Thanks so much. My Sub's bezel had stopped turning easily and was not making the clicks. I followed what you did, and there was a ton of dirt under the bezel. Took a few tries to get the spring in just right, but entire project was less than 30 mins and now it is PERFECT again. Just a word of caution to ohters trying this, be sure you fully seat the insert into the bezel. I caught the fact mine was not fully seated and re-did it successfully and got that reassuring loud click as it went down into place. Would have been very bad to have lost the insert. You saved me $300 and a month without my watch. Many many thanks!

You just helped me fix my 14060! Thanks a bunch!

@sherminator34

Жыл бұрын

Co

Thanks for sharing, interesting to see the difference between a high end watch compared to something much, much cheaper.

I think the shine on the aluminum bezel looks so cool over the porcelain

Very well-explained, I learned a lot. Thank you for sharing.

Good video ... step by step ... easy to follow. Thanks

Best video on how to remove, clean and install the Rolex bezel. In particular I like the shots on removing / put back the spring. I am not a watch repair person, so the video helps a lot. My Rolex submariner bezel cannot turn smoothly. I tried cleaning from outside, put on some oil and finally WD 40. Nothing helped. Removing and cleaning the bezel did the trick. So glad.

Thanks for the great video. Just cleaned my Submariner Blusey bezel today and it went from not clicking at all just stiff ‘click less’ movement with sloppy backward slippage to very silky smooth firm clicking unidirectional motion without any back movement whatsoever. Feels and sounds new again. Now if I could just learn how to laser weld to fix the big dent I made in the side of the case by dropping it 10years ago that would be splendid.

@DAVD305

10 ай бұрын

I think leave it dented, after 10 years that’s your watch with character now. Unless you gonna sell it or so. Other option hunt down a case and when you are ready to maintenance your watch ask them to put all in new case. Will loose case serial only thing.

@plexiform1973

10 ай бұрын

@@DAVD305 never going to sell it. Will give it to my son one day. Maybe you are right, will leave the dent alone.

@JOE-on4pi

10 ай бұрын

Thank must have been a big drop to dent stainless steel! I feel the same way, I have a couple light scratches and a tiny chip on the crystal, only visible under a jewelers loop. I too am giving it to my son one day, so he’ll inherit the imperfections as well!

@eduardwalhout1740

5 ай бұрын

@@plexiform1973 exactly. make a few more dents! the watch will be much more meaningful to your son if you can see it has lived your life with you. whats a new rolex? anyone with some money can have that...

Great video 👍 thank you for sharing

Thanks for the vid!

6:18 Thank you for this video! I just found out that the Tudor black bay 41 without the rotating bezel is my dream watch! I got super excited when I saw that submariner without the bezel!!!! 😍😍😍😍😍😍😍

@panosvrionis8548

2 жыл бұрын

See apocalypse now 😋😋 Curt's wears exactly the same

@resjon7981

2 жыл бұрын

Pity Tudor never made a 39mm version.

@bigbrotherwatchesdannyboy306

2 жыл бұрын

@@resjon7981 who knows! Maybe it will come one day 👍👍👍

@resjon7981

2 жыл бұрын

@@bigbrotherwatchesdannyboy306 Hope so as I recently sold my BB36 because it was just a little too small and the 41 is slightly to big for that style of watch.

@bigbrotherwatchesdannyboy306

2 жыл бұрын

@@resjon7981 I hope it for you my friend. 🤞😉🤞 time will tell!! 👍

Thank you for the video! My bezel was really tough to move, so I’ve watched your video - voila the bezel of my 16600 is smooth again. 🙏

@2K9s

Жыл бұрын

Supposed to push down while rotating the 16600 bezel. 👍

Leaving the tap running ..really such a waist of water ...But appreciated the info regarding Bezel removal .Thankyou

I know it’s a year later but is the ceramic bezel insert attached the same way? Thank you 🙏

it seems very easy. Thanks.

@watchmakerjd8525

3 жыл бұрын

Thanks for watching😊

Way to make this look super easy. I'll give it a try. 👍

Is it the same process to swap of the bezel for aftermarket bezel?

Excellent video, very helpful. Thanks. It’s difficult to put the spring back though. Is it the 90 degrees angle side of the spring which goes in the little hole?

Is there any different technique with the GMT-Master II

Hi! This is a 16610 correct? I thought on a 16610 the little spring is located at the 1oclock position not the 6? Or am I mistaken?

Great video ill try to fix my 5 digit sub bezel on it rotates both ways maybe I need a new spring

If the 60 minute triangle with pip has to be at 12:00 to replace bezel, why did you put put it at 10::00 to remove? Mine comes back from Rolex factory servicing and spins freely but very shortly afterwards becomes difficult to turn again. I am going to give this a try but wont remove spring.

How much does this differ from the removal of bezel on the certina pro action diver powermatic 80 the bezel is jammed

Good video but I'd tape up the blade instead.

@Mikesrolexes

5 ай бұрын

Have you tried that?..just curious...makes sense..

Nice sir

Does anyone know if the ceramic bezel insert removes the same way by hand?

TY,,,,,,WOW 1st class incredible very interesting super kool ,1st class great info.,, AAAAAAAAAAA++++++++++++ again great video I liked it a lot ,keep up the great work

My batgirl bezel turns without clicks, what can i do to it

Oddly enough and off topic to the point of this video, but the watch looks good without the bezel as well! Looks like you took a submariner and turned it into an explorer 😀

@TheEx77

2 жыл бұрын

the marlon brando way

Is this procedure the same for a sea dweller? From 1995-2000’s

@jsusna1972

2 жыл бұрын

I have the same question. I want to put a green bezel on a Sea Dweller, ref #16600. Is the click spring always located in the same position?

I just attempted to replace a black insert with a green one. I removed the assembly with no problem, but could not separate the insert from the bezel as easily as depicted in the video. Are the inserts sometimes glued in? If so, why and how would you remove the insert in that case? Not wanting to damage anything, I ended up taking it to a watch repairman.

@watchmakerjd8525

2 жыл бұрын

If the insert and bezel are Rolex genuine, they can be separated by hand. Glue is not used there because it is the principle of detachment. If you press the inside of the insert with your hand, the insert will fall out.

@jsusna1972

2 жыл бұрын

@@watchmakerjd8525 I'm not what you meant by "principle of detachment." So then there is a chance that the insert is not Rolex genuine and was therefore glued in? If you had one that did not simply fall out, would you be able to somehow separate them using a heat gun, assuming it must have been glued?

@oaktree1628

Жыл бұрын

@@watchmakerjd8525 great video! Is the vintage GMT Master II (16710) the same in terms of removing the bezel and location of the spring?

My bezel froze spinning left, awesome video....but I may not do what you did?

Looks like a TC LV Submariner. The crystal retaining ring spring are always installed opposite of a genuine.

@timmer92984

2 жыл бұрын

That makes no difference, the click spring location is a matter of where the hole is oriented when the crystal retaining ring is pressed. Most people press the retaining ring so the click spring is oriented over the upper right hand lug to make it harder to lose the click spring when removing the bezel.

This is like watching horror movies 😅😅

If my bezel is one click off from being centered, can I do this to re-center properly?

@mtbbiker6401

Ай бұрын

yes. requires removing the bezel insert and re-align.

Could you do this with a bb58 please

Why is my click spring at around 1 o’clock position?

Where can I get the bezel??

Is that bezel insert just holding by friction ? That is cheaply made. You should try to dismantle the bezel of a Citizen Aqualand C022 or C520

@mtbbiker6401

Ай бұрын

Most watches have a bezel retention spring.

Very useful video, no waffling on about crap…….Very unflattering watch without the bezel……..cancelled from my wish list….

Nobody noticed his fingers glouses lamo 😂😂😂

@RabbitWatchShop

10 ай бұрын

oddly shaped thumbs, too.

I don't get it - my vintage rolex doesn't have a hole for the small piece of metal to go in

Super! 😀

Does this also work for Tag Heuer? Also what about a bezel removal tool? Also I would suggest removing the movement and using a ultrasonic. Your living dangerously placing it under water like that assuming the crystal has no cracks 😅

is the same with daytona?

@watchmakerjd8525

3 жыл бұрын

Daytona has a different bezel structure. Thanks for watching😀

@JohnAbuklau

3 жыл бұрын

@@watchmakerjd8525 can you do with daytona sir? Never actually seen a video of a bezel assembly/removal of a daytona. There’s none on KZread

Why would the bezel insert need to be lined up precisely when you can rotate it into place anyway?

@mtbbiker6401

Ай бұрын

because rotating bezels are usually 60, 90 or 120 clicks. Even a 120 click bezel may not line up properly so it's important to line up the bezel insert. I suppose if bezels had more clicks (higher resolution) then it wouldn't be as important. Kind of like setting the second hand on an automatic watch. It's not necessary to align the second hand because most automatics tick 6-8 beats per second but extremely important on a quartz that ticks 1 beat per second.

@fcxnom

Ай бұрын

@@mtbbiker6401 interesting thanks!

👋🏻 Is it possible for you to show Rolex Daytona owners how to remove and install the steel 16520/116520or the ceramic 116500ln bezel insert?

@watchmakerjd8525

3 жыл бұрын

If there is a chance to meet Daytona, I will review it. Thanks😊

@leejesslyn5713

3 жыл бұрын

@@watchmakerjd8525 Thank you.

WITHOUTH BEzel.... ITS NEW DATEJUST MODEL LOOOOOOL

Fx

Too risks ..ceramics affraid me sorry ..... i never ask service for a bezel IM NOT A DIVER....LOOL. LAST TIME OMEGA CHANGE IT .... AFTER OTHER IMPORTANT MAINTNANCE WORKS.....

@oralkombat5479

2 жыл бұрын

please return when you have practice your english better. next please...

Bro you're very funny. You have to match the bezel at 12. It's a rotating bezel bro

@nikouai

Жыл бұрын

I guess you haven’t seen misaligned bezels then :)

@Samlol23_drrich

5 ай бұрын

It only clicks into certain spots. Let’s say 1/2 mm each click. So you click it. Now if the little pearl at 12:00 is accidentally not exactly but at the top, and is 1/2 mm to the right, or 1mm, or 1.5mm, you can just move it to the 12:00 position and it will line up fine. But if you accidentally put the pearl 1/4mm to the right, it will never be exactly at 12:00. Always a little right or a little left. Hope that’s clear. I initially agreed with what you wrote 100 percent. Then I realized there were specific clicks in specific spots. If it were clickless and could be infinitely adjusted anywhere you would be right.

Is this a fake Rolex or genuine?

Are those condoms on your fingers?

this is DUMB , put black electrical tape from the base of the blade over the tip the the base of the blade again. Also DO NOT remove the spring , it is a nightmare to get it set back in , you will see he types words over that part and you can see its been edited there. 6:31 , Better yet DONT DO THIS go to a real jewler.