This short video explains how to purge the regulator hose to help remedy a situation when your grill might not be getting hot enough.
Жүктеу.....
Пікірлер: 80
@delmargolfer Жыл бұрын
Worked for me perfect. Several other KZreads say to uncouple the tank but you are the only one says to leave it settle for a couple minutes. That solved it for me. Thanks
@kidglove1004 жыл бұрын
Thank you this worked on my grill turned it on slow 1/4 of a turn and it lit right up. Funny I unhooked it three times turned the gas on fast and a little gas came out then I found your video and it lit right up.Over the years I've probably threw many good regulators away
@lzmperu4 жыл бұрын
Thanks for the advice. It worked on my RV van LP tank.
@johnszeghy48976 жыл бұрын
Video was exactly what I needed to fix my grill.
@UWPurpleAndGold2 жыл бұрын
So I thought this was just the unplug it and plug it back in trick every IT department tells you to do, but it actually worked twice for me. Especially the part about opening the valve SLOWLY.
@steftheengie29042 жыл бұрын
You sir are a gentleman and a BBQ day saviour. Thank you kindly
@jcksnghst9 ай бұрын
Thank you for this even though my issue was not with a Holland grill. The key is to open the tank valve SLOWLY.
@TwoSwift6513 жыл бұрын
This just worked for me. Thanks!
@CalvinPBerast3 жыл бұрын
at 1:40 you can hear the magic of releasing the pressure. Then I realized it was just wind chimes in the background.
@anthonymonaco98083 жыл бұрын
This was the trick!!! Thank you. I went super slow on the turn on
@shookcs9582 Жыл бұрын
Thank you sir I greatly appreciate it
@EmanTheFreeMan Жыл бұрын
Thank you very much my elder!
@lockettashton43923 жыл бұрын
So easy and it actually worked!! Thanks!
@StevieOneder3 жыл бұрын
Thank you, Sir!
@BlaineCatcheway7 күн бұрын
This worked for me thank you
@coquine19845 жыл бұрын
Thank you soooooo much! You save my BBQ supper! 😉 Simple, clear, effective!!
@Moreno2774
4 жыл бұрын
Damn your hot
@michaelh16216 ай бұрын
Thanks….have a two burner grill and after changing the tank, only one burner would light. After purge, it lit immediately. Thanks again
@sashasabatello89366 жыл бұрын
Good info👍😁👌😎
@victornewman5082 жыл бұрын
Damn, this worked, thank you so much
@gilaguilar8999 Жыл бұрын
Rookie here… thank you for the video, felt I might of had a bad regulator.
@jasonmccord18023 жыл бұрын
Make sure the burner knobs are turned off BEFORE you open the tank valve.
@brentpace10312 жыл бұрын
Most of the time it’s not the regulator. The propane tank was overfilled. Turn the tank on its side and open the bleeder valve for 10 seconds. Works every time.
@jvawelding3 жыл бұрын
Thanks
@danwhite88562 жыл бұрын
Could you put a high pressure valve on it gets more heat
@kmflynn3293 жыл бұрын
I don't trust the on off knobs. I think they might be cheap and leak. So I turn on/off at propane tank. But I have the slow flame. I will try your way.
@chalannbiev314 Жыл бұрын
It work thanks, save my money to buy new regulator
@beepover10 ай бұрын
Worked!
@sandramichaud8033 Жыл бұрын
Thanks.
@badactor34402 жыл бұрын
I wonder if this procedure fixes a pulsating flame
@KarmasSweet3 жыл бұрын
What is that dangling thing when u open the door to expose the propane tank??
@hectoraldana67323 жыл бұрын
Help my Nexgril the grill starts but doesn’t last . Cause the Regulator and Gad line gets frozen ?l
@kunalamin82 жыл бұрын
Is it normal to smell gas when connecting regulator to propane tank ?
@rodt93806 жыл бұрын
I have a problem and maybe you can help. I have a leak as seen on this video >>>: Leaking propane gas regulator on grill (enohcs channel). Per the comments on that video, some claim is the tank that has the problem, but I see the leak coming from the connection/fitting in the brass on the LP Regulator hose assembly... can you give your opinion. Thanks.
@MissTDenton2 жыл бұрын
What if I’m not hearing the hiss before or after connecting the regulator?
@ninoechavez14024 жыл бұрын
Just wanted to ask, does the coupling normally have a rubber seal inside? Thanks
@joshuafoster23
2 жыл бұрын
It depends on brand and model and how precise they machine the pieces. Usually there is one at least. Sometimes veg fiber gasket as well but not always on gas fittings if every one of the components are precision tight.
@michaelfrazier95372 жыл бұрын
So, if it doesn't light after doing this, I need a new regulator, right?
@Uneke6 ай бұрын
Mine keeps freezing up (it’s winter). So I just pour cold water on it lol not hot enough to break it or cause a big change in temp but warm enough to unfreeze it
@doronmerdinger64553 жыл бұрын
After turing on the gas valve , there is gas leak coming out between the connecting head and the actual regulator . (It is an original new gas hose) Any idea what can cause it?
@colbraddock9913
2 жыл бұрын
Yes it's leaking, replace the whole regulator/ hose assembly, no compromise for safety, being cheap now will cost you later.
@jimmywhite8640
2 жыл бұрын
Could also be the o ring on the tank.
@vice80633 жыл бұрын
First time connecting tank to grill and it hissed at me while connecting (tank was off) and I almost sh*t myself and walked away to find this. So that’s normal?
@francisconovoa5894 жыл бұрын
I did that but it didn’t work, then I saw a little hole, I think is a vent on the regulator and the gas leaking through that vent really bad, do I need a new regulator?
@lalitkishore2979
3 жыл бұрын
Yes I have the same problem, did you fix it mate?
@davidcantyne7991Ай бұрын
What is the permanent fix?
@mark1952able3 жыл бұрын
Gas is leaking from regulator regardless of trying what you mentioned. .....must be broken????
@christopherseewald1503 Жыл бұрын
The real life version of Hank Hill
@harpoon_bakery1624 жыл бұрын
is it possible that my AMERI-GAS Propane exchange tanks are all bad...I've gotten 3 brand new regulator and hoses from WEBER GRILL and a exchange propane tank it leaks out the regulator yet again. Im thinking its these damn AMERIGAS exchanges that i get down the street at the MARATHON station. I don't have the silly receipt for it however. I see a black rubber gasket on the propane side that is oblong , oval not round...is that my problem? can i replace it or am i screwed at this point? can i put some 3 in one oil on the black gasket to possibly be able to use this damn cylinder (tank) or should i just take this crap tank back. Or do you think i have a 4th f-ing bad regulator and hose from WEBER?? Sorry for cussing so much and thanks for the video. Anyone else want to chime in, please feel free !!!
@joshuafoster23
2 жыл бұрын
Sounds like a possible user error situation no offense meant. We all repeat mistakes until we know better. I'd recommend the mr heater hoses, specifically the ones that have the rubber that doesn't break down.good luck if you haven't solved yet.
@sasquatch-763410 ай бұрын
I bought a new tank and regulator and did your recommendation twice. Still almost no gas flow at all. Now what.
@khoale18263 жыл бұрын
master made in america ands american. thank you.
@gary94325 жыл бұрын
So basically , don't turn on the gas too hard or it will trip the regulator ?.
@IwCk
5 жыл бұрын
That is correct
@canniggiasweldingfabricati85416 жыл бұрын
Hey mate when an when should it be purged????
@artincorona
5 жыл бұрын
It only needs to be purged when you have tripped the safety regulator and you're not getting enough Flame on your Appliance.
@Msigw4 жыл бұрын
Can't you just close the tank valve, open the burner valve to achieve the same affect?
@StrictlyAwesome
4 жыл бұрын
yes
@hohowan360
4 жыл бұрын
How do you both have the same type of avatars? I don't know for sure but I don't think it's the same because the pressure you're trying to relieve is between the regulator and tank connection.
@lmo11314 жыл бұрын
Did this twice. Disconnected gas, waited 5 minutes, re-connected, SLOWLY opened the valve on the tank... still low flames. You didn't tell us what other situation(s) this could be.
@joshuafoster23
2 жыл бұрын
Yeah, wouldnt that be nice.. i have a few regulators that are slow and couple with no flow. Guess ill keep searching. Ill let you know if i find answers
@gogators5762
2 жыл бұрын
Find solution yet? Please share if so! Thank you kindly
@Samhidesfrombullets
Жыл бұрын
I’ve had the same problem and looked up a bunch of KZread videos that all talk about the same thing. Just buy a new hose and regulator on Amazon for 10 to 20 bucks.
@Uneke
6 ай бұрын
Pour cold water on it It’ll unfreeze it DONT USE HOT. Could crack it
@randallolson8817
20 күн бұрын
Sometime the burner tube holes rust, try cleaning them with a small nail, or oxy/acetylene torch tip cleaner
@Reypure2074 жыл бұрын
Mine still has low flames
@Vfh........y
3 жыл бұрын
Check out the orifice where the gas sprays into the pickup tube inside the grill sometimes a little spider or a little small insect of sorts will build a web in there. Most of the times it is a restriction in the gas line
@ryanfrisby38673 жыл бұрын
Didn't work for me :(
@mark1952able
3 жыл бұрын
Did not work for me either........must be a shot regulator. ....easy fixes don't always work.
@24-Card Жыл бұрын
It does’t work. Done it many times.
@Ccccccccccsssssssssss3 жыл бұрын
Doesn’t work
@mattlawrence87652 жыл бұрын
This did not work
@CimotaTJ4 жыл бұрын
simple tech support people, usually you can fix anything with just unplugging and plugging it back in... no real science
@motube23894 жыл бұрын
Not sure if this guy is trolling or what! But absolutely what he’s done here is just unnecessary and does nothing except having to check again for leaks since it’s a new attempt to make a good seal with the tank 🤦♂️
Пікірлер: 80
Worked for me perfect. Several other KZreads say to uncouple the tank but you are the only one says to leave it settle for a couple minutes. That solved it for me. Thanks
Thank you this worked on my grill turned it on slow 1/4 of a turn and it lit right up. Funny I unhooked it three times turned the gas on fast and a little gas came out then I found your video and it lit right up.Over the years I've probably threw many good regulators away
Thanks for the advice. It worked on my RV van LP tank.
Video was exactly what I needed to fix my grill.
So I thought this was just the unplug it and plug it back in trick every IT department tells you to do, but it actually worked twice for me. Especially the part about opening the valve SLOWLY.
You sir are a gentleman and a BBQ day saviour. Thank you kindly
Thank you for this even though my issue was not with a Holland grill. The key is to open the tank valve SLOWLY.
This just worked for me. Thanks!
at 1:40 you can hear the magic of releasing the pressure. Then I realized it was just wind chimes in the background.
This was the trick!!! Thank you. I went super slow on the turn on
Thank you sir I greatly appreciate it
Thank you very much my elder!
So easy and it actually worked!! Thanks!
Thank you, Sir!
This worked for me thank you
Thank you soooooo much! You save my BBQ supper! 😉 Simple, clear, effective!!
@Moreno2774
4 жыл бұрын
Damn your hot
Thanks….have a two burner grill and after changing the tank, only one burner would light. After purge, it lit immediately. Thanks again
Good info👍😁👌😎
Damn, this worked, thank you so much
Rookie here… thank you for the video, felt I might of had a bad regulator.
Make sure the burner knobs are turned off BEFORE you open the tank valve.
Most of the time it’s not the regulator. The propane tank was overfilled. Turn the tank on its side and open the bleeder valve for 10 seconds. Works every time.
Thanks
Could you put a high pressure valve on it gets more heat
I don't trust the on off knobs. I think they might be cheap and leak. So I turn on/off at propane tank. But I have the slow flame. I will try your way.
It work thanks, save my money to buy new regulator
Worked!
Thanks.
I wonder if this procedure fixes a pulsating flame
What is that dangling thing when u open the door to expose the propane tank??
Help my Nexgril the grill starts but doesn’t last . Cause the Regulator and Gad line gets frozen ?l
Is it normal to smell gas when connecting regulator to propane tank ?
I have a problem and maybe you can help. I have a leak as seen on this video >>>: Leaking propane gas regulator on grill (enohcs channel). Per the comments on that video, some claim is the tank that has the problem, but I see the leak coming from the connection/fitting in the brass on the LP Regulator hose assembly... can you give your opinion. Thanks.
What if I’m not hearing the hiss before or after connecting the regulator?
Just wanted to ask, does the coupling normally have a rubber seal inside? Thanks
@joshuafoster23
2 жыл бұрын
It depends on brand and model and how precise they machine the pieces. Usually there is one at least. Sometimes veg fiber gasket as well but not always on gas fittings if every one of the components are precision tight.
So, if it doesn't light after doing this, I need a new regulator, right?
Mine keeps freezing up (it’s winter). So I just pour cold water on it lol not hot enough to break it or cause a big change in temp but warm enough to unfreeze it
After turing on the gas valve , there is gas leak coming out between the connecting head and the actual regulator . (It is an original new gas hose) Any idea what can cause it?
@colbraddock9913
2 жыл бұрын
Yes it's leaking, replace the whole regulator/ hose assembly, no compromise for safety, being cheap now will cost you later.
@jimmywhite8640
2 жыл бұрын
Could also be the o ring on the tank.
First time connecting tank to grill and it hissed at me while connecting (tank was off) and I almost sh*t myself and walked away to find this. So that’s normal?
I did that but it didn’t work, then I saw a little hole, I think is a vent on the regulator and the gas leaking through that vent really bad, do I need a new regulator?
@lalitkishore2979
3 жыл бұрын
Yes I have the same problem, did you fix it mate?
What is the permanent fix?
Gas is leaking from regulator regardless of trying what you mentioned. .....must be broken????
The real life version of Hank Hill
is it possible that my AMERI-GAS Propane exchange tanks are all bad...I've gotten 3 brand new regulator and hoses from WEBER GRILL and a exchange propane tank it leaks out the regulator yet again. Im thinking its these damn AMERIGAS exchanges that i get down the street at the MARATHON station. I don't have the silly receipt for it however. I see a black rubber gasket on the propane side that is oblong , oval not round...is that my problem? can i replace it or am i screwed at this point? can i put some 3 in one oil on the black gasket to possibly be able to use this damn cylinder (tank) or should i just take this crap tank back. Or do you think i have a 4th f-ing bad regulator and hose from WEBER?? Sorry for cussing so much and thanks for the video. Anyone else want to chime in, please feel free !!!
@joshuafoster23
2 жыл бұрын
Sounds like a possible user error situation no offense meant. We all repeat mistakes until we know better. I'd recommend the mr heater hoses, specifically the ones that have the rubber that doesn't break down.good luck if you haven't solved yet.
I bought a new tank and regulator and did your recommendation twice. Still almost no gas flow at all. Now what.
master made in america ands american. thank you.
So basically , don't turn on the gas too hard or it will trip the regulator ?.
@IwCk
5 жыл бұрын
That is correct
Hey mate when an when should it be purged????
@artincorona
5 жыл бұрын
It only needs to be purged when you have tripped the safety regulator and you're not getting enough Flame on your Appliance.
Can't you just close the tank valve, open the burner valve to achieve the same affect?
@StrictlyAwesome
4 жыл бұрын
yes
@hohowan360
4 жыл бұрын
How do you both have the same type of avatars? I don't know for sure but I don't think it's the same because the pressure you're trying to relieve is between the regulator and tank connection.
Did this twice. Disconnected gas, waited 5 minutes, re-connected, SLOWLY opened the valve on the tank... still low flames. You didn't tell us what other situation(s) this could be.
@joshuafoster23
2 жыл бұрын
Yeah, wouldnt that be nice.. i have a few regulators that are slow and couple with no flow. Guess ill keep searching. Ill let you know if i find answers
@gogators5762
2 жыл бұрын
Find solution yet? Please share if so! Thank you kindly
@Samhidesfrombullets
Жыл бұрын
I’ve had the same problem and looked up a bunch of KZread videos that all talk about the same thing. Just buy a new hose and regulator on Amazon for 10 to 20 bucks.
@Uneke
6 ай бұрын
Pour cold water on it It’ll unfreeze it DONT USE HOT. Could crack it
@randallolson8817
20 күн бұрын
Sometime the burner tube holes rust, try cleaning them with a small nail, or oxy/acetylene torch tip cleaner
Mine still has low flames
@Vfh........y
3 жыл бұрын
Check out the orifice where the gas sprays into the pickup tube inside the grill sometimes a little spider or a little small insect of sorts will build a web in there. Most of the times it is a restriction in the gas line
Didn't work for me :(
@mark1952able
3 жыл бұрын
Did not work for me either........must be a shot regulator. ....easy fixes don't always work.
It does’t work. Done it many times.
Doesn’t work
This did not work
simple tech support people, usually you can fix anything with just unplugging and plugging it back in... no real science
Not sure if this guy is trolling or what! But absolutely what he’s done here is just unnecessary and does nothing except having to check again for leaks since it’s a new attempt to make a good seal with the tank 🤦♂️