You could weld two pins one per side of the axle & the pin will hold the axle up instead of using a chain.. like a T then the weight of the axle will be on the frame of the trailer..

We run lift Axles in Australia. There very common If that was running empty we would run the front and rear axles up. The way they work here is they fit a 3rd airbag to a cantilever in front of the axle that gets air pressure instead of the 2 main bags that lifts the axle no chain required. And then there’s a over pressure switch to push the center axle down further ( this gives more clearance for the 2 lifted axles )

@averyw.3939

Жыл бұрын

The lift bag is pretty common here in the states too, just not as much on the older trailers. One of our old lowboys had a setup similar to what he built but with pins to hold the axle up. Saves a little bit of weight and complexity, but you had to be on perfectly flat ground for the pins to line up when the trailer was deflated. Our newer trailer has a lift bag (actually it might have two, can't remember now) like you described and it sure saves a lot of time.

I had this on my spread Reefer. Wrapped the chain around the axel and threw the top cross beams (had holes threw beams) I tighten the chain air up rear axel and up she went.

In Brasil is very comum. We use a secondary bag with selenoide for lift from cabin.

@kaiovinicius5573

Жыл бұрын

Haha pelo visto não só tem eu de br nesse canal 😂

@RodrigoFiladelfo

Жыл бұрын

@@kaiovinicius5573 huehue kkkkk

@807mikel

Жыл бұрын

same with michigan 8 axels, we are able to lift 4+ axels from the cab with air to air controlled switches.

@erikthorstensen5185

Жыл бұрын

You can set them up for in cab controls. Alot of trailer dumps have in cab values for lift axles, and tailgate locks. My company has set ups like that on our Mack Pinnacles.

@EO.studios

Жыл бұрын

​@mikel my 10 axle I can lift just about any combination of axles but our 8s is 4 up 4 down

Super excellent quality! Better than watching TV!

I run low bed trailers around the Boston area. My trailer has an air lift rear axle,and a ride height adjustment valve for the front and mid axle. Factory welded on my front axle are chain link locks that are there to hold the front axle up,while the airbag valves are closed on the front. But just with heavy G80 chain I can hold up the mid axle and just ride on the front. If I'm empty, or a light weight machine on it with all my valve set right the mid,and the rear most axles can be 6-8" off the ground. And if I need a second axle down,I just flip the valve for the rear axle. Kinda like a spread axle flat bed trailer. Like I said I'm in the Boston area, our roads can very tight. I comes in handy to pivot on just the front axle.

I really like this! Great job.

Great job man,keeping rolling 👏

Bro been watching for a while! Great energy man you motivate me to stay focused on my goals one day I’ll be in that heavy haul game !! Keep doing what your doing i appreciate the positivity and the knowledge you drop in every video ! I gotta ask too who made that intro beat for yuh bih slide 🔥🔥💪🏾💪🏾

We did it to all axles it makes it nice when changing a tire or if you need to make a really tight turn

19:45 That darn low tree branch Great diy project

Yea that’s a cool idea man. I think actual lifting rear lowboy axles go up a lot higher than that but with most lift axles you can adjust the air pressure… which can adjust the height of the axle off the ground. Or pushing down on the ground raising the vehicle or trailer up. Some just go down and level out with the vehicle and that’s it. Cool idea it’s some work with the binders though

Gotta W9 and you make me wanna record now on my day to day. I do a lot of different stuff with lowboy, walking floor, to flat bed.. might just have to...be safe.

@triple7441

Жыл бұрын

Do it I would subscribe 👋🏽

@jasdeepsingh5163

Жыл бұрын

Yes please

@W96NZ

Жыл бұрын

@@triple7441 gotta few videos up now

@W96NZ

Жыл бұрын

@@jasdeepsingh5163 check it out

Might be worth putting a dump valve on the rear axle when you're running on 6 but need to manoeuver around a tight corner. Been hesitant on installing one on my 55 ton but mostly just because I don't want any extra trouble come winter time. Manoeuvering in small truck stops and OSW detours can get tricky at times.

Excellent! Hand valves!! Why not? We need to get in there more often anyway!

Muy buen trabajo y mucho ahorro de dinero 💲 🤑 💰 saludos desde sudamerica Chile 🇨🇱

Yes sir cool video 🤙

I love it. I been tryin to find a quick way to do mine. Now I have to flip my axle which is a hassle. I need a way to pull the shims and hook chains or something. I love watching your vids man and how resourceful you are.. thx again. Also I can adjust the air in my bags so when the third is lifted I could just add more air to the other two. Your truck sounds like my 5EK.

Ohhhh yeah it’s Friday. New video

You could add air to that 2nd axle get the 3rd up. My excel is a 3 with a flip an I tie up number 4 number 3 has pancake bags on it

Like it.😊

If you drive over some boards with your trailer tires you want lifted it will help you get them up even higher

Which axle is better to have a lift kit installed; the axle close to the back door or the very next axle? Based on a spread axle?

Greatttt video can’t wait to see you tomorrow at the show and record it

@gerardoesparza8650

Жыл бұрын

What show?

@maldonadotruckinghoustontx_

Жыл бұрын

@@gerardoesparza8650 Texas truck market show

@gerardoesparza8650

Жыл бұрын

@@maldonadotruckinghoustontx_ thanks 🙏

@maldonadotruckinghoustontx_

Жыл бұрын

@@gerardoesparza8650 yeah for sure

I am looking at purchasing a tri-axle lowboy trailer and it is missing a set of duals. I am going to see if I can lift that axel and chain it up for the trip home. Thanks for the video.

@Grtruckingdemolitionllc

4 ай бұрын

Good luck!

T800s are nice looking trucks for sure. I dont prefer them bcuz that damn hood is entirely too slanted. I prefer an extended hood, especially since I'm short in height. This way i can see the end of my hood for reference. I dont even prefer the short nose long hoods, bcuz i have to sit up to see the end of the hood. The extended hood is easier bcuz i can still see it even when im sitting low! I dont care about the tight turns etc with the extended hoods, i just make it work, and its fun anyway! Then i love driving them here in Washington DC, in the city, bcuz its very fun!

Have you thought about using the new speed binder?

I’ll be there at the show tomorrow bro

Next time leave the valves open until the axle is up. If the valve is closed you are compressing the bag with air in the line.

See if your boy at the fab shop can put a cross member and some tabs off the axle for pins the no chain needed.

get it cuz

You are charged by how many axles you file on your 2290. If you file for 6 axles it dont matter if you lift 4 of the off the ground you still pay for 6. Its because when you open up an account with the toll way they go by your registration. Now that ONLY applies to people who have a toll transponder. But if you are stopping and paying your tolls at every booth. Then that dont apply to you. Even then your spending more money by not having a transponder

@Grtruckingdemolitionllc

Жыл бұрын

Here in houston/Texas they have sensor on the ground that count the axles. I don’t get charged for it when it’s up. I have been checking my account and it does work

Hey big dog was wondering if you could make able to video about getting permits for being oversized/over weight.

Have fun and don't forget the video

Maybe you should inform some rookies to release the air pressure just in case, maybe.

Lol you gave me a headache when you knocked us off with the tree

Mine has a chain on each side of the axle with brackets on the side. Then you just move the chain so it will either lift or operate normal. I can send you pictures if you are interested

@olivierdube9121

Жыл бұрын

That's the best way to do it, not have to go under anything

@biggdre337

Ай бұрын

Where can I see this?

Make sure that axle is 5 or 6 inches off the ground. You wouldn't want the rear axle hitting the road every time you cross an overpass or bridge. I saw a box truck with a tag axle on the rear and every serious bump he crossed the rear axle hit the asphalt and puffs of blue smoke would appear Maybe you could use a De tent pin to reset your ride height plunger for 2 or 3 axle use

Why are u changing the axles for ??

Tree branch got the camera luckily it still recorded and you seen it fall

I won't to come but I got to work

What about the abs ?

Why do tolls charge for axles? Is it because they factor it for road maintenance?

@Grtruckingdemolitionllc

Жыл бұрын

Yes sie, and also the city gets some money from that

lol how he find his damn cam

So, im assuming that you will only be using this makeshift lift axle while empty? Bcuz im assuming that since the axle is not lifted to its normal height, that soons you put at least a certain amount of weight on the trailer, that the axle, although slightly lifted, will still touch the ground, right? Thats why i say you must plan to use it while empty. I haven't finished the video yet, so maybe you will show this!

@Grtruckingdemolitionllc

8 ай бұрын

Yes the rear axle I actually don’t lift it up at all, but I did the same thing to the front axle and have that one up most of the time empty or loaded.

I guess the dozer wasnt heavy enough, and didnt load dar back enough to make that makeshift lift axle touch the ground. Even then, if something is that heavy and loads to the back on the hump, it would be wise to use that axle anyway! Im not gonna lie, i would get irritated with cranking that axle every damn day, more than once a day, unless it was somehow above the trailer or maybe on the rear somewhere, where i aint gotta squeeze my arm in that hole, or continuously climb under the trailer to crank the axle!

Do you know anyone that does axle lift in Houston? need it done to my flatbed.

@erikthorstensen5185

Жыл бұрын

Check around,aftermarket truck outfitters that supply dump bodies ,ect might have what you need.

Why don't you put 1 chain on each side of the trailer with a binder in the middle on top ? A 5' wrapped around the axle between the inside rim and trailer frame on each side, going up on the trailer with a binder joining the 2 ? This way you don't crawl under the trailer ever

If you want to see what my area is like to drive in check out a friend of mine on KZread. The Boston Trucker. Mike is a good man.

That's good you got your lowboy axles to raise. You'll definitely be able to save and maneuver better in tighter areas. I've seen end dump trailers, flatbed trailers, box trailers, and tank trailers have lift axles and most if not all of those trailers only had 2 axles. Just curious is this something you think you'd ever do to the end dump trailer?

@erikthorstensen5185

Жыл бұрын

Most of those lifted axles actually have a lift airbag. By flipping one valve switch will supply air to the lift bag,and vent the suspension bags. Kinda like lift axles on a tri axle dump truck.

Wouldn’t it be cheaper to get a tx toll tag

@Grtruckingdemolitionllc

11 ай бұрын

Same thing you pay the toll for that axle

You think I could make good money staying local in Texas doing heavy haul?

@Grtruckingdemolitionllc

Жыл бұрын

The money on heavy haul is out of town bro local is not well payed

@SkeemieTV

Жыл бұрын

@@Grtruckingdemolitionllc yeah I think I’m going to run it otr. Thanks for replying

@cesar9496

8 ай бұрын

@@SkeemieTVget you a good construction company that’s busy and you’ll make very good money. I’m local with just 1 company and damn, not bad at all. Grossing 230k a year here in Houston.

@SkeemieTV

8 ай бұрын

@@cesar9496 I’m about to get one truck and just run Texas and see how it goes.

@cesar9496

8 ай бұрын

@@SkeemieTV you’ll be good. A shit load of construction work here in Texas. Sun shines for everybody, come on!

Esta buena la mexicanada es mucho pedo

God Bless in Jesus Christ Name Amen.