its been years i have been looking for this information, thank you so much

感謝！老車真的需要更多的愛來照顧！

Hi. I presume you had resistors in the led wires, what value please? Thanks.

I have been looking for these codes for a long time

Great video... Thankyou!! Did you just make the led tester with just any LED & wires?

@lalim923

Жыл бұрын

Yes, correct

Hi I don’t have TAT pin , how can i diagnostic transmission??

This method works for engine codes, but not for a flashing airbag light. Any idea how to diagnose the airbag fault code?

Great video where do I find the flash codes? What website are you cross referencing the flashes with.

@lalim923

2 жыл бұрын

In the description , I just upload it . Hope its help. www.mediafire.com/file/d9v9zcm55blrsik/Mazda_OBD1_Diagnostic_Code.doc/file

@shanerichards2367

2 жыл бұрын

@@lalim923 yes it worked but mine is throwing out a code of (21 16 ) 2002 Mazda 323. On the list there is no 21 or 16 . Is my car throwing out a 4 digit code?

@lalim923

2 жыл бұрын

4 digit code only can decoded by using handheld scanner , the 2 digit code is correct but for the code 21 not available in the Mazda OBD1 engine code library. Code = Memory = Circuit Diagnosed 02 = Yes = 'NE2' crankshaft position sensor 03 = Yes = 'G' camshaft position sensor 04 = Yes = 'NE1' camshaft/crankshaft position sensor 05 = Yes = Knock sensor 08 = Yes = Volume Air Flow sensor (VAF) 09 = Yes = Coolant temperature sensor (CTS) 10 = Yes = Intake air temperature sensor (IAT) 12 = Yes = Throttle position sensor (TPS) 14 = Yes = Barometric pressure sensor 15 = Yes = LHO2S inactivation error 16 = Yes = Exhaust gas recirculation (EGR) system 17 = Yes = LHO2S inversion error 23 = Yes = RHO2S inactivation error 24 = Yes = RHO2S inversion error 25 = Yes = Fuel pressure regulator control solenoid 26 = No = Canister purge solenoid 28 = No = EGR vacuum solenoid 29 = No = EGR vent solenoid 34 = No = Idle air control (IAC) solenoid 41 = No = VRIS #1 solenoid 46 = No = VRIS #2 solenoid 67 = No = LFAN relay (1993 only) 69 = Yes = ECTF sensor (1993 only)

@dapeco59

Ай бұрын

El link no tiene virus? ​@@lalim923

Way this dont work in my 323f ba, 1,5.95 yr,? I turnir wire in dijagnostic konektor and led, and no signal. Please help mi. Thanks.

what kind of connector does a japanese domestic model mazda 626 capella use?

@lalim923

Жыл бұрын

Mostly Mazda 626 using J850bus+, if not work , try Iso9141-2 K-Line

For US MECS-II which pin is the BUS + line and which other pin is the BUS -ve line?

@lalim923

2 жыл бұрын

Watch this video kzread.info/dash/bejne/dp54lbOpm9u8qps.html

@vincentlee2460

2 жыл бұрын

Thank you so much for sharing this knowledge. I'm going to do this mod so make trouble shooting electronic faults so much easier.

How do u erase error codes stored in the computet after the car is fixed?

@lalim923

2 жыл бұрын

Removes negative terminal of the car battery. Depressed brake for 10 seconds will reset car ecu including error code.

What about airbag (srs) codes? where can i find the flashes meaning for airbag faults?

@lalim923

Жыл бұрын

Hi, In the description have the code for airbag.

@byron1dagg80

Жыл бұрын

@@lalim923 what where in description?

@lalim923

Жыл бұрын

(SRS) Supplemental Restraint System Malfunction codes In order of priority from highest to lowest: - = No air bag lamp: diagnostic monitor (DM), ignition power or bulb circuit - = Continuous lamp: DM disconnected or inoperative 12 = Low battery voltage 13 = Air bag circuit or crash sensor shorted to ground 21 = Safing sensor mounted incorrectly 22 = Safing sensor: output shorted to battery voltage 23 = Safing sensor input feed or return circuit open 24 = Open in circuit 944B or low-resistance in crash sensor(s) 32 = Driver's side air-bag / safing sensor: high resistance or open 33 = Pin 7 not grounded at DM 34 = Driver's side air-bag / safing sensor: low resistance or shorted 35 = Low resistance across pins 8 and 9 of DM 41 = Crash sensor circuit: high resistance or open 44 = RH crash sensor not mounted properly 45 = Center (radiator) crash sensor not mounted properly 46 = LH crash sensor not mounted properly 51 = DM internal fuse: blown and short to ground no longer exists 52 = Backup-power supply: voltage boost fault 53 = Internal DM fault - = Rapid continuous flashing or air-bag lamp: all crash sensors disconnected

@byron1dagg80

Жыл бұрын

@@lalim923 thank you so much i really appreciate your work

@byron1dagg80

Жыл бұрын

@@lalim923 But what terminals do i short and connect led to, to actually read them?

Please how can i get the software to read the codes

@lalim923

Жыл бұрын

In the description has the links.

Saya coba ko led nya gak bisa ngedip ya

You still own and drive the car? Wow.

Hi, my mazda doesn't have a fen terminal on obd port, can you help me to find the way to connect a led to find de error code? Thanks

@lalim923

2 жыл бұрын

Your Mazda 626 car have European (EU MECS-II 1993-2002) Diagnostic Connector, It does not have the FEN pin. Only (US MECS-II 1993-1995) Diagnostic Connector has the FEN pin. You can find the fault code using ELM327 , BUS+ and BUS- is are the communication pins, check out my other video. Mazda OBD1 check engine fault code using ELM327 kzread.info/dash/bejne/dp54lbOpm9u8qps.html

@vincentlee2460

2 жыл бұрын

My Mazda protege year 2000 is US MECS-II. Strange