How To Make Motion Sensor Light Switch using CD4017 & IR sensor at Home
In this 4017 project, I have shown how to make motion sensor light switch using CD4017 & IR sensor for the washroom. I have made the complete motion sensor circuit on a homemade PCB and use this circuit as the automatic washroom light switch. When anyone enters the washroom the IR sensor senses the motion and turns on the light and when he or she exit from the washroom the IR proximity sensor again senses the motion and accordingly turns off the light automatically.
During the tutorial video, I have shared the complete 4017 ic project circuit diagram, so after watching the video, you can easily make this simple motion sensor project using 4017 IC and use it as motion-activated light or motion-activated alarm.
To Download PCB Layout for the CD417 projects please visit the following article
easyelectronic...
Required components for the CD4017 project
1) CD4017 IC
2) LM358 IC
3) BC547 Transistor
4) 100uF 25V Capacitor
5) 1000uF 25V Capacitor
6) 220-ohm 0.25watt Resistors - 4 no
7) 10k 0.25watt Resistor
8) 10k Trimmer
9) LED 5mm - 2no
10) IR LED pair (Detector & Emitter)
11) 1N4007 Diode
12) 5V SPDT Relay
13) Connectors & IC Base
14) Acrylic sheet
I have used the 5V mobile charger to supply the circuit. Please take proper safety precautions while working on 110V or 230V AC.
You can also adjust the sensitivity of the motion sensor using the 10k trimmer.
After watching the video, you can easily design this motion sensitive light switch circuit for your home.
If you face any issues please let me know in the comment section.
#motionsensor #4017ic
------------------------------------------------------
Thanks For Watching...
✅ SUBSCRIBE ✅LIKE ✅SHARE ✅ COMMENTS
Website: easyelectronic...
Facebook: / techstudycell
Instagram: / techstudycell
Telegram: t.me/techstudy...
-------------------------------------------------------
Other useful videos:
How To Make Motion Sensor Light switch on the breadboard
• How To Make Motion Sen...
IR Remote Control ON OFF Switch using 4017 IC & Relay
• How to make wireless I...
How to calculate resistor value for LEDs in a circuit for 9V and 12V
• How to select resistor...
How to make Remote Control Switch on the breadboard
• How to make Remote Con...
Пікірлер: 812
To increase the range, Pls refer to the new video on Motion Sensor Switch: kzread.info/dash/bejne/lZOY0KdvgrWzc6Q.html
@deshanpraboda9844
Жыл бұрын
What device can be bought instead of the 10k trimmer ? It is not available in the market to buy 10k trimmer device ?
@its_rahul7519
9 ай бұрын
Hello sir mujhe thodi help chahiye
@its_rahul7519
9 ай бұрын
Ye circuit meine banaya hai pr sirf light off ho Rahi hai on nhi ho Rahi hai
@Esha648
9 ай бұрын
@@its_rahul7519 ap ny project banaya ha mujhy b bata dy k project kasa bana ha fail tuo ni huwa .ma ny b banana ha ma ny uni my submit karwana ha. or project k part kaha sy buy kiye hy.
Best Ever Diagram presentation on Actual Circuit Board Jai Engineer Jai Hind
You do not know you are reviewing, but your ideas are beautiful and we hope that they will be clearer and without abbreviation because some people do not have an electronic initiator
Great useful circuit with simple technique to make the board ! Thanx ! 🌹
Excelente video, muy bien explicado, mil gracias. Saludos desde Bogota - Colombia.
@TechStudyCell
3 жыл бұрын
thank you
Die hier gezeigte genauere IR - Reflexlichtschranke mit dem Diff OP LM 356 ist hier besonders recht gut konstruiert. mit dem Diff - Infrarotsensor - Eingang. Besser als die alten IR - Bewegungsmelder. Der CD 4017 ist hier der Red like - reine analog IC Schalter (natürlich ohne Redinductorrelais). Tolle Schaltung.👍👍👍
So simple way for teaching
Man thanks for this awesome project u really awesome made this without a pcb with a clear layout ❤️
@TechStudyCell
2 жыл бұрын
Glad you like it!
@nitinpatel5447
2 жыл бұрын
Sir ye project kaam nhi karta maine Banaya or comment me bhee bataya hai...?
@mirzahussain9380
2 жыл бұрын
@@nitinpatel5447 tumhe banana nahi aaata ye kam karta hi maine banaya hi
@msfreefire7575
2 жыл бұрын
@@mirzahussain9380 did your work properly
@yashdahibhate7517
Жыл бұрын
100% Working hai kya??
THANK YOU QUITE A LOT!!! You are A Teacher. So thanks again.
@TechStudyCell
3 жыл бұрын
You are welcome
@satishagowda4752
3 жыл бұрын
Aa@@TechStudyCell and a did
Very nice job, 👍👍👍👍👍👍👍👍👍👍
I'm searching for a long time without making arduino nano but you make it bro
@TechStudyCell
3 жыл бұрын
Thanks
@isurun
3 жыл бұрын
Try with a PIC lot more easier than ardunio
@tanveergsaudagar
2 жыл бұрын
@@TechStudyCell Sirji isme 5v dc Diya gya hai extra ye kisliye hai
@tanveergsaudagar
2 жыл бұрын
@@TechStudyCell Sirji isme 5v dc Diya gya hai ye kaise or ye connection kahan hoga
@palkaushik87
11 ай бұрын
How to use the circuit in 220v input?
Very nice job Sir. Frome Pakistan Muhammad khalid khan Electronic Shope Clifton karachi. Thanks 👍 a lots Respactable Sir
@study_tent
6 ай бұрын
Can you make my final year project
It would good if you explain how it work. Please describe working principle
Hi, I need a sensor switch to turn on a light (110VAC) when someone sits at the table, and turn off when he leaves the table. Can you show me how to do it? I do not mind getting an off-market product, but how to wire it to the lamp? Thank you very much!
@dhineshd94
2 жыл бұрын
Use flex sensor in the chair when a person sits the hair will flex backwards so that the sensor attached to it when there is a flex detecked the value will change to 1 and the program with Arduino or Nodemcu will switch on the light when the person leaves the sensor will compress and the value changes to 0 so that the light turns off hope it's helpful ✌️
Your projects are save the electricity
Awesome, it would be useful if you also give a link where to buy these components online and how do we package it (I mean how to get a outer box where this pcb will fit in?)
Thank you bro. I am not sure if the same can be used to room light control. Because I may enter the room triggering it ON. But somebody else might come to visit me, in this case he should trigger it OFF again. Right ?
@TechStudyCell
3 жыл бұрын
Yes. It can be used for toilet light
@vinittomar4515
3 жыл бұрын
Use two IR sensor and count +- entry based on the two IR reading( if first sensor turned on and after that 2nd sensor turned on than entry count it as +1 and turned on the lights) we did similar project in colg
No JLCPCB no problem. So creative
Boa tarde. Eu vou montar esse projeto que você publicou ele e muito bom pra usar no banheiro. Mas eu tenho uma dúvida. As pontas dos terminais dos componentes vai servir pra fazer as ligações elétricas? Obrigado. Brasil.
Hi, friends! I'm from Brazil and i lovely your project. What's software do you to used to designed the schematic? Congratulations, i subscribed.
👍👍I am retired engineer. I got interested in electronic projects as hobby, to pass time I have made your project, on PCB. It is 100% Successful, very good circuit & reliable. I have tested & using since a month without any problems. HATS OF TO YOU. Suggestions: 1.Fitment in electrical switch box. 2.Make aware that it is effective for 1inch to 5 inches approx 3. Setting of 10 k Pot - procedure 4. Precautions like ckt checking with Multimeter , use of heat sink while soldering of parts , no messy soldering etc I wish you release ckt diagram for Remote Control Switch of light & fan ,after rigorous testing. I wish you will release part 2.0 ,with PCB & above sugg , for fresh subscribers. I wish ALL THE BEST
@mahaali89
2 жыл бұрын
Can you tell how to fit it into the electrical switch box?
Hi I make this project its working good it is very easy to make this project thanq for circuit diagram thanq somuch
@Believer_268
5 ай бұрын
Hey bro 🤗 I am making the same project. But the measurement on the print on A4 paper is different than the given...how did you get proper printout? Plz help..😢
Can we add LDR so that it only activates during darkness?
Hi, can you send me circuit to make it by pcb manual by print at glassy paper and print at copper pcb
@TechStudyCell
2 жыл бұрын
Download the PCB layout from article. link is in description.
nice gives me confidence
Very Didatic!! Congratulations from Brasil!!!!! I subscribed to your channel!!!!
@TechStudyCell
3 жыл бұрын
Thanks
hi iwas one question the pot raplace 20k and relay is 12v can cahnge any part of project because i make it but relay continue is working how to
Behtareen bhai jaan bahot ala
Your project is very good and admirable. I also want to make your project, but it's not easy to buy parts. I'd appreciate it if you could tell me if there's anything in the set or if it's a purchase site.
nice diagram.
Good job brothers
I really like your videos. Tks
@TechStudyCell
3 жыл бұрын
Welcome
Hi boss i do your projet he work i like it , is very intersting
Very good and amazing project, i made this but motion is not detecting after 1 inch, it's detect from 1 inch only, please help
@junaidhussain3051
Жыл бұрын
bro can you plz tell me the name of the component that is below th 1000UF capacitor
Bhai ye apne circuit me out - gnd -vcc ke liy jo terminal nikale h uska kya use h bhai, muje please jaldi se jaldi reply krna.
Please make a video on Hall Censor working.
Excelente joven, muy práctico. Si ud m permite lo usaré en una idea.
Good job👍👍💯
@TechStudyCell
3 жыл бұрын
Thanks
Hi. Me simbal edala thiyana vidiha ganna puluwan kamayak thiyeda
Hello ! Thanks a lot for the video but please, can I see the step by step soldering of this circuit ?? Thanks in advance
Can you inbuilt the 220v to 5v circuit in the same board
Do we use 220 volts without any problems?
@industron22
11 ай бұрын
kzread.infoZYz5hGpKyIQ?feature=shared
Parabéns pelo trabalho! Ótima aplicação do circuito.
Ilmu yang anda. Berikan sangat bermanfaat buat kami terima kasih👍👍👍👍👍👍👍👍👍💯👍💯💯
how much do all those units cost An esp8266 and a relay with a motion sensor is all you need. A little programming experience needed. With that you would pay 3 bucks at most for the 8266 about a dollar for the motion sensor and about 2 to 4 for the relay. so from 6 to 8 dollars. and with the 8266 you can set a time length for how long stays on.
How long the light glows once you cross the sensor (inside the room). Does it have time setting.
@bp2791
3 жыл бұрын
please give replies
@power45118
3 жыл бұрын
The light will glow untill you cross the sensor again.
Bro god bless you
@TechStudyCell
2 жыл бұрын
Thanks
Superb sir.....getting person counting
Nice invention 👍🏻
Very good Congratulations
Very good job... High demand
Ye kitnay volt pay work kray ga
Very good thing sir I like this very much
Very very super & ex lent
@TechStudyCell
3 жыл бұрын
Thanks
dear sir thanks alot i was also seraching for thus project and special thanks for the pcb diagram i printed it out and made circuit without any glitch
@TechStudyCell
3 жыл бұрын
Thanks for the feedback
@sarthakkumarmishra513
3 жыл бұрын
Contact me for business
@Believer_268
5 ай бұрын
I am also trying for the same project but the layout after printing on A4 size paper doesn't come out as the required measurements..😢plz help how have you printed it?
@WomenFitHealth
3 ай бұрын
@@Believer_268 😃
Sir pls pls tell wher i can get these items in online i didn't get
Nice thing of energy saving item.
Thanks is not enogh for this great mind I wish you all the best
@TechStudyCell
2 жыл бұрын
Thank you too
Maximum Distence not explain ?
@atech.industry
2 жыл бұрын
By add variable/R you can control the sensing distance
@drjeer
2 жыл бұрын
@@atech.industry where to add ?
@waghmare35
Жыл бұрын
You can set distance reng by using 10k trimmer
@sajidabbas9124
Жыл бұрын
It's Ac or Dc?
@user-sf7es9qy6o
Жыл бұрын
@@waghmare35 that is no trimmer, it is preset or varieble rasistor
The LM358 is the worst chip I've every worked with. I will never use that chip again. Instead, I will and have used the U2531B chip. This is an amazing little chip and does an extremely good job with IR leds as an IR receiver.
sir I make it but not working . i can't finding problem please help me.
@Expensivedna
2 жыл бұрын
Me to
Fikrine sağlık kardeş başarıların daim olsun
I really like your videos
@TechStudyCell
3 жыл бұрын
thanks
Hi, i like your video. But, how about using "230VAC to 5VDC (3W) Converter/Regulator" to supply our sensor and also the relay instead Phone Charger. Thanks.
Thank you very much for the project.
@TechStudyCell
2 жыл бұрын
Welcome
@yashdahibhate7517
Жыл бұрын
101% working hai kya??
Nice useful project.
No.1 fan from India 😁😘❤️
@TechStudyCell
3 жыл бұрын
Thanks
@DR-xz3dk
3 жыл бұрын
@@TechStudyCell thanks for the reply sir😁
Very very nice project ❤❤❤❤
Sir light or relay not use tell me I'll use relay module
Hi dear. You soldered a connector in between 1000uf capacitor and Lm 358p ic, what for that ? Nothing connected any thing to that? Pls tell me tnx
Great Work
@TechStudyCell
3 жыл бұрын
Thanks
Is there anyplace I can find a board already made? I am trying to find a motion activated security light with IR lights instead of visible lights. This will allow my security cameras to see farther when something trips the light, but the thing that trips it wont ever know. Thanks.
Which component did you put in out, gnd and vcc points? Please reply I almost made the circuit.
Wow Bhai Ap to 🧑💻🧑🎤🧑🔧 hei🧑💻👍
Good project & very easily explained
@TechStudyCell
2 жыл бұрын
Thanks
@yashdahibhate7517
Жыл бұрын
101% working hai kya???
Sir plz tell me what you have connect for vcc out and gnd we have mini project on this so we decided to make this project there is a small problem we don't know what you have to connect for that
Great bro 👌 👏 👍 🙌 🙏
@TechStudyCell
2 жыл бұрын
Thanks
I want to ask you that the lamp and pluck we have to connect each other or separately please tell me. And I have another question that you have taken some yellow color is this a wire or something else.
work great ,thanks for this nice project
Very good
Do we use an AC voltage of 220 volts without any problems?
What you think to switch the power with a MOSFET?
Very nice Superb
@TechStudyCell
3 жыл бұрын
Thanks
Pretty cool
Glass materialneyna adhi dhaniki baduluga inkemaina use cheyocha
I have done it by seeing your circuit diagram as shown in discription link but my circuit isn't work
saludos desde colombia excelente trabajo
Your project is very nice and useful.👍 I made this and it's really cool.🤘 The range of the sensor is very less in this, please guide how to increase it.
@TechStudyCell
Жыл бұрын
please watch the recent video on motion sensor
@SadrulHaque
Жыл бұрын
@@TechStudyCell where is the link of recent video..plz provide
@pavangoudar3998
Жыл бұрын
Bro it's taking program
@chandrikapaul3704
3 ай бұрын
Hi, I'm making the same project buts it's not working. Can u help if possible
Your explanation is simply superb. So i subscribe your chennal. Please upload a video for spot welding machine to weld li-ion battery
Very nice project and parts payed out well. How can I get a print out of the circuit board you used
@TechStudyCell
2 жыл бұрын
Check description
Very excellent video many thanks
@TechStudyCell
2 жыл бұрын
Welcome...
can I replace this switch with the main switch? Like i want to install it in my home without wires looking like that. Can I use the wires that already connects to the main switch from inside the wall?
Clear soldering diagram
Sir, can we use a 5v dc led light instead of 220 v AC bulb? please reply anyone if you know, I wanna make this project
One dought if one person is going then the light is going to on and of what happens if two presons go into the door it remins on state or it goes of state
what happened when another person entered in room. means two persone one by one. It's become off or remain on??
I don't have two tarbala ir receiver so how can I make it with tsop please tell me
For this video you deserve a like, subscribe and big thanks
Nice work
@TechStudyCell
Жыл бұрын
Thanks
thank you very much sir for sharing this idea and I'm interested on it. I have only 1 question sir, is it the same materials needed for 220v volts supply? If not kindly update me sir, keep up the good work sir.