How to put highway pegs on a Harley Ultra with Lowers
installing highway pegs on a 2015 Ultra Limited
Жүктеу.....
Пікірлер: 20
@coplock66892 ай бұрын
Damn, I bought that exact bike. same year, color exactly. Cool video.
@recontiger71142 жыл бұрын
Locktite is key! 🎯 Awesome video
@GeRom8312 ай бұрын
I think that I missed the actual “how to” part of this video.
@gavincline209 Жыл бұрын
What pegs are these? Trying to find some that are guaranteed to fit with lowers. And being shorter finding some that will be far back enough to be usable still.
@2ndkickmotoandauto
Жыл бұрын
They were bought on Amazon. Harley sells the same style as well but more expensive
@maxxbenzz7842 Жыл бұрын
Im looking at a 2011 ultra .Do the lowers cook your legs in the summer?
@2ndkickmotoandauto
Жыл бұрын
There is definitely less wind. But they lowers to have vents that open and close. I don't find it bad in the heat. But definitely an advantage in the cold.
@babybugspaw70852 жыл бұрын
Nice pegs,, any idea what torque specs are on those clamps on crash bar?
@2ndkickmotoandauto
Жыл бұрын
I just snug them and if they move easily with my foot on them. I tighten a little bit more. Until movement stops.
@NKBobcat Жыл бұрын
How did you get them to get past the lowers? I have the same pegs ad they won't fit. This video doesn't show you installing them. Misleading.
@2ndkickmotoandauto
Жыл бұрын
Put the outside (facing away from bike part) of the clamp through between the lower and crash bar from the back going towards the front tire where the gap is the widest. Then close clamp and spin it around and move to desired location and install peg bracket and peg to clamp. If you over tighten, you will break the clamp. Fine line between snug and broken with aftermarket pegs.
@NKBobcat
Жыл бұрын
@@2ndkickmotoandauto Thank you!
@majortunesmusic96223 жыл бұрын
Looking for the exhaust pipe bolt dimensions for the switchback turn signal relocation ???
@2ndkickmotoandauto
3 жыл бұрын
Exhaust studs for a twin cam is all you have to ask for. The studs that screw into the head
@majortunesmusic9622
3 жыл бұрын
@@2ndkickmotoandauto sounds good, I’ll give that a shot.
@nathanc1622 Жыл бұрын
How do you get that shim in the peg mount, its so tight
@2ndkickmotoandauto
Жыл бұрын
With patience and strong fingers and a small slot screwdriver to center it
Пікірлер: 20
Damn, I bought that exact bike. same year, color exactly. Cool video.
Locktite is key! 🎯 Awesome video
I think that I missed the actual “how to” part of this video.
What pegs are these? Trying to find some that are guaranteed to fit with lowers. And being shorter finding some that will be far back enough to be usable still.
@2ndkickmotoandauto
Жыл бұрын
They were bought on Amazon. Harley sells the same style as well but more expensive
Im looking at a 2011 ultra .Do the lowers cook your legs in the summer?
@2ndkickmotoandauto
Жыл бұрын
There is definitely less wind. But they lowers to have vents that open and close. I don't find it bad in the heat. But definitely an advantage in the cold.
Nice pegs,, any idea what torque specs are on those clamps on crash bar?
@2ndkickmotoandauto
Жыл бұрын
I just snug them and if they move easily with my foot on them. I tighten a little bit more. Until movement stops.
How did you get them to get past the lowers? I have the same pegs ad they won't fit. This video doesn't show you installing them. Misleading.
@2ndkickmotoandauto
Жыл бұрын
Put the outside (facing away from bike part) of the clamp through between the lower and crash bar from the back going towards the front tire where the gap is the widest. Then close clamp and spin it around and move to desired location and install peg bracket and peg to clamp. If you over tighten, you will break the clamp. Fine line between snug and broken with aftermarket pegs.
@NKBobcat
Жыл бұрын
@@2ndkickmotoandauto Thank you!
Looking for the exhaust pipe bolt dimensions for the switchback turn signal relocation ???
@2ndkickmotoandauto
3 жыл бұрын
Exhaust studs for a twin cam is all you have to ask for. The studs that screw into the head
@majortunesmusic9622
3 жыл бұрын
@@2ndkickmotoandauto sounds good, I’ll give that a shot.
How do you get that shim in the peg mount, its so tight
@2ndkickmotoandauto
Жыл бұрын
With patience and strong fingers and a small slot screwdriver to center it
You lost me at Honda😂
how much did they cost?
@2ndkickmotoandauto
Жыл бұрын
I can't exactly remember. I think 50 or 60 bucks