Hope you guys will like it 😀👍

@adilahmed873

4 жыл бұрын

CAn i use dc motor plz tell me

@MakeDIY9

3 жыл бұрын

Yes

@Harshsharma-ew9bk

3 жыл бұрын

Which plastic sheet you will use in this for making this fabolus car

@inoskrv6857

3 жыл бұрын

Where is Arduino Uno

@kavyakonathalapali1538

2 жыл бұрын

Hey can u show us how the app is made?

Well done i made this and it worked for me in first time

This is absolutely amazing I tried making it and it works!!!! The instructions are very well explained, but if it had front light features it would have been a bit better. Anyway an amazing project with an amazing explanation it's just very awesome 👍👍👍👍👍👍❤❤

Great work !!.....can you please make a video on automatic and manual modes of operating of any one of the actuators using NODEMCU.... please

Thank you so much bro because i made this project and it also came successfully.if we do per the circuit diagram it works properly

Hey I have just orderd esp8266 node mcu from maker bazar but it doesn't look like your one like in your module there is a sign of plus after wifi but this is not in mine case and I have also orderd the same thing as you mentioned in the vedio esp8266 node mcu modle so will it work this and what precautions should I take while making that so any components not get damaged

Can i use l293d motor shield instead of driver

Nice info, thank you for sharing it :)

Node mcu have male jacks so if i use female jumper wires will it work?

Can I use mcu esp8266 ch340 for this project....?

How did you connected the 11,1V in Esp8266 5Vin ? Should you explain the connections diagram, please? Thank you.

Tell me node mcu coad can we are doing coading without connect moter driver

Can I use 9 volt normal battery or Lithium ion battery ?

I have esp32 30pin, can i use it?

Was there a special cable used or we can use charging cable

plz suggest me another motor with more torque power and with high rpm because i need it for robo car race . I need modification in this only .

bro plz help unable to move the car one motor is faulty but the rest should work right?

im using mini L298N that have only 4 pin on commond channel. then i using only 2 motor for foward backward and turn left right. then i copy the code. but it turn on all motor. can you write a code for that one?

Can we use single/ single two moter??.i tried only two motor ..front rotater for left right and back for for run the car....but its the problem that two motor can't run one by one...plz help me..

Can I apply same code to my car which has only two wheel not for wheels car

It's really amazing 👏 thanks for telling the parts price in description

@MakeDIY9

2 жыл бұрын

You are welcome 🙂

Good day sir, Amazing project. I want to ask you sir, Can I use 6volts normal toy motor. Please advise . Thanks With regards

Did you control this over the wifi of bluetooth

Battery ko reacharge kese karenge nodemcu se kar skte hai kya

Nice video Thanks 🇧🇩🌹

Bro which cable you use for programming

While giving power supply to driver the light glows only when i connect it to 5v and not to 12v!i have tried using many battery also but light in driver glows only at 5v

Só funciona se estiver na mesma rede?

What is the maximum number of votes I can use in the nodemcu?

Can i interface metal detector sensor in it? And if yes how and how can i modify code accordingly.

Great work

bro.. when i press up arrow key it goes left and when i down arrow right. what could be wrong ?

Please give the link of these plastic sheeets

Can i do it with l293d...? Without node mcu And what will be code then....?

Good tutorial,

Very interesting video :)

What application we have to install to operate the car

how much distance it will get

i have one issue... When i click forward it goes forward so well but when i click back wheels of right side donot move

how to control it with flysky transmitter?

ESP32-CAM WiFi (cemra ) kese lagayenga plz sir reply

Um at 0:42 what is that wire called? Those wires that is color blue and yellow?

thnaks

In code after finishing the port is disabled and thus I am not getting output what will be the reason

How can I attach extra sensors to the car?

How did u connect 11.1v battery to 6v motor

Bro which software is used to dump

Bro after few minutes it will run continuously or stop automatically what happened in this situation bro tell me please

Computer me kese WiFi module ko program set karte hai

Hello bhai help me ye jo coding he esko instal karna hai jo aap ne description me de hai NodeMCU WiFi controlled Car Code:

Mu node mcu wae very heat please help

Tienes algun link del video de como creaste la apk movil?

Not Working. When I press the back button on the app, the led on nodemcu is turning on and off. i used old version and latest version of the app.

Speed slider and couple of movement doesn't work. I don't know what I did wrong:(

Can we make a horn and light?? If yes then please refer a code for that

Can i control it with internet..help.me..sir

Broo I've followed all the steps uploaded the code connected to the new wifi even tho it says no internet just like urs but no response frm app pls help broo tomorrow submission date pls reply quick broo

which software using for coding ??

What's is the range 🤔 Plzz reply ky 😆

can I use a bigger motor & bigger tires?

@MakeDIY9

3 жыл бұрын

Yes you can but use good motor and good batteries 🙂

супер!!! молодец!

Hello, I made this car and completed all the steps, but Im having some issues with the final result. Whenever I tell it to move, it turns in a clockwise motion, so the wheels are spinning in opposite directions. I read the troubleshooting and it said to change the motor wires. Do you mean I have to replace the motor wires, or flip their position? Thank you

@ammark3324

2 жыл бұрын

Hi I fixed the issue, you just unsolder one side of motor wires and switch them.

@MakeDIY9

2 жыл бұрын

Yes bro 🤜🤛 😃

what is the app in apple to control the car

Sir isme mobile se programming kese kare

Bro can I use 9v high watt battery instead of lipo polymer battery

@MakeDIY9

3 жыл бұрын

Yes

it can climb at 45degree incline

Bro,I've done every step but in final when I'm giving forward controll it doesn't work.... Tell me solution

Bro my car is not running. When i press the down arrow the nodemcu built in led is blinking. I don't know what's wrong 😔

Can i use esp 01 instead of nodemcu plz reply i want to make this project without buying the nodemcu

@MakeDIY9

3 жыл бұрын

I have not used esp 01 bro sorry bro I can't confirm you the answer to this question ☹️

how to charge the battery ?

Cool project. I tried to built one. Car runs for few seconds and then nodemcu gets turned off. When i connect to nodemcu again and run the car it gives some beep sound. Please help me with this.

@MakeDIY9

3 жыл бұрын

Battery issue buddy

@homethings6382

2 жыл бұрын

Same is it reqlly battery issue?

Can we make this with help of 180 motor and 10.5 volt battery

@MakeDIY9

3 жыл бұрын

yes

How to build the app control?

i am in a very tough situation to buy a new esp8266, mine just turned off after i build my wifi car and never turned on, everything looks okay, but it doesnt work, if u help me, i would be ever grateful.

@MakeDIY9

2 жыл бұрын

Node mcu may be damaged

it is nice project bro....thank you for sharing

@samihasan1734

3 жыл бұрын

nc. i try this 🙂

Hi bro can i have the source code of the app to control the car? I need it cause i join competition to make rc car object mover

Will it turn or move forward backward and I would like to tell you people that whole material cost rs 500 without lipo battery

@MakeDIY9

3 жыл бұрын

Yes bro it will work use any battery of 7v to 12v. 🙂

@miqdadagilamarullah

3 жыл бұрын

@@MakeDIY9 how about 9v battery? Is it ok ?

Sir in this project where is Arduino Uno?

Where is programming link

We are doing coad with android phone

Everything is OK but app doesn't run. It says it's for older version of android.. So what's next?

Can we put rasperry pi camera and code it to stream on html?

@MakeDIY9

3 жыл бұрын

Bro I am not that much familiar with raspberry pi. But surely I am in learning phase and will try it in future. ☺️

Dear sir it can only use lipo battery??

@MakeDIY9

3 жыл бұрын

No any battery of 6v to 12v

Sir When I press the forward button to run my car it doesn't stops and keeps moving. May I know what's the problem. I AM talking about Bluetooth one

@karanshukla2521

3 жыл бұрын

Code is wrong

I LIKE IT SIR

@varadpatil5636

3 жыл бұрын

THANKYOU SO MUCH

@MakeDIY9

3 жыл бұрын

❤️❤️

port option not showing in my laptop what can i do also i have install the driver cp210

@endless7597

2 жыл бұрын

Try another usb

Hi bro I am also done this type of project but there is a problem

does my phone and the car need to be connected to the same wifi?

@MakeDIY9

3 жыл бұрын

Basically yes. The esp8266 creates a password protected hotspot. As the coding part I showed SSID name and password that will be the hotspot name. After connecting you can control the car with your phone. 😉

Please make an video with 18560 battery

@DeathTempler

2 жыл бұрын

That's simple. Pull Aim Squeeze Sweep

Is this operates up-to to unlimited range.

@MakeDIY9

3 жыл бұрын

This car operates through Wifi. So, the range is pretty high.

Bro ,when I am trying to compile it is saying that " error compiling for board NodeMCU 1.0(ESP-12E Module) ". And in the tools > port > ?. There is no such option which you have shown in the video Please reply fast

@MakeDIY9

3 жыл бұрын

I have pasted a link please check it carefully

@indrajeetbanerjee3893

3 жыл бұрын

@@MakeDIY9 Same problem here bro...

yesterdday i could open ypur link but now is crashed...

When I make this car it's not working When i press back button only right side 2 wheel rotate

Which video editing software do you use brother

@MakeDIY9

3 жыл бұрын

Premiere Pro

Bhai 12v ki battery use kar sakte hai kya

@AnkitYadav-es6dr

2 ай бұрын

Yes

How fast do you estimate this car speed?

@aniketroy5525

3 жыл бұрын

300km/HR😂

Why is showing esp8266 failed to download

U should have used a breaboard for the connections instead of soldering , it saves time and effort both

@aryanthakur1793

Жыл бұрын

No breadboard smaller than this mcu

@bhuvaneshs4032

Жыл бұрын

​@@aryanthakur1793 there are mini bread boards

Can we use macanum wheels

@MakeDIY9

2 жыл бұрын

New video in January exactly this topic 😃

U did soldering on node mcu but if i use the jacks on it Will it work??? plz reply man.i m bout to make it.plz reply fast😢.

@MakeDIY9

3 жыл бұрын

Yes it will work

@onlytech4799

2 жыл бұрын

Bhai agar 11.1 volt Battery use karenge to esp ya l298 par load nahi na padega? Please reply