In this video @rpsspain1966 remove the left and right front drive shafts from a Nissan Qashqai 2 6 gear manual transmission. hope you enjoy.
Жүктеу.....
Пікірлер: 21
@luciasmoore2705Ай бұрын
Tidy Job mate, thank you
@rpsspain1966
Ай бұрын
Thank you for your support!
@simonpooley3829 Жыл бұрын
Fantastic video, thank you for your efforts
@rpsspain1966
Жыл бұрын
Thank you Simon, not published anything for a week or so as have been away, more to come this week.
@paulyoung-gb2sy Жыл бұрын
Just changed a front bearing hub on one yesterday...surprisingly easy
@rpsspain1966
Жыл бұрын
it was for this one kzread.infolZEb9T1ygO Engine out at the minute, hopefully get away with bottom end shells, however there was a lot of shiny bits in the oil.
@simonbone
10 ай бұрын
I did the left one last year, which was straightforward apart from some very sticky bolts. This year I did the other side and everything was seized together - the knuckle, backing plate, and bearing. Fortunately, replacement parts not too expensive. Also a good time to replace control arms, drop shafts, and possibly tie rod ends. Fairly simple compared to the rear suspension, at least if you're doing it on the driveway.
@jimbowen501 Жыл бұрын
I have a 2013 petrol qashqai and When a mechanic says the drive shaft is totally fudged does he mean the whole front drive shaft or is it something totally different and is the prop shaft...I had cruching coming from front suspension the last month and got really bad this morning and all i could here was banging and the car was going really slow.
@rpsspain1966
Жыл бұрын
I can not answer for your mechanic, totally fudged is not a diagnosis, he needs to be more specific.
@daveski87 Жыл бұрын
Hi there, how much transmission oil does the gearbox take? Thanks
@rpsspain1966
Жыл бұрын
Manual transmission litres2,0 Transmission type RS6F52A
@ashleyseeley84096 ай бұрын
Do you have to drain the gearbox oil when you changing it?
@rpsspain1966
6 ай бұрын
You will lose oil if you pull the shafts.
@bkfilms5843
Ай бұрын
@@rpsspain1966Yh but how much oil ….
@rpsspain1966
Ай бұрын
@@bkfilms5843 If you drain the oil apprx 2ltrs. you need to check the spec for your vehicle gearbox......Manual transmission, RS6F52A, 6-speed Gear oil (Preferred lubricant specification) Homologation OEM Temperature Viscosity Nissan MT-XZ Manual transmission RS6F52A Gearbox refill 2.0
@MadZprod23 Жыл бұрын
Hiya mate, my qashqai's drive shaft bearing carrier snapped, do you know if you can buy the complete bearing and carrier seprate from the drive shaft or is this going to be a new drive shaft job. Tah
@rpsspain1966
Жыл бұрын
Bearing carrier is a separate part, not sure about the bearing though.
@EvertHarley1 Жыл бұрын
what whas the reason for the removal? i have a (Dutch) J11 too with a ramblin driveshaft on the right side when accelerating and when i drive up (about 1%) my lane it makes a "clongkin" sound could it be that bearing ?
@rpsspain1966
Жыл бұрын
The reason was vibration at speeds over 100 kph.
@rasmadrak8 ай бұрын
Would you say this way is easier than removing the bottom ball joint? This seems easier, although removes more components. I'm "looking forward" to doing both drive shafts on my drive way in a near future, so I'm looking for the quickest and easiest way... 😅
@rpsspain1966
8 ай бұрын
Thank you for watching and taking time to comment. Yes, for me as you do not need to separate the ball joint.
Пікірлер: 21
Tidy Job mate, thank you
@rpsspain1966
Ай бұрын
Thank you for your support!
Fantastic video, thank you for your efforts
@rpsspain1966
Жыл бұрын
Thank you Simon, not published anything for a week or so as have been away, more to come this week.
Just changed a front bearing hub on one yesterday...surprisingly easy
@rpsspain1966
Жыл бұрын
it was for this one kzread.infolZEb9T1ygO Engine out at the minute, hopefully get away with bottom end shells, however there was a lot of shiny bits in the oil.
@simonbone
10 ай бұрын
I did the left one last year, which was straightforward apart from some very sticky bolts. This year I did the other side and everything was seized together - the knuckle, backing plate, and bearing. Fortunately, replacement parts not too expensive. Also a good time to replace control arms, drop shafts, and possibly tie rod ends. Fairly simple compared to the rear suspension, at least if you're doing it on the driveway.
I have a 2013 petrol qashqai and When a mechanic says the drive shaft is totally fudged does he mean the whole front drive shaft or is it something totally different and is the prop shaft...I had cruching coming from front suspension the last month and got really bad this morning and all i could here was banging and the car was going really slow.
@rpsspain1966
Жыл бұрын
I can not answer for your mechanic, totally fudged is not a diagnosis, he needs to be more specific.
Hi there, how much transmission oil does the gearbox take? Thanks
@rpsspain1966
Жыл бұрын
Manual transmission litres2,0 Transmission type RS6F52A
Do you have to drain the gearbox oil when you changing it?
@rpsspain1966
6 ай бұрын
You will lose oil if you pull the shafts.
@bkfilms5843
Ай бұрын
@@rpsspain1966Yh but how much oil ….
@rpsspain1966
Ай бұрын
@@bkfilms5843 If you drain the oil apprx 2ltrs. you need to check the spec for your vehicle gearbox......Manual transmission, RS6F52A, 6-speed Gear oil (Preferred lubricant specification) Homologation OEM Temperature Viscosity Nissan MT-XZ Manual transmission RS6F52A Gearbox refill 2.0
Hiya mate, my qashqai's drive shaft bearing carrier snapped, do you know if you can buy the complete bearing and carrier seprate from the drive shaft or is this going to be a new drive shaft job. Tah
@rpsspain1966
Жыл бұрын
Bearing carrier is a separate part, not sure about the bearing though.
what whas the reason for the removal? i have a (Dutch) J11 too with a ramblin driveshaft on the right side when accelerating and when i drive up (about 1%) my lane it makes a "clongkin" sound could it be that bearing ?
@rpsspain1966
Жыл бұрын
The reason was vibration at speeds over 100 kph.
Would you say this way is easier than removing the bottom ball joint? This seems easier, although removes more components. I'm "looking forward" to doing both drive shafts on my drive way in a near future, so I'm looking for the quickest and easiest way... 😅
@rpsspain1966
8 ай бұрын
Thank you for watching and taking time to comment. Yes, for me as you do not need to separate the ball joint.