I really appreciate this content. Unfortunately this is way beyond my understanding and ability. Trying to find someone like you that has the slightest interest in repairing the old stuff let alone making it cost effective leaves most of us with few alternatives. Much appreciated, entertaining too

@robertakerman3570

Жыл бұрын

James Meliti; feel free to review. This is a perfect example/explanation of "basic" electronics. Believe Me when I say "there are very complicated units out there".

tha't's got to be the neatest test bench I've ever seen. a real professional at work.

@EirkenElite

5 жыл бұрын

Lol I have burn holes everywere on my matt lol don't beer and solder

@cat-lw6kq

5 жыл бұрын

I have one of those silicon mats it's safe to drop solder on it, won't burn it.

@joverstreet24

3 жыл бұрын

Nice repair. May be better than ever with all of those new, modern capacitors.

In addition to a variac, my grandfather taught me to use a 200w light bulb wired in series with an outlet. A short in the unit on the bench wont blow fuses or "let the smoke out"... it just lights the bulb.

@fafb9441

3 жыл бұрын

Thanks for the variac suggestion

Instead of variac, You can use a cool life-hack. Around '80 in Poland, transistors were extremly expencive and hard to get, so You can replace main fuse with light bulb socket, and 100w incandescent bulb, power on, and if bulb just flashed and then glowed a bit, there was no short, but if it was still bright glowing, there was a short. And transistors was saved without nearly unoptainable variac.

@fafb9441

3 жыл бұрын

Thanks for this suggestion. The light turns on momentarily bright then dims to about 1/2 intensity.

@fafb9441

3 жыл бұрын

I must add that if the light bulb stays on even at low intensity there is still a problem on the board. I disconnected the left channel output power board because something was burning. When I did my second test without the defective board, the light stays off. Now I will continue and troubleshoot this defective board.

@markanderson8066

2 жыл бұрын

We've used this for vintage tube radios - when they were new, lol! Great tip. Some make a box with a bulb socket, power cord, and receptacle to plug in the device to be tested. NOTE this ONLY works with incandescent bulbs! Do not use LED bulbs!

@sebo0855

2 жыл бұрын

@@markanderson8066 Shango066 uses this approach too, and yes, incandescent bulbs is mandatory because they act as high power resistors with soft current limiting due to filament temperature characteristics.

@jamesatkinson6480

Жыл бұрын

I used that technique, soldering a 75W incandescent light globe to two insulated wires, and putting it across a blown fuse. I called it an 'economical PTC thermistor'. (PTC - Positive Temperature Co-efficient (of resistance)).

I have so much fun watching your repairs. Comments are fantastic, it's like reading the pages of a magazine. I learn a lot with the vintage HiFi. And they are beautiful also. No plastic. Amazing.

Wow ! Nice going with the very detailed step by step diagnosis and repair of the stereo amp. Your attention to detail is impressive. You are definitely a pro at this high skill electronic repair. Thanks for sharing this quality demonstration for others to learn from and enjoy on KZread.

WOW! What a fantastic channel. Incredible, detailed, work. Talk about going the extra mile. I have six, 70s-80s-era solid state amps and they each need a little bit of help. Thank you so much.

Way back in time, I had a customer bring in an amp where they had tried 4 or 5 fuses to "fix" an amp. By the time they had finished there where blown transistors all the way back to the pre-amp / driver stages. That job was _fun_ Cheers,

I love watching your videos, I have absolutely no clue what you’re talking about because I am not that technical but for some reason I just like to learn. Not like I will ever use this information but it’s just fun to watch. I like watching you get in there and soldering putting components into boards. The grunt work you know what I mean

Very cool, D-lab. Moment I saw the burned resistor, I thought exactly all like you. Thanks for taking it home in the video.

Absolutely hooked on these how to identify problem solve and repair audio equipment, and going about it the correct way by being safe and showing what test gear is needed

@BenState

2 жыл бұрын

also check out Mr Carlsons lab

Hi Terry, thanks for sharing your vast knowledge!

Time and patience is what shown here and very professional 👍

I've been watching various vintage electronic repair channels for 4+ years now and only now have I been recommended this video. I love you style and attitude. You aren't grumpy or preachy like some of the older repair guys and seem to be all about having fun. That's what it's all about in the end isn't it? If you aren't having fun then why are you into this hobby? I quit drinking over a year ago (not that I had a problem per se, but it really wasn't benefiting my life in an appreciable way), but seeing you enjoying a glass of wine really sold me. It really conveys the laid back nature of your channel and earned you a new subscriber. The alien skit pushed it over the top and I'm gonna head right to your patreon page and throw some money into your wine and cracker budget. Hopefully it's enough so you can afford to upgrade to a wine, cracker and cheese budget. If you prefer an aged hard cheese or a young runny variety you can't go wrong with a nice manchego or brie, respectively.

@georgecrosscross8253

10 күн бұрын

Happy comments, totally agreed!

@trippmoore

9 күн бұрын

@@georgecrosscross8253 glad you replied after a year. lol. I think I was never recommended another of your videos even though I subbed and I completely forgot about it until now.

Very good repair and instructions. Thanks for posting this Terry.

Excellent!! Thanks for your shared precise knowledge!

Beautiful bringing the devices into life again, this is an art.

Yeeeehhh man Realistic is live one more time!!!!! Good repair Tery!

Good catch on the diodes. Also, very good point on checking further into the driver circuit. I’ve repaired a couple of amps that had collateral damage like that.

Absolutely fantastic, great humour and solid use able content. I took notes and learned so much! Thank you, I'll be checking out your other vids. 👍

I appreciate people like you sharing your knowledge. It is so rare to find anyone that can repair solid state electronics, I've resorted to working on my own. Thanks for your help in turning an industrial controls guy into a 1/4 funtioning solid state repairman. I've got a Sansui G8000 I want to hear before 2 years... I may kick the bucket before then .

Well done. I'm trying to learn basic electronics; theory is one thing... but there's nothing more instructive than watching an expert fix broke stuff.

Very helpful info, especially about checking the power supply diodes. I might have had to learn about that one the hard way. Nice sounding little amp.

Another "save" in the column!! Wish I had the benefit of this knowledge 10 years ago. I bought a Sony receiver/amp in 1980 when I was 18. A very good unit. It finally bugged out on me & all the options to repair it were so obscenely expensive at the time. It met the trash heap.I still look for something close to replace it with. Thanks, Terry!!!

I checked the dictionary for the word ''professional'' and I saw your picture.

Thanks, I enjoyed watching you at work.

You sir are very informative as well as entertaining!!!!!

I'm glad to see you tested all of the transistors. I've seen many shorted driver transistors take out the finals

I loved this video-very informative, funny as well. Great job!

Great video. Very informative. Looking forward to more. Thank you for doing this!

Great video Terry. You put a lot of work into these!

I like Mr. D-lab's attitude and presentation style.

Dang! Really blew a lot of stuff on that one. Good thing it was sent to you to repair! Changing those caps was a very wise thing to do. Keep up the excellent work Professor!

Well done! I bought a used Marantz 1030 in the seventies... loved it!

Learning so much and your explanations are really lucid. Thank you

Thanks Terry! Nice work!

Great job. Like that you accept the challenges!!

You are great Terry. Thank you very much for this informative video!

Cool to see a solid state repair. It makes sense that the caps work just like a tube amp, but I'd never seen one described like that. Thanks for bringing us along on this one.

An enjoyable watch. Thanks for posting.

Nice video as usual! Thanks for sharing!

Wow I have an old JVC boombox (RV-NB20B). This was my outside source of music for more than 10 years. I loved it and bragged about how tough it was and how good it sounded. It quit working about 7 years ago. When I turn it on, the red power light comes on for a second and then there is a static pop from the speakers, and it shuts down. I have kept it with me always hoping I would come across a proper electrician who could fix it. I wish your were close by. I bet you could fix it. I'm old enough to remember when most towns had a shop where you could bring your electronics to be repaired. Now-a-days folks just throw the unit out and get another one.

I have to say much thanks for your repair videos, one of the best if not the best.

Wow this a clean looking and laid out unit , My Fisher TX500 receiver is full of wires soldered everywhere.

this is SOOO great! thanks much for posting, great info.

Excellent video Terry

Thank you for producing this video! ! Love it. I am learning to be a sound tech repair.

Very detailed explanations. Great video!

I was doing Amp repair back in the day we were quite busy at times surprised that quite alot of people looking at these repair vids these days

this is awesome info. i wish i'd watched this before jumping straight into swapping my main transistor pair. i didn't realize it was fine to check for component shorts with the components still soldered onto the board. thanks again

thanks for a very professional job. guys like you are hard to find. keep up the good work

That was great. I'm new to this and it was very well explained. Thanks

Very good troubleshooting step by step!

Thank you for getting me started.

Great choice realistic are way undervalued. 👌. Thank you very much for your knowledge 🙏

The 70's and 80's amps are super but man, the 70's and 80's guitar notes......just awesome! PS:- Electronic repair instruction wasn't too bad either.

Nice one Terry. I actually thought you were playing The Who’s - Behind Blue Eyes in the test. I love these 70’s and 80’s amps. Appreciate all your tips

@bigmac965

5 жыл бұрын

Sounded like Emerson, Lake, and Palmer to me. I need one of those royalty-free CDs.

Great Video Terry!!

Brilliant! I enjoyed that - tools for the job!

Nice repair, very thorough. I know what you mean about using generic replacement transistors, sometimes they don't work properly, I've experienced that in the past. It is best to use exact replacements whenever possible.

Thank you for such a comprehensive and clear explanation. And kudos for the mini movie troll abduction.

I should have been doing this my entire life! Now I'm at the end and not enough time to get back in it! Good job!

Another cool repair video from D-Lab Electronics

My new fav channel! Glad I found it.

Extremely good job. Congrats Sir.👏👏👏👌👌👌

Sounds good! Nice to see some solid state audio here, most electronics are tube oriented.

They are really good sounding amplifiers.

Love all the comments and experience you bring to the channel . I am glad to see the transistor amps and recievers ..

Good troubleshooting info in this video. Good job.

Thanks for all the repair/troubleshooting detail. That was really helpful. I learned a lot. I've got a Pioneer VSX-920 Audio Video amplifier from 2010 that has issues. A neighbor was going to throw it out. Hopefully, I can solve the DC 003 error code problem and get it going again. Regards, Tom

@Euthymia

Жыл бұрын

Probably already done it by now, but any electronics made in Asia between 2005-2007 (basically everything) is likely to have classic "cap cooties" issue. The Asian cap manufacturers got a bad recipe for electrolytic that lowered the life of the caps they made. Millions of them. Whenever you see a TV or monitor from that era that powers on for 5 seconds and shuts off, it's those caps. $10 fix in parts.

Amazing repair.

Initialy i wanted to learn whats wrong with my older amp, which is way newer then this one. Stayed for the great content! Subbed!

This was a great and very detailed video.

I broke down and bought myself a vacuum desoldering gun on sale a while back, it wasn't cheap but it saves a ton of time replacing parts on these old units.

Boy, you were lucky. I don't think I've ever gone thru an integrated amp of that era with blown outputs that didn't also take out the phase splitter or driver transistors.

@saddle1940

4 жыл бұрын

And used an out of manufacture STK module!

Nice!! Very Realistic approach... :-)

Great video, thank you!

its a beautiful work, thank you for the update, Warm Regards from Australia

Outstanding video.

Very nice Sr Terry, thanks i like your job, i'm study audio amplifier.

Excellent video my good man.

Your technical knowledge is inversely proportional to your sense of humor. Stick to what you're good at. ;-) Thanks for the tips. I wish you all the best.

Hi teacher very very nice interesting, your age same my father I love it & I love your video too I got more technic in trouble shooting amps,but don't forget your wine really refresh your mind, thank you for the video too. More power & God bless.

clean and perfect work

Very efficient repair!

Very nice job.

Very educational fun. Thanks!

I am totally impressed! Another tech who actually knows how to test components, and not use "universal" replacements. I use the 105C caps wherever I can in my repairs. They just seem to have a longer life. OEM semis all the way, if at all possible, especially on Sony products. Did you check the bias pot for opens or shorts before firing it up? I have found a number of times that bias pot is fried. I also check any bias diodes, transistors and resistors. Over the years I found that in the DC coupled amps, I replace the drivers as S.O.P. I normally clean off all the old heatsink compound as sometimes it gets pretty hard. The old clear compound often took a chisel to remove if the part had really overheated. Great video and explanation. You got a new subscriber. Thanks.

@generalcurtis3lemay180

4 жыл бұрын

2SD371 finals are a TO3 package so the heatsink thermal compound doesn't go on the metal, there's a vintage mica or recent cloth washer between them. All the old thermal goop needs removed. The old filter cap is 70 volts and D-lab puts in an 80 volt. It could be D-Lab's know-how is 'monkey see, monkey do'. There are different types of snap-in caps and some take more current than others. Should we trust D-Lab with vintage audio? He's no expert, might be military radio trained. 🤠

@wedoshotz6645

4 жыл бұрын

@@generalcurtis3lemay180 All e-caps are rated by value & voltage, along with thermal tolerance.......nothing related to current. It's SOP to put in an equal value replacement with a little higher voltage rating. As a matter of practice, unless I'm using sil-pads, I clean all surfaces & re-apply fresh thermal compound to both sides of the mica insulator. But in a lesser powered unit with an ample heat sink like this, it could be excused.

Awesome. Thank you, I really appreviated this. Going to share this video with a friend. B.

03:25 "...and then the Circus Board..." Priceless!

Good fix great sound

You are the best repair electronic engineer. I was the hobbiest electronic person.

That was great Terry, excellent points about the caps and the diodes if one is trying to fix something like this. An especially smashing job of getting rid of Dick as well !

Good work D labby !

i have no idea what you are talking about or doing but i still find it very fascinating.!!!! 👍

Thank you Terry !

I'm trying to fix up my Sansui Au-717.. this helped a lot!

Very much informative... learnt a lot.. thanks..

At 9:00, an analog ohmmeter will check the transistor junctions, even *in circuit*, typically giving a reading of about 10 to 20 ohms between base and emitter, and base and collector. Short circuits are typically to be found between the emitter and collector. I didn't watch the whole video yet, but it bears mentioning, in case Terry doesn't, that if there is a polarized electrolytic capacitor used as a feedback capacitor for the differential amplifier input circuit, it should be changed to a bipolar capacitor. Sometimes those feedback caps get hit with a backward voltage surge as the power supplies are energized or depleted , leading to a damaged or, eventually, blown cap . An electrolytic bipolar cap is fine; or at the very least put a small film cap across it. I'm surprised this unit doesn't have a removable bottom panel, most units of its era did and do.

Great video !