How to PROGRAM Toyota Remote Fob Yourself / Remote programming for Toyota Corolla, Camry, Sienna etc
Автокөліктер мен көлік құралдары
I show how to program Toyota remote fob yourself. Works for many models of Toyota (See list below). Remote programming for Toyota Corolla or any of these applicable model years is very easy and you do not need the dealership for this. Just follow these steps to program a Toyota remote without a scanner.
Applicable model/years (not exhaustive)
- Corolla 2003 - 2008
- Matrix 2003 - 2008
- Camry 2002 - 2006
- Highlander 2001 - 2007
- 4Runner 2003 - 2009
- Rav4 2003 - 2011
- Sienna 2004 - 2010
- Solara 2004 - 2008
Get from Amazon:
- Aftermarket key fob I used - amzn.to/3ZEYNjs (This fob will work if the FCC ID on the back of your current remote is GQ43VT14T)
- Check out other tools I recommend - amzn.to/42LGCL8
I may earn a small commission from a purchase made through the link above. This does not increase the price you pay in any way.
Programming procedure:
1. With driver door unlocked & open; other doors closed, insert key into ignition and remove twice within 5 seconds.
2. Within 40 seconds, close and open driver door twice, then insert key into ignition and remove the key.
3. Again, within 40 seconds, do these in sequence: close and open driver door twice, insert key into ignition and leave it, close the drivers door, turn the key to the ON position without starting the car (dashboard lights up), turn off the ignition and remove the key
4. The doors should lock and unlock within 3 seconds signalling programming mode is active.
5. Within 40 seconds, press and hold the lock and unlock buttons of the remote you want to add for about 1.5 seconds. Let go of the buttons and immediately press and hold the lock button for 2 seconds. The locks should cycle once within 3 seconds, showing that the programming was successful.
NB: If the locks cycle twice, the key was not accepted. Repeat step 5. To add additional remotes repeat step 5 on the additional remote. Be sure to stay within the 40secs window.
6 Exit programming mode by opening and closing the driver door.
Timestamps
0:00 - Intro
0:25 - Testing new remote fob
0:40 - Remote programming procedure
1:51 - If programming fails
2:11 - Adding more remotes
2:21 - Testing programmed fob
#toyota #keyfob #programming #diymechanic #diycarrepair #diyautoworksng
Пікірлер: 96
Have you used this before? Give a shout 😀Applicable model years are below: - Corolla 2003 - 2008 - Matrix 2003 - 2008 - Camry 2002 - 2006 - Highlander 2001 - 2007 - 4Runner 200 3 - 2009 - Rav4 2003 - 2011 - Sienna 2004 - 2010 - Solara 2004 - 2008 List not exhaustive. _Programming procedure:_ 1. With driver door unlocked & open; other doors closed, insert key into ignition and remove twice within 5 seconds. 2. Within 40 seconds, close and open driver door twice, then insert key into ignition and remove the key. 3. Again, within 40 seconds, do these in sequence: close and open driver door twice, insert key into ignition and leave it, close the drivers door, turn the key to the ON position without starting the car (dashboard lights up), turn off the ignition and remove the key 4. The doors should lock and unlock within 3 seconds signalling programming mode is active. 5. Within 40 seconds, press and hold the lock and unlock buttons of the remote you want to add for about 1.5 seconds. Let go of the buttons and immediately press and hold the lock button for 2 seconds. The locks should cycle once within 3 seconds, showing that the programming was successful. NB: If the locks cycle twice, the key was not accepted. Repeat step 5. To add additional remotes repeat step 5 on the additional remote. Be sure to stay within the 40secs window. 6 Exit programming mode by opening and closing the driver door. Get from Amazon: - Aftermarket key fob I used - amzn.to/3ZEYNjs (This fob will work if the FCC ID on the back of your current remote is GQ43VT14T) I may earn a small commission from a purchase made through the link above. This does not increase the price you pay in any way.
@banquetoflaughter3753
Жыл бұрын
God bless you so much... Full of wisdom!!! Can I join more of you teaching? Any WhatsApp link to learn more???
@DIYAutoworksNG
Жыл бұрын
Hey! Thanks! I don't have a WhatsApp group, but you you can keep close to the content by subscribing if you haven't.
@pescado867
10 ай бұрын
Would this work for a 2009 Toyota Camry?
@axisnetworkinc2577
6 ай бұрын
This procedure didn't work for me. I have 2003 Toyota Ist known on US market as Scion. Please help!
@user-uz5ol3xx8l
5 ай бұрын
How about the Toyota Camry 2015 regular key with a fob not smart key.? Could you please tell us how to program the remote? Thank you.
Thank you for simple explanation, it worked on first try. Toyota Kluger 2012.
@DIYAutoworksNG
11 күн бұрын
Great to know. Thanks for taking the time to leave the feedback. Much appreciated!
Perfect tutorial for my 2004 Toyota Highlander! Saved me so much money by programming myself! Thank you!!
@DIYAutoworksNG
7 ай бұрын
Glad it helped!
Excellent video!!! Sitting in my RAV4 in -2 degree weather in Minnesota trying to figure this out, you saved me from getting frost bite! Thanks my friend!
@DIYAutoworksNG
6 ай бұрын
Glad it helped!
It worked! I followed along with you in the video and it worked perfectly the first time. Thank you so much 😊
@DIYAutoworksNG
6 ай бұрын
Great to hear!
Works perfectly for my 2006 Solara. Thank you.
@DIYAutoworksNG
Ай бұрын
Thanks for the feedback!
Great video! I have a 2015 Toyota Corolla and this worked for both of my fobs. Thank you!
@DIYAutoworksNG
6 ай бұрын
Wow. Didn't know this worked up to the 2015 years.
Excelent video for my camry 2004...
@DIYAutoworksNG
9 ай бұрын
Happy it's helpful. Thanks for watching.
It worked just fine Thank u !! 💯
@DIYAutoworksNG
3 ай бұрын
Excellent. Thanks for sharing!
Nice video my man. This video has stuck on my head for more than ten years that I can do that with my eyes closed and hands tied... But I thought you'd get the fob from me. 😢... But PEACE any-ways!😉
@DIYAutoworksNG
Жыл бұрын
Thanks bro! The story of that fob! Got is some years ago. Lol. Sat unused basically.
I will try it 💕💕💕
@DIYAutoworksNG
Жыл бұрын
All the best! Let me know how it goes.
Thanks God bless Africa 🎉
This is exactly what I need right now after misplacing that of an Highlander
@DIYAutoworksNG
Жыл бұрын
If its a 2001 - 2007 Highlander, you're in luck. If 2008 or later, you'd need a scan tool!
@nnajijohn3577
Жыл бұрын
@@DIYAutoworksNG it's a 2006 Highlander
@DIYAutoworksNG
Жыл бұрын
You're good then 😀
@bobbyomekam8043
Жыл бұрын
@@nnajijohn3577 I have the key and flip type too. Very durable.
Do the procedures work on toyota altis 2002 gen 9.
@DIYAutoworksNG
9 ай бұрын
I think it should if its equipped with key fobs.
06 Camry wasn’t going into programming mode so I bought and installed a new door controller… car goes into programming mode now - the key fob cycles like it’s successful, but then doesn’t lock or unlock anything. Fuse isn’t busted… what else do I do?
@DIYAutoworksNG
9 ай бұрын
Sorry for the belated response. Do you mean the door knob cycles or the key fob?
What if the master key isn't working, what should I do?
@DIYAutoworksNG
Жыл бұрын
Get a new one then.
Hey sir will it work on a 2008 Camry xle push button start?
@DIYAutoworksNG
25 күн бұрын
No. Smart entry cars need scanners to program if I recall correctly.
They’re new ones from Amazon. Thinking batteries are weak from sitting on a shelf for extended periods. Your thoughts?
@DIYAutoworksNG
5 ай бұрын
Totally happens. I've experienced it; weak battery in new key fob.
@brianjames4169
5 ай бұрын
@@DIYAutoworksNG I just installed 2 new batteries and now each one works perfectly. Thanks for your contact. 😊
I have tried this on my 2011 Corolla as the process is the same from my research. I have the right key. I can't get it to program. Either I get the locks cycling informing me it wasn't accepted or nothing happens. I thought maybe it was just a bad battery so I replaced it. I just can't get it to program. What are some reasons the fob won't program? Any suggestions on whst I should do?
@DIYAutoworksNG
Жыл бұрын
From the 2011 corolla, you need a scanner to complete programming
@adamn5821
Жыл бұрын
@@DIYAutoworksNG according to the research I did it doesn't require an obd2 scanner for the remote part of it. I did it exactly the same way in my wifes 2013 with no scanner and it worked on the 1st try. Just that it did incase I tried my Autel and it does even less than if I don't use a scanner.
@DIYAutoworksNG
Жыл бұрын
Hmmm. From programyourremote.com it says a scanner is required.
How do I program the remote start fob for a 2017 Toyota Camry? I am able to program the lock and unlock, but not the remote start.
@DIYAutoworksNG
27 күн бұрын
A scan tool is needed.
Can this procedure work on Honda?
@DIYAutoworksNG
3 ай бұрын
No. Every car manufacturer has a different modality for key fob programming
Good video but I have a problem, the trunk button does not open. There will be some extra programming for that. Thank you very much. I hope for your help.
@DIYAutoworksNG
8 ай бұрын
Thanks. Are using an original toyota key fob or aftermarket?
@finanzasconkevin
3 ай бұрын
I think aftermarket i got mine in amazon and i don't now how to make it work
Please help my 2008 solara keeps locking and unlocking twice and won’t accept the fob
@DIYAutoworksNG
9 ай бұрын
Are you 100% the new fob has the correct FCC ID? Also be sure it's battery is charged.
@xxWileyGamingxx
9 ай бұрын
@@DIYAutoworksNG it’s definitely charged it makes the lock flick 2 times like it’s not accepting it. And I’m not sure about the ID the fob is from my old 2006 Camry I had a couple years ago
I was able to access programming mode, but the remote wouldn't pair. Do I need the original key? And how do I verify which fob to get (I had thr same one you have in the video that was for a 2006 Tundra)? I replaced the battery in the fob just in case.
@DIYAutoworksNG
Ай бұрын
Check the alternative programming procedure for your tundra here www.programyourremote.com/classified/2006-toyota-tundra-keyless-entry-remote-fob-smart-key-programming-instructions-listing-6167.aspx
@DaBaltimoron
Ай бұрын
@DIYAutoworksNG alternate did nothing for me, didn't respond at all
@DIYAutoworksNG
Ай бұрын
I see. And you're doubly sure, you're strictly following the steps in the original procedure, and keeping to the time intervals? If so, not sure what the problem is.
@DaBaltimoron
Ай бұрын
@DIYAutoworksNG I mean, once the car enters programming mode, it's just press both buttons then just press lock, right?
@DIYAutoworksNG
25 күн бұрын
Press and hold lock and unlock for about 1.5 secs, leave all buttons, then press and hold the lock button for 2 seconds. You may need to watch that part of the video over if it's not clear. Hope the battery in the fob is the correct rating and it's good?
It works until I open the trunk and then it stops working. A by attempt to unlock the car doors with the unlock button for the doors only opens the trunk. I don’t get it.
@DIYAutoworksNG
5 ай бұрын
Haven't experience this, but recommend disassembly and cleaning the contact points
Bro.pls help..my Corolla 2010 key fob is no more working..it can't lock d car anymore..it can't do anything again only that i can still use it to start the car by putting the keyfob Infront of the push start button bfr i can start the car...that's how I v been using it...and it will show a cance key sign on the dashboard...I v Change the battery no show
@DIYAutoworksNG
Жыл бұрын
And you used the battery with the right rating? The programming process may need to be redone.
@Healthline1395
Жыл бұрын
@@DIYAutoworksNG I should not lie I havnt buy a high rated battery I only bought those from road side ...pls can u recommend a battery for me thank u bro
@DIYAutoworksNG
Жыл бұрын
Every remote has a battery rated for it, indicated by a number. Common ones are 2025, 2032, 2016, 1616 etc. It may be written on the inside of the fob or in the owners manual. Renata, Sony, Varta, Duracell etc are good brands.
@Healthline1395
Жыл бұрын
@@DIYAutoworksNG thank you bossss
My toyota recently stopped being able to be locked from the key fob i have been trying to re probgram it but nothing will work any ideas
@DIYAutoworksNG
4 ай бұрын
What year of Toyota? Model?
@thebossnes441
4 ай бұрын
@@DIYAutoworksNG 2008 le
@DIYAutoworksNG
4 ай бұрын
What model?
@thebossnes441
4 ай бұрын
@@DIYAutoworksNG luna
@papablessPapabless
3 ай бұрын
Am sure the battery🔋 is dead, make some replacement
How bout for a Toyota Camry 2011
@DIYAutoworksNG
3 ай бұрын
You'll need a scan tool
@lydiaraine9812
3 ай бұрын
@@DIYAutoworksNG any certain kind?
Not working for Corolla 2007.
@DIYAutoworksNG
2 ай бұрын
You followed the instructions to the T?
Bro corolla 94 ae100 program please
@DIYAutoworksNG
Жыл бұрын
A 94 Corolla has no chip. You just cut the key with a locksmith and you're good
@ihsasss
Жыл бұрын
@@DIYAutoworksNG there is keyless entry ecu but it has no green button. The keyless system has been installed
@DIYAutoworksNG
Жыл бұрын
The system must be aftermarket, and will generally depend on the instructions from the manufacturer. Do you know the maker of the system?
Toyota simple key
@DIYAutoworksNG
8 ай бұрын
Yep, relatively simple to program.
My 2009 camry does not go into cycling mode after doing these steps.
@DIYAutoworksNG
9 ай бұрын
The 2009 has a different programming protocol. Only a capable scan tool will program your year.
@trd75sf
9 ай бұрын
Thanks
@glenngentry7523
6 ай бұрын
How about a 2010 Toyota Camry? I do these steps and nothing happens.
@DIYAutoworksNG
6 ай бұрын
Scan tool required for your year. From the pinned comment, you'd see this is only applicable to 2002 - 2006 for Camry's.
@michaelwork5399
2 ай бұрын
I have a 2002 Camry and can’t get it into programming mode