Wow, a lot of haters. I think that was super useful as someone who hasn't rebuilt a turbo before. Despite the reverse thread explanation hate, I seemed to have understood exactly what he was trying to say. Yes, he used a metal hammer, barely tapped anything, and the world didn't end. Use a rubber mallet if you're worried about it.

@Vacublaster1

3 жыл бұрын

Not hate, this is a video on how to rebuild a turbo using the incorrect tools

@emotionalintelligence776

3 жыл бұрын

@@Vacublaster1 Every mechanic who’s ever worked on any car, has a hammer, get over yourself.

You forgot the most important step. You must make marks so the wheel is on the same exact spot or it will be out of balance and take out the bearings right away. Now you have to send it in for balancing.

Thank for the great video, Every other video I watched they didn't show such an in depth view as yours.

Used your vid to help me take apart my first turbo, watched lots of vids but this was the most encouraging. Just go for it! And yes I used a hammer and it's all fine! Cheers very much great stuff

"Instead of righty tighty, lefty loosey, it's lefty loosey, righty tighty." So. No change there then.

@lurch2846

2 жыл бұрын

Oh, give him a break. I would refer you to the KZread video: "How to stop being anal". Thanks to the fellow who produced this.

@ticohunte8307

2 жыл бұрын

Lol in comment just to see if anyone noticed he said that... but that a mistake lol...

@Simcadepro

Жыл бұрын

@@ticohunte8307 there to many mistakes in this video wouldnt recommend since the shaft isnt balanced. another human seeking attention instead of given proper guides.

Noticed the DP logo that caught my interest while watching your Old video on how to roll fenders about 5 minutes ago. New subscriber from Billings ^^

Your vid is a success bro.. I have followed it and it was hassle free.

you'd think to use a rubber mallet, fuck it I guess

@bendoherty7721

6 жыл бұрын

Bloody scared me. Metal on metal. That’s worst than taking the mother in law and mother and wife all out to dinner

@ozan45

3 жыл бұрын

@@bendoherty7721 what a comparison 😂

Clear and fully understandable.

Awesome, just what i needed. thanks

thanks, its a very good movie for rebuilding the turbocharger

Great job. Thanks a lot.

Entire video.. . .A+

Great vid!👍

righty loosey lefty tighty

@simengundersen8861

7 жыл бұрын

so wrong, just so wrong

@lvr1028

7 жыл бұрын

j gold ak is right since it's reversed thread

@montealexander4390

6 жыл бұрын

Para Jay i

excellent vid thank-you

Neat and tidy, the way to do it!!.

Nice one, thank you very much

yes the manufacture use metric and standard size bolts on this turbo......you all should listen to this person... hes smarter than the engineers who desiged the turbo in the first place by using metric ans standard bolts/ threads

Thx for sharing

Nice video good information 👍

Nice job.

thank you

Good vid

Hmm and they change the whole turbine when its damaged...these things are fixable! Thanks man

did you already loosen up the bolts, or do they just have a low torque setting?

good video and information. But no lubrication on the o rings?

WOWOWO!!! Where is the torque wrench? Guys better use the right torque on the bolts and the nut!!! And if you don't want it to break again soon and complain about a bad rebuild kit just get that thing balanced before installing it. You balance you tires or not? This thing can easy spin 150.000-180.000rpm and if it is not in balance it will break fast! And please check all oil and cooling lines if they are clean! There is always an reason why they break! Like an closed return hose that fails to return the oil and the pressure blows your seal. This is only a half done Turbo repair and will not last long because important things are missing to do it right! And be aware of parts from the compressor wheel that can break and get into the combustion chamber and cause major damage to the engine!!! Please don't do it just like that!!!

Very informative video. However; there was no mention of the torque or replacement pattern? As a high-speed high-temperature mechanism torque break would become imminent. It would be interesting to see a video of what one looked like after it blew up.

Nice vid! How often should you do this? I bought my V50 2.0d at 83K. When it was 63K it had to replace the turbo due to sloppy oil changes. It has now runned 107K (all in KM not miles). So I am thinking about doing this myself.

I have a Evo X td05 and the main circlip keeps popping off did I install something wrong or do I need a new one the kit that I bought didn’t come with a new circlip so I’m using the stock one. Thanks your video was helpful

What made you suspect that you needed a rebuild?Symptoms?

best have long socket bar extension and other side socket in vice .. so no side load to risk bending shaft

Does the rebuild help with shaft play? What about cleaning carbon build up?

wish you would have shown you putting the rings in and attaching the parts

Yoyo Quick turbo question. What do u think would flow better a T4 .63 or a T3 .82 thanks!!!

Will the ball bearings turbo rebuilt process going to be same as this video??

Good video where can i buy the turbo repair kit

"these are reverse threads, so instead of righty tighty- lefty loosey; its lefty loosey-righty tighty".... umm... and those 'C' clip removers are called SNAP RING pliers. LOL

@alexmoreno4114

6 жыл бұрын

Who gives a fuck

@ManifoldSky

5 жыл бұрын

@@alexmoreno4114Um, some watching this video, who therefore might not have the tool, and who therefore has to go out to buy one, and therefore NEEDS TO KNOW THE FUCKING CORRECT NAME. That's who.

@dillonmeier9783

5 жыл бұрын

Go fuck your hat. Everyones a fucking perfectionist

@badninjaa952

5 жыл бұрын

Circlip

@robertlund5694

4 жыл бұрын

@@alexmoreno4114 people trying to buy the tools. Duhh

just a question bro,.. dont you need to balance the shaft or the billets before reassembling? i understand that turbochargers spims up to 240k rpms. doesnt it require balncing so that the billets wont wobble and cause the journal bearing to premature wear? im asking because im also interested to rebuild my turbo and doing a hybrid billet swap. watchung you doing this made it look easy. anyway, thanks for yhe video. just a simple question thats all.

@kingz.a1918

5 жыл бұрын

you should mark the turbine and compressor where they were on the shaft. or need to do the balancing again

didnt see marking alighment for housings or fan to exh side for balance .. did say hed tighten later to see if fits

Great video. How do you find the right rebuild kit for a certain turbo?

@theconsigliere8463

3 жыл бұрын

Know what turbo you have and match it with a parts kit for that particular turbo

How did you aligned cold and hot wheels?

This is the first time I see this machine, can you tell me what it does

I've heard the turbo would need to be sent out to have the compressor wheel rebalanced, etc. Is this true? If not I'll tackle the rebuild this coming weekend lol

What about the important part of rebalancing the turbo, as it is out of balance after using it for years.

@dillonmeier9783

5 жыл бұрын

Factory balanced parts

@johnnygonzalez7874

5 жыл бұрын

How do you balance a turbo ?

@PeterFeltersnatch852

4 жыл бұрын

@@johnnygonzalez7874 You how a fucking gymnast that's how 🤣🤣

@maurizioalfieri602

4 жыл бұрын

If you replace the whole core, it's factory balanced, right? But if you dissasembly the core and repair / replace inner parts, how can you manage balancing then? Isn't necessary?

@barenekid9695

3 ай бұрын

@@maurizioalfieri602 It's Mandatory . THE Trick is to carefully Scribe the Compressor wheel... Shaft... And Nut .. so they can be replaced on the EXACT position they were at from the factory assembly/balancing

Do you know what’s the kit for a 2005 Dodge Ram 3500 diesel 5.9 turbo kit is and were to buy it.

such a shame you didnt have better lighting

Brake cleaner would've been handy to use in that carbon build up and you didn't mark the bolt and shaft for balancing. Tsk, tsk that's a major important factor in taking apart any Turbo for a rebuild.

@dillonmeier9783

5 жыл бұрын

No need to balance

@Surfo1980

5 жыл бұрын

@@dillonmeier9783 Yes you need to Balance... since Balance procedure is for compressor and turbine axial weight differences, so they have to be marked before disambly, so when put together back again, they are in the exact same position they are balanced from factory.

@jamesevertsen1261

3 жыл бұрын

@@Surfo1980 i was wondering about that myself. i had buddy do his own rebuild and turbo would start making bad noises as soon as he made any boost.

It's not always reverse thread. That's a per-turbocharger thing. My TB03 was normal thread.

@f.a3202

Жыл бұрын

same with my T04

It would have been nice to see the play, if any ?, prior to strip down and the use of the hammer scared me, 😂

Did you really do that without balancing the shaft and blades? Also my condolences to the aluminum family, ouch.

@TheBlackManitu

3 жыл бұрын

Right!? I've thought the same.

I have a turbo that I need to rebuild I don’t know how to get the kit it’s a gsp tt2turbo t3 trim 00094

👍👍👍

All "O" rings should be lubricated upon assembly.

shouldn't the core get balanced again?

Greetings, Stephan I'm trying to find a proper direct contact for you? It's in regards to promo opportunities of sorts?

It lefty tightly rightly loosy when backwards threaded

What kind of solvent did you used to clean the whole turbo?

@Peter-wo4uo

Жыл бұрын

Probably brake cleaner.

Hi,please tell me how the turbine should spin , should it be running freely or a bit on the stuff side, thanks

@jesseilton7157

3 жыл бұрын

free, not stiff

Any update on the turbo? How has it fared? Is this worth doing?

@gplusgplus2286

5 жыл бұрын

Probably died after a few months.

so much for the balance of the turbo.. when you didnt mark the shaft against the compressor wheel for its clocking/position you just threw out any of the previous balancing done. That is the comp wheel should been set back in the same rotational position before you undid it.

What about balancing?

how did you clean?

where did you go?

We know them as "Circlip pliers"

Static and dynamic balancing?

Strange to lie about as vital part as mark the wheel pos to shaft. It was quite obvious you didn't as you took it apart and assembled..

My comment is great BUT! You should mark the alignment of the two turbines, they are balanced so need to go back in the same relationship, if you don’t you will effect the balance and at the RPM these spin at balance is critical to life.

Pretty sure there 4 c clips 2 for each bearing. You only should 2. Just wondering.

Surely it's better to replace the core only...

so that turbo has no wastegate actuator..

Those are not c clips those are internal and external snap rings!

What about wheel balancing? Since you removed them they are now out of balance and will cause vibrations

@imGlobL

5 жыл бұрын

The amount of people that have watched this video and have now gone and tried to rebuild their own turbo. Ticking time bombs lol

Can you rebuild any turbo?

any torke in bolts ?

@garywalker3450

5 жыл бұрын

Torque

Remember it's not righty tighty lefty loosey it's lefty loosey righty tighty. Don't forget.

lol, how heavy is that thing? You look a bit stressed there holding it.

@kohlmannn

7 жыл бұрын

They aren't exactly light, which is why people stress the importance of the manifold you use. If you buy a non cast iron manifold you're putting the weight of the turbo completely on the welds in the steel. You also don't want the manifold to hold the turbo very far away because of the leverage you create. Stress on expensive parts = bad. Blown turbo/manifold = bad.

Instead of righty tighty & lefty loosey its gunna be lefty loosey & righty tighty😂😂😂😂

I think you meant Righty loosy and lefty tighty being reversed! ;-)

mfw seel hammer on cast iron ಠ_ಠ

" instead of it being Lefty Loosey righty tighty it's going to be writing tighty lefty Loosey" same thing

You should get a microphone so it doesn’t sound so echoee

What is that sound in the background?

@minorpyro69

7 жыл бұрын

i know right? lol. i thought my house alarm was going off.

@bbldrizzaay

7 жыл бұрын

eimantas28 turbo whistle 😂

@MrCstone1

6 жыл бұрын

The fan he rebuilt last week

@cebrinpitts

6 жыл бұрын

Fluorescent lighting I would think.

sea clips?

Is this the verge video about building a pc...

It's righty loosey lefty tighty facepalm

What happened to him

Forgot to balance the shaft lol

What's a journal bearing ? 😆

you mean righty loosey and lefty tighty !! I don't even think you realized that you said it wrong yo

Its not righty tighty lefty loosy. Its lefty loosy righty tighty.. Ahhh ha ha lmao

You used an 11/16", a 1/2" plus a 13mm wrench and a joiner's hammer with nail remover to hit a cast turbo casing, you're not an engineer are you?

So instead of righty tighty lefty loosey its going to be lefty loosey righty tighty 3:39

Not balanced

oh gosh i want to be a mod guy but im so lost i DO have a hammer tho! I just get yall some cold soda when you need it 😢

is it normal for your compressor wheel to be a bitch to take off i was i got the nut off just fine but the wheel is its self is kickig my ass ! you took yours off like it was nothing

You mean righty Loosey Lefty Thai tea

Aw naw... You did not just hit cast-iron with a steel hammer..

Can the experts in the comments make a how to vid since they know fu#king everything.