holes with a hard foam eye shadow foam brush,it worked great,covered with plastic waiting to dry,,,,I feel for just screw holes caulking would be fine,flatten -scrape with a plastic putty knife,let dry ,then artistically paint over with gloss paint,had I known I would not have ordered the kit.The shower water will never hit this area anyway because the shower curtains prevent it.....

Helpful. You made my day. Thanks.

@EverydayHomeRepairs

Жыл бұрын

You bet!

Thanks for the great tips,I will surprise my sister and remove heel old shower rail.

Dope. Ima try it out.

@EverydayHomeRepairs

4 жыл бұрын

I was honestly surprised how good this product worked. Best of luck!

Wow good work

Thanks for this. Very clear and well presented. Will be trying the glass panel removal myself soon, so this is very helpful. My only question is-- where can I get the product that enables me to do the sanding so fast? 😉

Thanks dad 👍🏻

Thanks!

The bag idea was genius. I used this kit today. Didn't come out as nice as your's did but I'm happy with the result nonetheless.

@EverydayHomeRepairs

4 жыл бұрын

Hey Vic, yeah the bag really helped to smooth things out and made the sanding process much easier. Glad you had good luck with the kit as well. Cheers!

@jftoad

3 жыл бұрын

How long did you leave the bag over the epoxy?

@scvic2006

3 жыл бұрын

@@jftoad I definitely don't recall exactly but I think the kit stated drying time for the product. I used that as a gauge.

Great demo. I kind of think that the tape might not have been the way to go since it feathers so nicely. Tape leaves an edge. But I haven't done this so no pro here!

Your shower door removal video and this one are really great and make me feel confident in doing my project, so thank you! However, the tub I'm going to be working on is yellow, and I can't simply replace the whole surround at this point. Do you know of a good product or have an idea for getting a close-match color for the epoxy?

@EverydayHomeRepairs

4 жыл бұрын

Hmmm, you could get dye to add to the epoxy but I imagine it will be pretty tough to match the exact color. The Epoxy sets up pretty fast so you would have to be pretty skilled at getting the right mix prior to applying. Best of luck on the project!

This is a project I will be tackling soon. Thank you. Could an electric sander be used?

@EverydayHomeRepairs

3 жыл бұрын

Hey Tracie, I would probably not use an orbital sander for this job. If you aren't carful and start to sand the surround outside the actual patch then you could lose some of the glossy finish.. With that said you could use some automotive rubbing compound to bring back the finish if needed. Best of luck!

Thank you for sharing information I hate this glass shower enclosure, always feel unsafe to slip and fall through the glass. So great information how to remove when home searching places.

Seems it might work best to fill the holes, scrape off as much excess as you can, then put the tape up to protect against scratching up the rest of the fiberglass. That way you don’t have to sand as much. Right?

@misselanys1219

Жыл бұрын

I would have removed the painters tape as soon as i filled the holes and smoothed down with the plastic bag squares while the epoxy was still wet then let it dry then put fresh painters tape down again and started sanding. This way you are protecting the surrounding fiberglass from scratching and not having to struggle with trying to peel off painters tape essentially plastered to the surrounding wall. Using different grit sandpaper is the way to go . I do drywall hole fills and have it down to a science using that same grit change technique. Now I will use the tape trick too! Great video!!!!

Does this work on a fiberglass acrylic mix? My bathtub has a crack but its a mix. Wasn't sure what would work. Thanks

Suggestion for next time you fill holes: put the toothpick in & break/cut it off so it fills the hole better and gives the epoxy something to go against & use a smaller brush (maybe similar to a nail polish brush) to put it on in thinner coats to see if that helps it apply more evenly to avoid having to do as much sanding. I liked the plastic bag technique for flattening. I saw another video where the patch job looked horrible because the epoxy dripped all over, but this ended up looking good.

@EverydayHomeRepairs

4 жыл бұрын

Thanks for the tips. Think I might have another opportunity coming up on a small condo we are flipping. I will get the toothpicks ready 😁

Are you able to paint tubs if they are scratched? What would u use?

Thank you so much. You did a great job. I only hope I can do as well. We are removing our shower doors for the same reason. I have a new grandson living with me and it’s impossible to bathe him with those doors there. Can’t wait to try this.

How long did it take you to sand and even up each hole?

Great videos! How many screw holes will one kit be able to fill? Did you tape off and fill them all, in all 6 locations, then go back to do the sanding after it dried?

@EverydayHomeRepairs

4 жыл бұрын

Hi Catherine, 1 kit would probably do all 6 depending on the size and any cracks/damage around the hole. I bought 2 just in case as I didn't want to be half way through the project and have to order another kit from amazon. I did the left 3 holes and then the right 3 holes on 2 separate days but that was also because I was trying to document and take video. Best of luck and let me know if you have any other questions.

Good job and go Illinois!

Did you fill the holes all at the same time? The epoxy didn’t dry before you fill all of them?

There's also little plugs you can buy to insert into the holes for a quicker fix.

@EverydayHomeRepairs

3 жыл бұрын

Thanks for the feedback Cindy

@pennyvandevender9031

2 жыл бұрын

What are they called? Where did you find them?

Doesn't all that sanding scratch the fiberglass insert? Also, do you have any videos painting a fiberglass insert white (from almond)?

Do you have a video on installing hand rails for handy cap people in a fiberglass tub like that?

@EverydayHomeRepairs

3 жыл бұрын

Hey Tim, unfortunately I do not have that video at this time. It’s added to the list!

Never used epoxy before. Did you leave the pieces of plastic over for a certain period of time? I was afraid it would stick if I waited and half the epoxy pulled off on the plastic. Then the rest of the epoxy in the container was hardening. I will probably have to buy another kit also do a second coat because what was left in the holes sunk in a little and now it’s not flush with the wall

Thanks, I have a small chip in my tub.

@EverydayHomeRepairs

3 жыл бұрын

Hey Karen, best of luck with the repair 👍

Did you wait a full 24 for it to cure before you started sanding or the 20 minute set time?

Can you use this on cracks in porcelain tubs

I just bought a home that has an old track on the tub. Guess what my first project is going to be! 😁

What is the drying time for the epoxy before sanding

How do you keep the water from coming out the bottom of shower curtain?

When did you remove the baggies after smoothing…did you let it set or right away?

Great video. I don’t have holes like yours but I have a hairline crack (where I can run my fingernail thru it) about an inch wide, would this work? I’m not sure it’s actually leaking thru but better safe than sorry later on.

Thank you for the video. I was noticing the paint color. I like it. Do you know what color it is?

@EverydayHomeRepairs

3 жыл бұрын

No Problem and the paint color is called Repose Gray from Sherwin Williams. Best of luck on your projects. 👍

Thanks for the video! Can you also use spackle to cover the holes if the holes are drilled into the tile? Not concerned about the look for the time being, just wanted to know if that was effective enough instead of buying the repair kit.

@EverydayHomeRepairs

4 жыл бұрын

Hi Michael, I don't think spackle would be ideal for the wet environment but I have heard of people using automotive body filler to fill holes in ceramic tile. If you search the topic on youtube you will find a couple examples. Best of luck!

Time information would have been helpful. How long did you wait before pulling off the tape?

Thanks so much for the info! Our doors were screwed into tile. Will that work to repair holes in tile?

@EverydayHomeRepairs

Жыл бұрын

You need to order yourself one 😉 everyday-home-repairs.creator-spring.com/listing/buy-trucker-hat

Has anyone used this epoxy kit to fix a tub blister on the surface?

Also, this is my first attempt at this type of repair and the instructions are pretty sparse... did you wait the 20 min set time or 24 hour cure time before sanding?

@EverydayHomeRepairs

4 жыл бұрын

Hey Toni, I waited 3-4 hours just to make sure it was dry prior to sanding.

Great video! I purchased two packs and trying to fill 6 - #8 screw holes in a tub surround from a glass shower door. My problem is the epoxy flows out of the screw holes leaving a dimple when it sets up. Any suggestions? I followed your advice almost exactly.

@EverydayHomeRepairs

4 жыл бұрын

Hey Jim, I was also afraid of contraction so I left the epoxy a little higher to allow for some pull back into the hole and still have material for a flush finish after sanding.

@maxkovalov4446

4 жыл бұрын

You can spray expanding foam into the crack before filling it with epoxy.

Does this leave a dull finish or a shiny finish?

Great video but if the hole is any larger than the one you are showing (which is quite tiny) it ain't that easy. I had 6 holes (removed glass door) each about 1/2" diameter from Molly bolts. Too small for that cloth they included and way too large just to cover. I first filled the holes with "GreatStuff" expanding foam to about 1/64" inch below the hole but it was still virtually impossible on all but 1 to get the patch to fully fill the hole. The epoxy is just way too runny. Even tried a second package which was able to level 2 more holes but no luck with the rest. I waited a bit longer on the second coat for it to thicken a bit but that didn't help. Bottom line: For very small screw sized holes it's probably great. Anything bigger, find a different type of epoxy that doesn't run so much. Also, the sanding scratches the finish of the area around the hole. NO WAY to avoid that because the tape eventually has to be removed to blend the epoxy to the enclosure.

I'm prepped and ready to start this same repair today with the same kit. Had not thought of taping off holes or using baggie to flatten. Will do both - do you remove the plastic while still wet or when epoxy is dry? Any issues with the plastic sticking? Great video, thanks!

@EverydayHomeRepairs

4 жыл бұрын

Hey Toni, nope keep it on till dry. You will have no issue with the plastic sticking and really helps get the bubbles out and flatten the epoxy. Best of luck!

Great video Scott. What was your rule of thumb for deciding when to switch your sandpaper to another grit level (to 320, then 600)? Thanks!

@EverydayHomeRepairs

3 жыл бұрын

Hey Khalid, you will only use the higher grit once you have most of the excess material removed. Keep the tape on for as much of the sanding as possible or you will dull the finish of the surrounding area. If this happens I think you can get some automotive rubbing compound to get the shine back as the final step. Best of luck 👍

Your tub looks white to me.. how did you determine it's almond? Ours is pretty old so it's definitely discolored to a slightly off white. So I'm not sure which one to go with.

Do you think this kit would work well for a similarly sized hole in the basin of a tub??

@EverydayHomeRepairs

4 жыл бұрын

Yep, should work great.

Great video! Just curious - why not just fill with silicone caulk? Would that not be just as good?

@EverydayHomeRepairs

4 жыл бұрын

Hey Isaak, I think the caulk would be more of a quick fix but to match color a little better and have a more durable patch I would recommend the Devon kit.

@taylorpresley9887

3 жыл бұрын

@@EverydayHomeRepairs I wish I had just used caulking, this product is crap! Thanks for your suggestion.

@jcm5724

8 ай бұрын

I have to agree with you that the Devcon was very disappointing as I followed Scott's mixing instructions & application but the mixture never cured, even weeks later it remained tacky. I'll now scrape it all off & go with either caulk or one of the many 'j-b weld' options. @@taylorpresley9887

How long does it take to dry?

Mahalo & AWESOME video!

do you have any recommendations on covering holes with ceramic tiles?

@Oneklickmedia

Жыл бұрын

I would just replace the tile or just use grout in a small tube.

At what point did you remove the plastic ziploc bag from the epoxy? Did you wait awhile or take it off right away? Thanks :)

@glenleonard7610

7 ай бұрын

And how long did he let it dry before sanding

Man, this sucker began to set up fast and got super hot. Did I mix it too long or wait too long. Didn't even get 1/2 my holes done before it was too thick to use. Suggestions? I have ordered another kit and I will work faster for the rest of the holes next time. Also, I found that I need to put the plastic on pretty much immediately before moving on to another hole. Any help is appreciated. Great video, btw.

@EverydayHomeRepairs

4 жыл бұрын

Hey Jane, I agree the stuff setups up fast and does pump out a little heat. Like most things the first time is always the toughest since everything is new and you are trying to make decisions in the moment. I think you will be fine on the second batch just pulling from your past experience. If you could get someone else to help they could put the plastic on and start tapping to make sure the finish is smooth and no air bubbles are trapped while you move to the next hole. I have another surround coming up where I need to do the same thing so I will need to dust off my skills as well. Best of luck.

How long did you keep the plastic on after smoothing out the bubbles? I'm assuming pulling back off immediately would disrupt the smoothness but if you wait too long does it not come off?

Did you sand the area prior to applying the epoxy? I just bought the kit and it says to do that, but I didn’t see that step in your video. I didn’t know if it was edited out or maybe simply unnecessary.

@EverydayHomeRepairs

3 жыл бұрын

I did not rough the surface but you are right that is a great first step and will help the Epoxy hold to the surround. Don't forget to clean the surface after sanding to remove all the small trapped particles. Best of luck and remember this stuff sets up pretty fast so you only have about 3-5 mins to get the epoxy where you want it.

Hey I have one question what kind of product did you use to do the shine ?

@EverydayHomeRepairs

4 жыл бұрын

Automotive rubbing compound will be your best bet to bring back the shine.

I have a couple tiny holes in the bottom of my tub that have leaked into the ceiling below. Would this kit work to fill and seal those holes?

@EverydayHomeRepairs

3 жыл бұрын

Yes, this could fix that issue if applied correctly. Best of luck!

Where's the video where you install the curtain rod?

@EverydayHomeRepairs

4 жыл бұрын

Hey Raizza, didn’t put that one together.

holy s*, just like new, entirely indecipherable from the rest. definitely had my doubts with all the videos I've seen on this. If I'm too busy, how much for a service call? I'll buy the materials. Half-joking :)

@EverydayHomeRepairs

3 жыл бұрын

😂 I do agree it is hard to find someone to do a job like this and actually take the time to make it look good. I will let you know when I start the handyman biz 😉

Thank you SO much for this tutorial - but as someone with asthma, friendly warning to PLEASE WEAR A MASK WHEN YOU DO THIS.

I worry about scratching the surface with sandpaper. Create a place for dirt or mold?

@EverydayHomeRepairs

3 жыл бұрын

The tape will be key for not scratching the surrounding surface during sanding.

Hi. The hole in my shower is roughly the size of my big toe (which is what made it). Do you think this kit would work for that?

@EverydayHomeRepairs

4 жыл бұрын

I think it would work. There is a mesh patch which comes with the kit you will need to use on a hole that size. I don't think the finished product will be as nice but it will be water tight and much better than swapping out the surround. Best of luck and let us know how it turned out.

I think I’m just gonna put silicone in that look like a lot of work.

Great DYS clip, bro~! Next time, wear a pair 'o disposable gloves...

I guess I waited too long to use it? I bought this about 6 months ago and just went to use it now - after I broke the seal and poured it into the tray, I started adding the almond color, and no exaggeration, within 5 minutes the tray was burning hot and the epoxy had hardened. Could not fill one hole.

@EverydayHomeRepairs

3 жыл бұрын

That is actually just how fast the stuff sets up. You need everything in place and ready to roll as it doesn't take long to start getting hard.

So how many holes will this kit fix? What is the amount of time to work with it

@EverydayHomeRepairs

3 жыл бұрын

I did 3 to 4 small holes which each kit and you only have about 5 mins or so before it starts setting up.

Wow..... how long did it take to do one hole? Lol Good video. Thank you.

Did you let it dry overnight before sanding, leaving the plastic on overnight as well?

@EverydayHomeRepairs

3 жыл бұрын

I let it dry with the plastic on for 2-3 hours and then started the sanding process. Best of luck with the project!

@pamelaevans5022

3 жыл бұрын

@@EverydayHomeRepairs Do you leave the plastic on or take it off at some point?

@EverydayHomeRepairs

3 жыл бұрын

@@pamelaevans5022 I took it off once I felt it was dry (2-3 hours) you could remove after 1 hour and that might help the speed up the drying process while maintaining the smooth finish.

@pamelaevans5022

3 жыл бұрын

Everyday Home Repairs thank you.

@mrshogwild

3 жыл бұрын

@@pamelaevans5022 great question! I just put the plastic on my holes and didn't know when to take it off. Great series! The heat gun was a life saver!!

Horrible background noise when sanding the epoxy. What was that? A vacuum cleaner?