Very helpful and informative. Thank you for making this!

Great information! Thanks for sharing!

@EllafulDeco

11 ай бұрын

Thank you for watching! I'm working a lot more efficiently with this little machine around!

This is a very informative video. Thank you so much for sharing. Great job!

@EllafulDeco

10 ай бұрын

Thank you for watching! 😊

You did great! First time I’ve heard about the airless chamber for resin. Thank you for the info. 😊

@EllafulDeco

11 ай бұрын

Thank you so much for your comment!😊 This machine is certainly really helpful for what I make!

Thank you for the tips!!

@EllafulDeco

11 ай бұрын

Thank you for watching!😊

Good job. Entertaining for functional reasons but also because of your natural interest and intelligence

@EllafulDeco

6 ай бұрын

Thank you for your feedback!

This was great, full of information and made me think about the possibilities of flash curing and less work time. 😁 Very helpful

@EllafulDeco

11 ай бұрын

Thank you for watching and thank you for your feedback, Grace! I had the resin flash cure on me 3 times before I got used to the timing😅

Great information.

@EllafulDeco

5 ай бұрын

Thank you for watching!

I liked your video - great info. I ordered the Airless - thanks for the discount code 😊

@EllafulDeco

11 ай бұрын

Thank you so much! I'm so happy to hear that you found this video helpful 😊

@lovestobead

11 ай бұрын

Did you buy it on Amazon? I can’t find where to put in the code?!

@oslovejulie

11 ай бұрын

@@lovestobead when you check out not buy by swiping. On check out page under your payment info credit number etc there will be in small writing use gift card, promo etc code - open that and scroll to the bottom to add your promo code. Good luck

Hi Ella great video comparing the 2, iv just ordered a vacuum chamber, thanks for sharing 😍 ❤ xx

@EllafulDeco

8 ай бұрын

Thank you for watching, Michelle! I'm excited for you😁 A vacuum chamber is really helpful for thinner resins and larger batches!

@michelle_resinrebel

8 ай бұрын

@@EllafulDeco Thank you 🥰 ❤️ xx

Thats different sealing on the vacuum chamber as my lid simply sits on - the silicone forms the seal against the top of the lower stainless steel pot. Also the single stage 4CFM new vacuum chambers, 13.5 litres (3.5 gallon) in size, was AU$150, or just over $100 USD off ebay, and thats about half the price of the resiners machine here. Thanks for the video, it was informative

@EllafulDeco

11 ай бұрын

Thank you for watching! I’ve tried the lid sitting on top of the pot when I first got it and I think it was having trouble releasing the pressure so that’s why I do it like this. Price is definitely a factor as I mentioned and it seems like that varies with location. At a $100 difference, it makes a lot more sense to get the vacuum chamber! Both are great and gets the job done 😊

@lechatbotte.

18 сағат бұрын

The resiners has dropped in price but some people are afraid of the vacuum chamber

Great info! I went to order and couldn’t find where to put the coupon code…? Any suggestions? Thanks!

@EllafulDeco

11 ай бұрын

Thank you for watching! The coupon code spot on Amazon is in the payment section. I believe it's gift card/promos.

Thank you for the info but can you color your resin before using the airless machine. Thanks

@EllafulDeco

11 ай бұрын

I have tried it after mixing in mica powder and before pouring. It worked, but it seems to have taken longer for the bubbles to rise completely. You may get better results with liquid pigments and tints. I don’t really use those for coloring (I like a little bit of shimmer from micas), but I will definitely make note next time if I do.

@shane5647

11 ай бұрын

@@EllafulDeco Thank you

Can i use the Resiners Airless for my 1:1 ratio table boat resin?

@EllafulDeco

5 ай бұрын

No, table top resin is thick and the work time is too short for the machine. You might have to look into a pressure pot for that, but I’m not too familiar with pressure pots.

You mentioned you use another Total Boat resin for flowers; which do you use? The resin for this was perfect. Beautiful results

@neviawashington5779

10 ай бұрын

Edit. I watched another video ( not this one)😂you made a sphere design. It was beautiful

@EllafulDeco

10 ай бұрын

I used TotalBoat’s High Performance resin that I mentioned in the beginning of this video for the pieces shown since they’re thin (~1/4”). It’s good for flowers for me, but just doesn’t allow me to pour too deep. For flower preservation, larger blocks typically 3” deep, I use their ThickSet/ThickSet Fathom. You can check out some flower preservation videos that I have on my channel to see how I work with them🙂

@neviawashington5779

10 ай бұрын

@@EllafulDeco thank you.

@neviawashington5779

10 ай бұрын

I ordered the resin. Wish me luck

Beautiful awesome work💞❤💟💝💝💞❤💞❤💟❤💛❤💞❤💞💖❤💛❤💛❤💖💞💞❤💞

@EllafulDeco

10 ай бұрын

Thank you so much! ❤️

Will resin form more bubbles as it cures?

@valasiakantarzoglou628

11 ай бұрын

Also how did you keep the lemons yellow in that resin letter you showed?

@EllafulDeco

11 ай бұрын

The vacuuming process eliminates most of the bubbles before you pour. When you pour, you will introduce a small amount of bubbles (as you would normally) and if you use any inclusions like the fruits and flowers, that will also introduce bubbles into your piece. You will still need a heat gun to pop bubbles and should stick around until the end of the work time of your resin to pop any bubbles that rise to the surface. It will be a lot less, but there can still be bubbles. As for the letter, the fruits are actually orange slices and they are dried.

I find my resiners unit is useless. No matter what resin I use it still has thousands of micro bubbles in it.

@EllafulDeco

11 ай бұрын

You can try a vacuum chamber and if that solves the issue, maybe you have a faulty unit. If not, then your resin may not be compatible with the vacuuming process. You may want to look into a pressure pot for bubbles, but I’m not too familiar with those myself.