Wish I’d found your videos 12 months, good information for a novice. Thanks

Great video. Thanks for doing this. Helps keep the little rippers on track!

@jameswharton3143

3 жыл бұрын

Thanks for the kind words 🙂

Great vid!! New to the KTM 50 world so keep posting. Very instructive!

@jameswharton3143

3 жыл бұрын

Welcome aboard!

Hola,mi 50 ktm sx 2013,la tengo que usar con el ahogador arriba para que funcione mejor,que me recomienda para que funcione sin el,ya que si lo quito pareciera le falte gas

Good video mate 🤙

Just got my son his first KTM 50 SX and your videos are gold sir! Thank you for all the info. Keep them coming

@jameswharton3143

2 жыл бұрын

Thankyou very much you are more than welcome

@apexPRED76

Жыл бұрын

i’m just wondering if there’s any power valves in these 50sx’s… Rebuilt mine (25PSI on last top end) And it’s bogging not wanting to idle and not hitting power band. VforceReeds3 installed. everything is brand new other then the coil pack.

Thanks for the great video!

@jameswharton3143

3 жыл бұрын

Thanks!

Hi I am having issue where my kids ktm 65 revs out after cranking. Ive cleaned carb jets thoroughly made sure intak boots where clamped tight even look at throttle cable but still can’t correct problem. Any suggestions please

What size Jets should I run on my son's 05 ktm Pro 50cc ,currently Tomar Clutch, V force 3 reed,Slip on fmf turbine core 2 slip on,any help would be appreciated Sea level 102' from sea Level, I live in Ocala Florida very humid.

HI, I just purchased a KTM 50 SX 2012, the used bike runs well when warmed up, the previous owner warmed it up well before running, when we started it and began riding with it cold it would have a flat spot in the acceleration until warm. Is this normal? The bike rans perfect after warming up.

Hi mate, IlWe’ve got a 21 tc 50 and it keeps fouling every 2 hours. My young fella doesn’t ride it hard and rev it how it should be. What’s your advice? People are saying a 7 plug instead of 8. Should I look at smaller jets and the needle clip adjustment?

Hello anyone with machanic advice for me. I have a Ktm 50 just put new piston in and had it running sound but the next day theres drag on the back wheel and when I push it fast it starts up with out kickstarting. Im shocked as I know this can happen with geared bikes. Any help and reply welcome. Thanks

Is their a way to drain the carb besides letting the bike run till empty thanks.

Hey mate , would a 95 main cause the bike to splutter every know and then on full noise? 2021 50sx factory edition, cheers

Love these videos

@jameswharton3143

2 жыл бұрын

Thanks for the comment glad you like them!

great vid bud.

@jameswharton3143

3 жыл бұрын

Thanks again for your support

Mate this info worked perfectly on my sons MC50. What are your recommendations for jetting on the MC 65?

Hey mate.. Do you know how to set the float height on these bikes??... Cheers

Is there anywhere you can buy a kit with all different size jets mate?

how do I find what the correct jets are for my location?

Algun consejo de Jets cuando corremos a 3000msnm?

Hi mate what setting do you have your air mixture screw at cheers nick 👍🏻

Hi James, great video! Thankyou! I purchased 5 main jets larger than the stock 95 and 5 smaller jets. My problem is the larger jets don't fit. They don't fit through the wee saucer thing and they don't screw in either. All genuine dellorto parts for the correct year (2021). They are literally 0.0025mm too big to go through the hole in the saucer. I know a squeeze with pliers would force the jet through but I really don't want to do that. Have you come across this before? Thanks in advance

@jameswharton3143

3 жыл бұрын

Hi Dave. Have not had this problem, but have not dealt with a main jet larger than 95. Have a look at the KTM50 Carb blueprints for you bike, www.boltonmotorcycles.com/partFinder/fiche/ktm/2021/50-sx-eu/carburetor#next Here you can see the largest main jet KTM is supplying is a 95. I'm sure dellorto supplies larger but they may not be made for this 19mm carb. What reason are you looking at running above a 95? I have herd of people running larger, but not without other modifications to needle etc

Cheers mate. Top vid. Are your screws still 3 turns and 3 turns?

Hi James, videos are great! Just done the clutch adjustment on my daughters. Bike is struggling to idle when she’s not on the throttle, is there anyway you could help with the setting up of carb screws? Thanks

@jameswharton3143

2 жыл бұрын

Hey Arran. Try adjusting the fuel screw on the carb. The manual calls for 3 turns out but I have had alot more success with it 1 1/2 turns out. See how that goes

James, I have a 2021Husqvarna TC 50 with all stock jetting. The problem I am coming across is that when it sits at the gate after it is warmed up it will load up sitting there waiting for a gate drop unless you constantly clear it out until right before the gate drops. Can you point me in the direction of what you would change in the carb?? Thanks

@jameswharton3143

2 жыл бұрын

Standard issue. Try backing off fuel fuel screw to 1.5 to 2 turns out. Should help

Mate love all of your vids! Great explanation of the whole thing was just wondering what you idle mixture screw is set to? If you could do I vid explaining all about that and your experience with tuning these little rockets 🚀 cheers David

@jameswharton3143

2 жыл бұрын

Thanks for the interest. Try setting your fuel screw to 1.5 turns out, then use the idle screw to set desired idle.

Thank you the videos. Please do a vid on needle too. My son's bike keeps flooding. Cleaned the carbi, no joy. Will try jets next. Regards Shaun

@jameswharton3143

3 жыл бұрын

Will get onto it Shaun. Have a play with your float when you check your jets. Make sure it isn't stuck

@rashellebasore5898

2 жыл бұрын

I need the needle video too same prob as the first comment

Do you have issues with spooge coming out of the exhaust. I have the jetting pretty dialed and I have experimented with different oils and mixture ratios. the bike runs nice and crisp, plug looks good, but I still get a little spooge dripping down the silencer after a day of riding.

@jamesbarnett4946

3 жыл бұрын

Try a lower flashpoint 2 stroke mix

@jameswharton3143

3 жыл бұрын

Hey Bobby sorry I missed this one. 99% of these bikes will still have some splooge leaking from the pipe. If your happy with how its running I would not stress over it

Hi. Great video. Thank you. I'm having a lot of trouble starting my sons sx50, Im pretty sure it's down to carb set up. It seems to flood easily. What jets should I change to to aid starting? Thanks

@jameswharton3143

3 жыл бұрын

Hi sam, is this just an issue cold or also when bike is warm?

@samfowler1956

3 жыл бұрын

@@jameswharton3143 just when it’s cold. Spark plug is wet so fuel is getting through. If I empty the carb bowl it then starts.

@samfowler1956

3 жыл бұрын

I appreciate your help.👍🏻

@jameswharton3143

3 жыл бұрын

Sam alot of guys sometimes have an issue with starting them cold and find tipping the bike up on the front wheel vertically for about 5 to 10 seconds before kicking it over helps alot. If in doubt. Turn fuel off Lie bike on its side, until fuel stops flowing from tubes. Pick bike up and turn fuel back on. Lift bike onto front wheel for 5 to 10 seconds. Kick bike over with choke on. For the record I'm running 48 pilot jet which controls bike at idle.

@samfowler1956

3 жыл бұрын

@@jameswharton3143 yeah I’ve read a lot on forums about them and have tried this but no luck.i will try a new spark plug to see if that helps.

So I should be taking those things out cleaning and putting back in? My sons husky tc 50 starts and revs but bogs out

@jameswharton3143

2 жыл бұрын

Hey for sure it's worth a try, take them out and give them a blow with compressed air

Would you need tomadjust the air screw and fuel mixture screw is you adjust the main jets ?? As I'm having the same issue with my sons sx 50 it's bogging out on full speed and he's loosing alot of ground to other bikes. Iv just bought the same jets you are using to see if this helps. Good videos by the way 👍👍

@jameswharton3143

3 жыл бұрын

Hi Martin thanks for the comment. These bikes have 2 screws that can be adjusted, idle speed which can be turned with fingers and fuel mixture which needs to be adjusted with a flat screwdriver and has a stock setting at 3 turns out. The fuel screw shouldn't effect wide open throttle. Try the 90 main with 48 pilot and air screw and 1.5 turns out, this should also help alot with idle on the grid

@martinb1363

3 жыл бұрын

@@jameswharton3143 Hi James thanks for the reply .. I think I need to adjust the float or atleast make sure it's sitting correctly need to figure that out can't be to hard. But u should have the new jets in a few days at the moment I'm running a 95 main jet and 60 pilot jet.

@jameswharton3143

3 жыл бұрын

How is it idling with a 60 pilot?

@martinb1363

3 жыл бұрын

@@jameswharton3143 idling is fine the only issue I have is top speed im wondering if the clutch is holding him back as he's on 6 turns on the clutch adjustment would that hold him.back on tip end ..? Thanks

@jameswharton3143

3 жыл бұрын

It shouldn't be. Process of elimination, try the 90 main and see if you get any improvement

What’s your idle screw and idle air mixture screw set at?

@jameswharton3143

3 жыл бұрын

Hi James, the screw on the motor side on the carb is the fuel mixture screw. I have that set at 1 and 1/3 turns out. I have found this helps avoid the bike "loading up" at idle. Set you screw to 3 turns out as per factory and have a play to find your sweet spot

Would a 90 main and 48 pilot jet work running 60:1? 2018 50sx,

@jameswharton3143

3 жыл бұрын

Hey Karl that is what I am running on my 2019 50SX. Runs well, maybe a little rich, but I do prefer to be on the rich side. Fuel screw 1.5 turns out (stock is 3 turns out)

@karlkarl6632

3 жыл бұрын

Cheers mate appreciate it

@karlkarl6632

3 жыл бұрын

Do you run the LR8B plug or the CR7 plug?

@jameswharton3143

3 жыл бұрын

At the moment LR8B. From what I am told CR7s will help with fouling. I have a couple in my kit ready to go but yet to test them

@karlkarl6632

3 жыл бұрын

So taken your advice and chased down a 90 n 48, the 90 being much easier to source than the 48. 90 should arrive tomorrow and 48 sometime next week. Will let you know how it goes, also have the Cr7hsa plug to try. Was the lads 1st time on the 50sx from the mini yesterday and got 2hrs from the plug before i had to bin it.

when it's failing only downtown what can it be? at discharge she does not fail. only in downtown

@jameswharton3143

2 жыл бұрын

Hi Alyson, I think you have an issue with it fouling at low revs? If you have already lowered your pilot jet I suggest you wind back the air screw. I have mine set on about 1 1/2 turns out

What does adjusting the needle do

@jameswharton3143

3 жыл бұрын

Hey there, the needle sits inside the main jet and slowly pulls up as the throttle is opened allowing mixture to flow. A higher clip position means a leaner mixture while a lower clip position gives a richer mix

How many turns out is your fuel mixture screw

@jameswharton3143

3 жыл бұрын

Manual calls for 3 turns out, I have mine set to roughly that

Is the bog plate supposed to face that way?

@jameswharton3143

2 жыл бұрын

Hey yes it's supposed to face down

What does that disc on the jet do?

@jameswharton3143

2 жыл бұрын

I believe it stops fuel splashing to the top of the bowl. If it Is installing upside down the bike will bog

Find your videos really helpful any chance you Can do a video on have to sort idle and air mixer screws please

@jameswharton3143

3 жыл бұрын

Hey Adrian I'll look into that. What size pilot are you running? Myself I am running a 48 with the air screw (actually a fuel screw as on LHS of carb) at 1.5 turns out (as opposed to 3 turns out as per manual)

@adriangreen8341

3 жыл бұрын

@@jameswharton3143 hi mate it’s running a 50 and a 90 mate and needle on 2nd down from top

@jameswharton3143

3 жыл бұрын

@@adriangreen8341 try changing the pilot to a 48 and fuel screw (not idle screw) 1 and a half turns out

@adriangreen8341

3 жыл бұрын

@@jameswharton3143 would a bad stator make the bike not idle

@jameswharton3143

3 жыл бұрын

It's worth giving it a test. Make sure your carb is clean, even remove jets and blow them out with some compressed air. How long since you did a top end? These bikes don't idle great. They will always eventually fuel up if you leave them idling for an extended time, especially if the back wheel is stopped on the ground due to the auto clutch bringing down the motor

Why would you change these guys? Generally interested.

@jameswharton3143

3 жыл бұрын

Hey there. The jets control the amount of fuel mixture that flows into the engine. The pilot jet does the first 1/8th throttle and the main jet takes over and does the rest. The bigger the hole (and number) the more fuel flows. The KTM50s are usually jetted a bit rich (too much fuel) so most people drop a size or two

Bure lagche bhai Amar sa script