How To Make Powerful (100 Watt) Amplifier Circuit || DC 12v
Тәжірибелік нұсқаулар және стиль
In this video, we are going to show you making a Powerful amplifier circuit using only two transistor. It is a super loud amplifier circuit. You also try to make this amplifier at home easily. Using Only DC 12v you can operate this amplifier circuit easily. you also can use inside your car, bike, truck, etc.
To make this circuit, you might need some electronics component. Those component list have to been given below.
Component List :
1. Transistor - Tip 122
Tip 127
2. Volume - B 100 K
3. Capacitor - 470uf / 25v
4. Resistor - 150 k ohm
5. Speaker - 100 watt
6. Power Source - DC 12v
7. Heat Sink
8. Connection Wire
#Power_Amplifier
#100watt_Amplifier
#DC12v_Amplifier
Пікірлер: 1 100
Must of you guys here just criticize negatively. I would like to see if some of those dudes who are negative construct and explain something better. This guy is doing something for those who are beginners such as high school students where people that don't have any knowledge of circuit theory and how to polarize a transistor. Those carpers should share and at least to advise and how to improve this. it also misses and preamplifier and active filters to avoid saturation on low frequencies. The concept is perfect and simple. It is a power out stage.
@CreativeWorldPro
3 жыл бұрын
thanks
@critique1970
2 ай бұрын
I totally agree. We should encourage beginners
Legal porque ele da detalhes de cada componente , valeu!
Muy bueno, simple y efectivo
This thing WORKED... Prior I thought it is trash but when I made it it worked 100 percent... THANKS DUDE
@CreativeWorldPro
4 жыл бұрын
congratulation, 😘
Está bueno al escucharlo ringtones,cuando lo separeste de la mesa la bocina se a claro.angel de nicaragua
Super. Ovoru sparelayum price pota Innum nallairukum. I THANK YOU
The explanation about the conductors and capcititors and how to connect is to be explained while doing is more effective and useful
@romanromi4540
4 жыл бұрын
😁🅰🅰😁😁😁😁😁 🅰😁😁🅰😁😁🅰😁 🅰🅰🅰🅰😁🅰🅰🅰 🅰😁😁🅰😁😁🅰😁 🅰😁😁🅰😁😁😁4 Wo
Nice n easy amp ... Can work truly...? Very good... I try later if work then ..I make stereo amp ... Thanks 👍😀😀😀
@geerreeshb7766
4 жыл бұрын
12v ok 1 amp or 2 am
The world would be so wonderful place, if this amplifier had 100W... :-)
@sergeyflayer
4 жыл бұрын
Angry Student , ага! 100W он из 12 Вольт решил добыть, да еще на двух транзисторах!Сказочник)))) Такое возможно только в России!))))
@haseebawan8326
3 жыл бұрын
Loved your comnt angry student
@khaledhassan701
2 жыл бұрын
Speaker is 8 oum or what
I like that you wrote exactly what you were doing it was very helpful most of these videos they do it so fast and looks like they skip steps thanks
@CreativeWorldPro
4 жыл бұрын
thanks a lot,,,
the best video so far easy to get parts and build unlike some other videos using parts that isn't available at jaycar electronics and altronics in western Australia, Australia except the tip27 dam it and after reading the comments this circuit has errors maybe its using the wrong speaker maybe it needs an 8 ohms one
felisidades quedo muy bueno ya lo hice y esta muy bueno
MUY BIEN
Saman uchkane ki mashin👌👌👌👌👌
Gostei do amplificador é muito bom ok professor, Fais um amplificador com 2 transistos tipo 127 ok
That bass sounds AWESOME! I'm gonna put this in my car and cruise the neighborhood!
This would be a 20W sound amplifier if there were no heat losses in the transistors. Considering this is a Sziklai (compound) pair of two Darlington IC's, I think it falls under the AB class amplifier. AB have around 75% efficiency, so one quarter of the total absorbed power would be pure heat. One quarter of 20 is 5, so 5W (or more) are dissipated into that heatsink as heat. A 15W amplifier with two Darlington transistors is still okay, mind you. Great job!
@mohaabdo8146
2 жыл бұрын
👍✅ Your analysis is very good
@EricFontaineJazz
2 жыл бұрын
Where does your starting 20 W number come from?
@marahutay
Жыл бұрын
@@EricFontaineJazz assuming his understanding and assessment of the parts is correct, he gets 20w after subtracting the theoretical thermal energy wasted from traveling thru the circuit.
500K resistor VS 50V DC 😮 power supply to speaker booster 500W 2x 13003 transistor amplifier 😅 power high 😂😂❤
Muy buen video.Lo intentar'e.Bendiciones.Muchas gracias.Horacio.Cali.Colombia.
@CreativeWorldPro
Жыл бұрын
thanks a lot
Сел бы на динамик может тоже подбросило вверх) а вообще красава! 👍
Typically, when one demonstrates how well an amplifier circuit works one builds, they demonstrate how good it sounds. This circuit simply demonstrated that it could drive a speaker's voice coil windings enough to make the cone of the speaker vibrate & bounce assorted objects around. I believe some sound was emitted from the speaker however, it was distorted beyond the point of recognizing if it was music or perhaps grunting noises made by certain animals in the wild.
@X7cF4
Жыл бұрын
but the heavy sound is what makes it fun
3:57 - OMG jaki prąd spoczynkowy, połowa napięcia zasilania :D ja bałbym się podłączyć to coś do smartfona. 3W to wszystko co można na tym wyciągnąć z kondensatorem wyjściowym 4700uF.
@olgamorales5957
4 жыл бұрын
Si
Very good and useful video, I'm a loyal fan waiting for the next video, always successful
@CreativeWorldPro
4 жыл бұрын
Glad to hear that,,,, thanks a lot
Bahut badiya bhai,
As an experiment is fine, I would have to put filters to see how much it really performs, possible 8w, for that I would better use a TDA2003 that if it would give a better sound
of course I will try to do it I will hope that it will work
@CreativeWorldPro
3 жыл бұрын
sure
Молодец продолжай так же! Лайк
The fly seems to like your music, then, it has to be a good project !!
muy bueno el circuito del amplificador pero no se vio como se alimenta de voltaje
Your explanation is excellent, simplified, and very nice. Keep it up, Bechmhands engineer. We support you. Can I have a simple request? I have a 4 ohm headphone, 100 to 600 wat, 5 volt.What amplifiers and resistance value do I need?
What people will do for a Viral Video. But hey, nice attempt on the amp 🌴💀👍
Como vibrador está bacan...!
Muito bom! Fantastico!
@CreativeWorldPro
3 жыл бұрын
thanks a lot
THD100% ;D
@SteelBlueVision
4 жыл бұрын
Wasn't meant for audio, it's an object shaker, as demonstrated.
Muy bueno para aprender
1minutes nice working Heavy Heat Sound problem
Hello friend, greetings from the United Mexican States, I wanted to ask you if you connected it to any source of power, I wanted to know or tell me clearly, that in your video it does not look like you connect it, I did not understand well, your video is good
What a brilliant design. Using darlington pair with current gain of 1000. Feeding the circuit with a 0.1Watt music source, x1000 times, you get a ball-park of 120 watts. What you get is, with 12 volt supply, the high gain of a small sine wave got magnified and clamped at 12 volt and became a square wave, makes it sound shitty. The output of the circuit has a AC and a DC component. You are effectively making a degauss circuit for demagnetizing your speaker.
Wowww great job
nice idea dear friend
@CreativeWorldPro
Жыл бұрын
thanks
great amplifier circuit
12V applied across a speaker CAN NOT dissipate 100W of energy. 12V across a 4ohm speaker will dissipate 36W, 12V across a 8ohm speaker will dissipate 18W.
@EricFontaineJazz
2 жыл бұрын
The video title is very misleading because speaker impedance tends to not be less than 4 ohm. But the equation Power = (Voltage ^ 2) / Impedance does have a solution for 100 W peak power across 12 V if the impedance is 1.44 ohms. I just did a web search and see there are car speakers that are 2 ohm (which according to the equation could dissipate 72 W peak power with 12 V) and even 1 ohm (which according to the equation could dissipate 144 W peak power with 12 V). Of course that is peak power (not RMS) and isn't accounting for other issues, such as the limitation (according to the datasheet for the TIP 122 and TIP 127) that the absolute max rating for these transistor's collector current is 5 A and a peak of 8 A.
@EricFontaineJazz
2 жыл бұрын
and there are other power losses such as in the transistors, and some one in the comments below is saying that since this is a class AB amp, it can only have 75% efficiency too.
Awesome sound quality....! Yes,of course!
@CreativeWorldPro
3 жыл бұрын
Glad to hear that!
Boht powerful board bnaya tha orr bhi components the usme Apne 3 ic ka use kia tha orr capistor bhi brda use kia tha 1000 + uf tha usmai
Все красиво, кроме звучания!
@user-yj8qm3mp9d
4 жыл бұрын
звучание и должно фонить
@user-eq2rx4xj6l
4 жыл бұрын
а как он должен звучать если это низкочастотник и вдобавок без короба
@Alex-em7zt
4 жыл бұрын
Затея не плохая, но мне кажется проще купить уж на полкиловата
@user-gx7mc8sg6p
4 жыл бұрын
Динамик открыт, отсюда такое звук. А подключить колонку, будет супер-звук.
@radiotektv
4 жыл бұрын
@@user-gx7mc8sg6p не уверен, питание слабое,нужно минемум для 100 вт хотяб 32вольта
Se ve y oye que sumba excelente
Nice
EXCELENTE VIDEO, me funcionó muy bien con un TIP31C y un TIP32c
Действительно 12Вт. Из википедии. Но простота усилка удивляет...
@dkromanovich
4 жыл бұрын
Кидалово удивляет
The only thing missing is the Flux Capacitor to really get those Bass vibes.
@kevinhoward8410
4 жыл бұрын
Flux capacitors are only suitable for high frequencies--no good for bass.
THANK YOU SO MUCH
@CreativeWorldPro
2 жыл бұрын
Glad it helped
Good job 👍
Is that plumbing solder paste you are applying to the joints before soldering? It's not an amplifier, it's a noise maker ......
what speaker resistances can you use this amplifier at? and what is the max voltage you can put into this cct?
I like this bass
I will try it now.
Not a recommended amplifier design when the cone of your speaker pips out when power is applied. That means it's getting DC voltage and potentially burning the voice coil.
@HeLrAiSiNg1
3 жыл бұрын
Its already burned i can fell the distortion
@ernestgodspower6813
2 жыл бұрын
Then what 12v dc amplifier would you recommend I really need it
Отличная взбивалка яиц
@user-bo9ce4mg8l
4 жыл бұрын
При чем яиц того, кто это паял и выложил сюда!
Nice baby rattle, by the way.
Olá meu caro, tem como fazer um amplificador de 5000 w
You are seriously connecting a +12v input directly into a speaker? Notice as soon as you applied power, the cone popped straight out? That should have been your 1st hint that it is a bad circuit. Any 1st year electronics student can tell you that speakers are AC output devices. You don't plug DC directly into them. That's what burns out voice coils. Audio amplifiers take an AC Signal input and, converts it to a stronger AC output signal. DC is used to power the amplifier. Not amplify an audio signal. Audio is an AC, Amplitude modulated signal. Distortion is caused by an over modulated audio signal injecting square wave DC into the audio. That's what fries voice coils. If anything, you have created a voltage amplifier. NOT an audio amplifier. Also, 100 watts. Not with that circuit. My advice to you is go back to a 1st year electronic course book and learn how to design a proper circuit before some beginner uses your video and then blows an expensive set of speakers or, worse yet, causes a fire. What you have shown here is a potential for, at best, lost money. At worse? you could kill somebody in a fire. Shame on you.
@valcye
4 жыл бұрын
Nah! first things 1) cutting finger nails 2) wash hands
@ronalddaub5049
4 жыл бұрын
But that's not the way this particular circuit works
@nanami5814
4 жыл бұрын
I test the circuit on LTspice, and it works. But it is a class C amp, only half wave above 0V got amplify, and signal below 0V is all flat, kind shiity in audio application .
@vincentrobinette1507
4 жыл бұрын
The speaker sees 6 volts with zero signal. This is a class "A" amplifier, the 2 transistors are connected in a "Darlington" circuit, with the TIP 122 serving as the input stage, The TIP 127 is the output stage. The problem is, the speaker coil dissipates 9 watts, if it's a 4Ω speaker, 4.5 watts, if it's 8Ω.(no signal)
@user-vx3fr4kh4b
4 жыл бұрын
垃圾视频!
Nice video bro
@CreativeWorldPro
4 жыл бұрын
thanks a lot
It would be more interesting if you could provide a full explanation of this scheme.
Eu tenho uma fonte de 18 volts, tem algum problema usá-lo neste amplificador?
oh my God where the power supply? your'e just dreaming...
great work brother
@CreativeWorldPro
3 жыл бұрын
Thanks ✌️
Mantab.
"How to to make a very poor highly distorted amplifier"
@DavidJyt
3 жыл бұрын
Nah it sounds like the speaker is badly blown and damaged
SERIA BUENO CREAR UN DIAGRAMA PARA SER MAS CLARO
ayos galing mo boss
Thank you for the great amplifier. Thank you.
@CreativeWorldPro
3 жыл бұрын
Our pleasure!
Oh look the screw driver to oh look the speaker lead and if you missed it oh look the same speaker lead following up putting junk on the already distorted speaker.
@kapiljatav9083
3 жыл бұрын
@SPEAKER GUY hii
The Internet: The home of poor designs.
Muy interesante
Хороша перделка получилась))
Только я что-ли заметил, что винты поставил без изоляции, тем самым соединил оба коллектора
@ekhwelwe
4 жыл бұрын
Пересмотрев видео, обратите внимание что на сами винты уже одета изоляция
@user-gx7mc8sg6p
4 жыл бұрын
Нет, винты на изоляторах, смотри внимательно. То что 2 винта на коллекторе, ничего не значит, они не прикасаются к транзисторам!
@makcimenuka7904
4 жыл бұрын
Видно глаза нарисованы на голове))
@makcimenuka7904
4 жыл бұрын
Кепку сними блядь.
Why does the speaker have 2 red wires but the amp has a black and red wire
@Hammerjockeyrepair
4 жыл бұрын
@@bryang9601 thats the real amp, sounds like trash just like the plans would. The red speaker wire is going along with the black dc- wire to the ground at power supply most likely
@kevinhoward8410
4 жыл бұрын
Don't criticize him for his wire colors--criticize him for showing a project that's completely useless at best, and very likely a waste of time, a speaker and perfectly good components.
@raylularoussef247dasilva6
4 жыл бұрын
Because red wires can handle more power and black wires are only for small signals ( don't you know the "Colors Law for Applied Electronics" It is the most important law in modern physics . hahahahahahahaha
Nice performance
Me gustan esos proyectos
OH GREAT YOU MADE A MINI TRAMPOLINE
With a voltage of 12v it is impossible to get 100e over 4 ohm. Don't you know Ohm's law? Well, before giving electronic lessons, you should know it since it is the basic law of electricity.
@Robio1971
4 жыл бұрын
With that simple configuration I would agree 100watts is not realistic however if the 12volt source has allot of current like a car battery it is obtainable.
4 жыл бұрын
That’s true, he could be using a computer or Xbox power supply for more current to power 100 watt at 4 ohm.
@matthewstorm5188
4 жыл бұрын
@Robio Weeks 100W is perfectly attainable from a 12V source (like a car battery). But not to a 4 ohm load. At a maximum (which would be pure DC), you could get 36W from 12V into a 4 ohm load. The minute you start to generate waveforms (which will lower the RMS voltage from pure DC), this figure decreases further. Put in another way, in order to get 100W into 4 ohms with a pure DC voltage, you need 20V. Make that a sine wave, and you now need a voltage source with an amplitude of 28.2V. Oh, and that’s into a pure resistive load.
@stevekolhoff9240
4 жыл бұрын
No, it is not. UNLESS. you put the +12VDC through a DC-DC switching power supply which boosts the +12VDC to at least +/-40-45VDC. Only then can you get 100W into 8Ω. 200W into 4Ω. Not trying to kill the creativity here, just want to point out the reality.
@LittleFlockDisciples
4 жыл бұрын
Guess that explains why I here is different amps with varying quality got four or five different "pros" telling us how to get it done right Lol Guessing this is the low end scale of the quality
Super super super super super fantastic
@CreativeWorldPro
2 жыл бұрын
Thank you so much
Good work, I impressed.
@CreativeWorldPro
4 жыл бұрын
thanks
we need one that does not output DC for Speaker Because Speakers hate DC and it ruins the Voice Coil in Them
@djob3507
4 жыл бұрын
Yup
@TheZombieSlayer1155
4 жыл бұрын
Yeah, putting any form of dc power can fuck up you're speajee. But if he want untangled and burnt coils nkt my problem hehe
Thank you. I just have 2 questions. What Ohm speaker can it take and what Amp max 12v power supply can be used?
@ANGEL-mb9yx
4 жыл бұрын
please use a fuse if you are using high Ah battery
hello thank you bro
@CreativeWorldPro
3 жыл бұрын
Welcome 👍
good idea
why are you putting things on the speaker then the speaker will distort ,we are here for the sound quality!
@Elcosmicstar1
3 жыл бұрын
Because he wants to hide the extremely high distortion.
It is 50w-50w amplifier
It is so. Power ful
Thanks for share
@CreativeWorldPro
3 жыл бұрын
My pleasure
We can all bitch about everything wrong in this video but the fact is that this guy is showing us just the principle of a little circuit. Eventhough his standards for "Awesome sound quality" is a bit off.
Very low quality distorted sounds
@betabilly
4 жыл бұрын
Yeah, that's the beauty of DC output; essentially clipping half the signal's wave form.
@jmbrowning6688
4 жыл бұрын
should be ok for rap music then............. :P
@robertjordan3572
4 жыл бұрын
Perfect for the rock & roll genre
@agberteyprinnce47
4 жыл бұрын
Shinu Varghese
@mariaquirozvega1417
4 жыл бұрын
It's sounds really baaad
It doesn't matter if he's lying or not. This is KZread. You can say any shit and show any shit and people will watch and you can make money. And there's nothing anyone can do about it because KZread is making money off of it too and they don't give a shit if it's true or not. So enjoy everyone and send them your money.
It sounds just fine for what it is. Its a bass speaker that is not in proper box, putting out bass only as there is no mid range or highs so you hear no voice. In the right speaker box with a high speaker to create some voice the bass would sound fine.
Power on--dc offset very high--speaker membrane jump out---missing the output capacitor,for brake the DC offset,this circuit class a for speaker coil heater technology.....
Alguien que le diga a este puñetas que se oye bien gacho su amplificador de cien watts.
@abrahamzavaleta6838
4 жыл бұрын
Si
👍👍👍 mantaaaaf...😍😍😍😍
Muy bueno
Primero que no se deben colocar objetos y mucho menos tan pesados sobre el cono del altavoz y segundo que sera muy simple el circuito pero así suena malísimo. . . . . .