Thanks for the video! You most likely saved me from breaking the clips and damaging my mirror cover!

Thank you. This makes vinyl wrapping the mirrors much easier 👍

Great! Thank you very much! I just replaced LED lighting with new one. Broke lower cover parts, but not a big stuff.

Thanks, this helps a lot, I went to go put led puddle lights in mine and I pulled one of the wires out of the connector and I can’t get enough grip on the wire to pull it out to crimp on a new connector

Nick, you are just amazing 👍

Thanks for the thorough demonstration

Just so you know, the tabs on a 2016 Fusion are hard plastic, not soft plastic. Lifting up the tabs as shown will snap the tab off. I learned this on the first one. And after the top three are done, the mirror has a 4th tab on the bottom, so one has to somehow wiggle the casing off very careful or it too will snap off, just like it did for me. And the is another 1/2 tab on the windshield side as well. Just an FYI.

@texassherman7093

2 жыл бұрын

On the mirror itself?

@hunterjohnathan1

Жыл бұрын

Just broke mine off 😢 wish I would’ve seen this comment sooner lol. Did it affect anything having that bottom tab broken off?

Thank you for your video! It really helped!

great video! Very helpful

great video...thanks..you help me alot

Thanks for the info and help!

Great vid. Thank you

Well done thx buddy 👍

Thank you for saving me $25 in a garage

Should I do this to replace the turn signal light on a 2015 mirror? (It was hit by a door)

Thank you!

thank you !!

And how do you remove the bottom part going to the door ?

👍🏻thank you

can anybody tell me how to replace the plastic mirror frame on my mk 5 mondeo

Sweet, time to black my mirrors

Hi! Could you please to tell me how I can disassembly mirror frame from mirror arm?

@Nickthecarguy

4 жыл бұрын

That's a good question I havent figured out either I tried everything no luck

Thank u... Apparently my car is an accident magnet.. 2 doors... and Now a mirror all within 4 years lol

Do you know if the procedure is the same for the 2010 Fusion?

@Nickthecarguy

4 жыл бұрын

No its probbly not the same I'm not forsure how to remove the cover on the 2010

Does anyone know if the 2017 is already wired for BLIS and heated mirrors? Mine didn't come with it, but I'd like to add it.

@Nickthecarguy

3 жыл бұрын

You will need new door harness and you will have to wire the blis module from scratch the module is not pre-wired on the car

My cover doesn’t come all the way off, it seems like it’s being held on at the lower (inside) corner ( on the door side). Is there another clip to push or something other than the 3 along he top? The light along the side of the mirror assembly got broken in a car wash and I’m tryin to replace it. Seems like I may have to take the lower cover off too? Any ideas? Thanks!

@Nickthecarguy

4 жыл бұрын

There kinda like a retainer tab that pop off but no tab to release it you have to kinda work it out after you get the three tabs on top disengage

@dstarok

4 жыл бұрын

Ok thanks nick

I need to find out how to replace the black frame part of the driver side mirror. I've managed to get the mirror mostly disassembled but can't figure out how to reach one of the screws. Do you have a video showing a total disassemble of the driver mirror?

@Nickthecarguy

Жыл бұрын

That unfortunately I could never remove I've tried but not luck

@yAzraelMk2

Жыл бұрын

Same here, did you find a way to do it?

I have a 2020 ford fusion energi hybrid..the plastic cover and frame has been badly cracked ...bought replacements...got mirror off ..easily...the plastic just fell apart...got 3 screws out but 1 screw is in opposite direction...just a tiny piece of plastic still attached. How can I get it out? then...I can put the 2 new cover and frame in..reattach the wires to the mirror....

@deborahfrederick3543

2 ай бұрын

I cannot afford the cost for auto body or anyone to fix this.

Never heard it called flat bladed screwdriver lol where are you from?

where did you get the glass that has the BLIS and the convex mirror? I don't know why manufacturers don't do that more often, it makes so much sense.

@Nickthecarguy

4 жыл бұрын

These came off of a 2015 ford mondeo it came all the way from poland

@zachtravers1

4 жыл бұрын

@@Nickthecarguy thanks! I'll have to keep my eye out to see if I can find the glass and see if I can get my hands on the sequential turn signals since they're out of stock.

Nick my electrochromiyc mirror dosent work, how it be can repair

@Nickthecarguy

4 жыл бұрын

You might need a new glass. Does your rear view mirror dim?

Is this process the same on a 2018 Edge?

@Nickthecarguy

Жыл бұрын

Yes

👍

***** WARNING ***** Do not follow this video. Along with the three tabs on top, there is a fourth one about 2" in underneath that must be pressed upwards to release the bottom of the cover. The reason Nick's comes off so easily is he's already broken his. Once broken, the cover becomes dangerously easy to remove and can simply be pulled off - Expect it to fall off and as such needs replacing. I found this out the hard way! Don't be like myself and Nick.

@Nickthecarguy

4 жыл бұрын

I appreciate the comment mine havent fallen off yet since I've made this video my bottom tab is still intact

Nice but way to much talking! learn to hold the camera a little better. Thanks.

Thank you , very helpful