How To Remove & Replace The Captive Bolt On A Weed Eater Clutch Bell!
This simple repair Stihl 2 stroke weed eaters can save you a lot of money and frustration!!
TOOLS I USE:
Engine Tachometer - amzn.to/3TE48GZ
Mityvac Pressure & Vacuum Tester - amzn.to/3vysI3V
Gasket Maker - amzn.to/4bIiygR
Vessel Screw Drivers - amzn.to/3ISewG2
Brass Hammer: amzn.to/3xkyuH6
Stanley Stump Vice - amzn.to/3waHuOw
Stens 750-120 Carburetor Adjustment Tools- amzn.to/4atkBV5
Powerbuilt- backtap - amzn.to/49I9305
Forceps - amzn.to/4a2ud9v
Zoom Oil Bottles - amzn.to/3TWZV2t
Mityvac Compression Tester - amzn.to/4aimaFS
Bondhus Hex Keys - amzn.to/3J2m8FL
Klein MM400 multimeter - amzn.to/3PI3Y02
Stahlwille Combination Spanners - amzn.to/3IY6fQI
Milwaukee 12v Impact Driver - amzn.to/3VEuxH4
Milwaukee 12v Impact Wrench - amzn.to/4aPESVd
Milwaukee 12v 90 degree Grinder - amzn.to/4czLiJp
No-spill gas can - amzn.to/3TDfWcb
Any links to products are likely to affiliate links and I may earn a small commission from qualifying purchases with no additional costs to you. Thank you!
#2stroke #enginerepair #smallengine #stihl #husqvarna
Пікірлер: 67
Great repair video Tom well done 👍
@VintageEngineRepairs
Жыл бұрын
Thanks buddy!!
Good job mate. We have all broken that screw, this will save buying a new clutch housing.
@VintageEngineRepairs
Жыл бұрын
Thanks Bill! Spot on :) the last time I rounded the Torx bit thankfully not snapped it, but I wish I knew this then before it ended up in the bin!
Nice save Tom thanks for sharing !
@VintageEngineRepairs
Жыл бұрын
Thanks Bill!!
Great tip Tom
@VintageEngineRepairs
Жыл бұрын
Thanks Al :)
Never knew that Tom, great Tip!!
@VintageEngineRepairs
Жыл бұрын
Thanks Kenny and thanks for encouraging me to make a video!
@KensSmallEngineRepair
Жыл бұрын
Remember Tom, like the Repair Specialist Craig says: "Knowledge is Power!"
@VintageEngineRepairs
Жыл бұрын
@@KensSmallEngineRepair so very true Kenny!
Top job tom have one in that has the same problem this will save me some time thanks mate 👍
@VintageEngineRepairs
Жыл бұрын
That’s great to hear Mark! Pleased this helped and was of good timing :)
Good vid there mate, glad it helped, now you need to explain to your viewers what happened to that circlip when you first removed it, :), and why when fitting it, you had your finger over it. On some circlips, I put the piece that has the circlips inside a plastic bag if possible, and if it flies off, the bag contains it.
@VintageEngineRepairs
Жыл бұрын
Thanks mate and thanks for your help, this would be in the bin if it wasn’t for you! Yes! Such a good point. For anyone reading this, the thing went flying the first time even with my thumb covering it. Spent 10 minutes searching. Great tip with a clear bag mate! I’ll use that in future :)
@Big_Johns
Жыл бұрын
🤣🤣🤣
@KensSmallEngineRepair
Жыл бұрын
Thats why we sometimes call them Jesus Clips! When they fly off into the abyss, we yell Jesus!!
@johntrainssmith1475
Жыл бұрын
@@KensSmallEngineRepair Circlips are proof of a 4th dimension existing.
Nice work Tom.
@VintageEngineRepairs
Жыл бұрын
Thanks Barry!!
Excellent,now I now how to remove,tanks to you
@VintageEngineRepairs
4 ай бұрын
You’re welcome, glad it helped 👍
Brilliant mate thanks for that
@VintageEngineRepairs
11 ай бұрын
You’re welcome! I’m pleased you found it handy :)
Good to know thank you, won't be throwing the clutch drums away any longer 😉
@VintageEngineRepairs
Жыл бұрын
Me too haha
Excellent video, I just recommend using an Internal tooth lock Washer to prevent the screw from loosening.
@VintageEngineRepairs
2 ай бұрын
Thanks for watching and yes, you can do! I just use a drop of Loctite :)
Very good video ( I have a same problem like you ) it fit perfectly.thank you .
@VintageEngineRepairs
Ай бұрын
Glad it worked out:)
Te felicito, el unico video de este tipo de pieza😊
@VintageEngineRepairs
2 ай бұрын
Glad you enjoyed it :)
Amazing video. Great advice! I love your novel way of looking at these problems. My issue is I accidentally rounded the torx screw head and can't figure out a way to get it the heck out of the drum so that I can use your method to rebuild the drum. The shaft on my Ryobi 875r 4 stroke is way too narrow to get a screw extractor down there. I'm guessing the only option is a long skinny left hand drill bit, but I wont be able to see what i'm doing down in the shaft and I don't want to damage the crankshaft threads. I figure if anyone can figure this out it would be you. Might make a good companion video to the rebuild one. Cheers
@VintageEngineRepairs
2 ай бұрын
Hey :) thanks! You can try put some CA glue on the end of the Torx bit, let it set up and carefully see if you can free it? It’s unlikely, but it’s about the best I can come up with!
@jeffreyhornstein4887
2 ай бұрын
Great idea. I never even thought of that. I'll give it a try. Thanks
Good stuff Tom - you don't learn that in school 👍👍
@VintageEngineRepairs
Жыл бұрын
Thanks Claus buddy :)
i have a stihl fs 38 weed eater that I change the clutch, I feel that the bushing in the clutch bell is lose cause the bell to wobble. It does not fit like one in the video. Do you know if this part can be bought separate without buying the hold clutch assembly? I
@VintageEngineRepairs
10 ай бұрын
Possibly!? You’ll have to find the parts manual (google) and it will show you :)
The company that make that trimmer should hire u to make things better........ good job...a 10-10...😉
@VintageEngineRepairs
2 ай бұрын
Haha thank you :)
How on earth did you manage to get the screw out of the crank shaft. I just broke one off in mine and would really appreciate some advice on how to get it out.
@VintageEngineRepairs
3 ай бұрын
They should only be snug and maybe a touch more, if they’re hard to remove it’s possibly rust. Be careful, heat it up and use penetrating oil. Then drill a hole through the bolt and use an easy out :)
Good Job 😄💯
@VintageEngineRepairs
2 ай бұрын
Thanks :)
Nice tip Tom, how long did it take you to find the circlip the first time you tried popping it out?? 😲
@VintageEngineRepairs
Жыл бұрын
10 - 15 minutes on my hands and knees wjth a magnet 🤣😂
@Big_Johns
Жыл бұрын
Well at least you found it, I have some still hiding to this day.
@VintageEngineRepairs
Жыл бұрын
Same 🤣 we’ll I’ll find them one day mate! 😂🙄
Hello Tom 👍
@VintageEngineRepairs
Жыл бұрын
Hello Mr Luke!
Tom you were very unlucky to break the screw, the hundreds of these I've removed over the years I can't say I have had this happen. It probably will now I've said that. lol..
@VintageEngineRepairs
Ай бұрын
Haha if you do you know the solution 🤣
@TGMForum
Ай бұрын
@@VintageEngineRepairs Yeah, I'll just fit a SH one, we have loads laying around. 😉
I had no idea that this was possible
@VintageEngineRepairs
Жыл бұрын
Me neither until today 😂
@haneyoakie14
Жыл бұрын
@@VintageEngineRepairs excellent tip. Thank you!!
Much thanks ! Cut off the last one
@VintageEngineRepairs
7 ай бұрын
You’re welcome :)
A poco venden ese perno de bronce que miro allí
@VintageEngineRepairs
Ай бұрын
Very good!
@user-cn3vg3hj2b
Ай бұрын
Gracias maestro saludos
To me the circlip went in backwards
@VintageEngineRepairs
Жыл бұрын
I don’t recall which way it went but it went the way it came out lol
thumbs up skip
@VintageEngineRepairs
Жыл бұрын
Thanks mate :)