Impeccable amazing carbon fiber work...great Efoil too...but the craftsmanship on the carbon is an art on its own brother...I wish you could build a Fliteboard Efoil board for me...I have the fliteboarod Efoil but would love to have a custom board build by you. great job man

I’m amazed that something with such precision can be made by hand. Incredible.

The most beautiful carbon designs

Incredible. There's levels to everything. Your carbon work is pure art. They way you wove in multi directions was insane! Beautiful work 🔥🔥🙌🙌

Amazing job!

And it’s just that easy folks!😂😂😂

Inspiring as always!

I came looking for regular Fliteboard tutorial then this... 🙌🙌🙌

That is gorgeous!

Amazing! Best i have ever see

This is freakin Awesome!!!!!! Top notch job 👌

this could have gone wrong in so many ways... MAD respect

Looks fantastic. I do this all the time except my parts cost $$$ airplane parts. None of this is DIY🤣.... Between the molds and the process not including the tools. For an average Joe this would be a HUGE undertaking. The resin infusion helps make the entire process a bit easier.

Impressive!

Come sempre lavori sopraffini, impensabili da raggiungere per oggetti fatti in serie! Complimenti per la grandissima cura esecutiva e di progetto nonché la raffinatezza nelle scelte costruttive dei materiali ! Questo nuovo hydrofoil elettrico è una bella realizzazione con tanta funzionalità. Può anche essere un ottimo metodo propedeutico per apprendere gli equilibri dell'hydrofoil prima di passare al kite. Personalmente rimane superlativa la realizzazione del Box wing 2, forme eccellenti e concetti 👏 Con il doppio wing, a parità di alto AR, raddoppia la superfice totale e ne aumenta la resistenza a flessione per via della maggiore sezione geometrica. Saranno anche DIY ma sono opere d'arte della tecnologia!

@Brucecreations77

2 жыл бұрын

Grazie, troppo gentile. Il bello dei lavori artigiani' è che ti permettono di uscire dagli schemi. È pensiero libero, senza vincoli.

Impressionante seu trabalho. Parabéns. Ficaria feliz se você ensinasse a tecer o carbono unidirecional em um tecido tridimensional, como você fez. Faz um vídeo pra ensinar.

damn! im inspired now!

Holy shit awesome work and detail

Damn, amazing!

I would love to know where you sourced the battery, motor, esc from !!!

Creapy perfect

Bruce! So I've got some twil carbon on the top of my board like yours.. I've done a split layup design .. I want to do one layer of twil on the bottom and then put one layer of the nice cool honeycomb arimid carbon that you also use on the bottom. But wondering how I can get nice clean lines and a proper split between the twil and the honeycomb.

🔥🔥🔥

🔥

Hi Bruce, which electric motor did you used. Would you mind to write down pls?

Such a talent, what type of wires are these? those phase wires with the white insulation, I couldn't find any info about those, mind sharing?

@Brucecreations77

2 жыл бұрын

Hi thanks! They are provided with the motor by FlyRodeo, I searched for them but I never find them. They are perfect for such this application because of they have a lot of copper in a thin section.

Wow, that is so beautiful, how did you Cool your batteries in the E foil, because the battery looks to be fairly large. And did it heat up a lot whilst you were using it. Your E foil is the coolest one I have ever seen

@Brucecreations77

2 жыл бұрын

Hi Aedan, thanks. I cooled only the ESC, the battery doesn't require cooling because is correctly dimensioned. I used the foil several times full throttle for more than an hour but never gets more than 40/45°C.

Fantastic workmanship! How did you join top and bottom part of the board?

@Brucecreations77

2 жыл бұрын

I produced a profile that match the two half using one side of the mold and the model

I looked to me like you just pressed together the mast moulds halves with epoxy+milled carbon or similar over the fabric. Is that correct? Or did you vacuum bag each half first? I have done some experiments with both. And also with epoxy+micro balloons. Always a bit afraid to get air pocket and dry spots without bagging. Any secret method you would like to share?

@Brucecreations77

10 ай бұрын

I simply wet-lay the two halves with carbon fiber until they are filled, I take care to remove the entrapped air, I put some extra resin in the middle and close and press the mold. For sure you'll have some little trapped air (very very few if you wet lay properly) but in a full carbon fiber mast it doesn't make any difference in terms of mechanical properties.

@PerWiklund234

10 ай бұрын

@@Brucecreations77 Thanks, I will give that a try.

Amazing! Btw, how does the box wing work?

@Brucecreations77

2 жыл бұрын

Hi, thanks. The box wing works in the same way as the Kitefoil version that I developed through the years. Compared with wings with a similar lift is faster and easy to handle, tight turn.

Hey ! Amazing job as usual on your channel. Will you present what you use in terms of motor and how it's waterproof in the nest part ? Thanks a lot.

@Brucecreations77

2 жыл бұрын

Hi Matthias, thanks, I used a Flying Rodeo motor, It is already filled with oil and there is a gasket on the shaft

@matthiasmeiffred6068

2 жыл бұрын

@@Brucecreations77 Thanks for your answer. Can't wait to see the next part !!

quanto pesa solo la tavola con il coperchio del case?

Is the boxwing being developed into a commercial version?.

@Brucecreations77

2 жыл бұрын

the concept is proven but I'm working on fine-tuning.

what is that green stuff you used for the mould?

@Brucecreations77

Жыл бұрын

It's a mould making material, you can see the reference in the description

😃👍👍👍👍👍👍👍

what the fuck you are so skilled...

ciao, bellissimo lavoro, complimenti! se ti facessi avere una sagoma in EPS riusciresti a farmi una tavola?

@Brucecreations77

4 ай бұрын

Ciao, mi spiace ma non ne ho prorpio il tempo.

What motor is this? Thank you

@Brucecreations77

Жыл бұрын

Hi, it's Flying Rodeo motor

Ciao ammiro il tuo lavoro complimenti volevo chiederti il motore di questo video è lift ? Perché devo chiederti che tipo di esc utilizzi e se ci sono parametri da impostare all esc per non bruciare tutto

@Brucecreations77

Жыл бұрын

Ciao, il motore è Flying rodeo e l'ESC è una trampa 75/300. Per le impostazioni è sufficiente usare il wizar.

@efoilDemis

Жыл бұрын

@@Brucecreations77 si ok ho comprato pure io un motore fly rodeo mi deve arrivare a giorni io utilizzo un altro esc della swordfish x 300A programmabile raffreddato ad acqua facendo girare l acqua come lift vediamo come gira

@efoilDemis

Жыл бұрын

@@Brucecreations77 ciao nel video non capisco come hai creato il pannelli di chiusura del vano , si vede due lastre di carbonio ma all interno come spessore che materiale utilizzi?

@Brucecreations77

Жыл бұрын

@@efoilDemis Ho usato due fogli di www.easycomposites.eu/3d-core-infusion-foam-core, uno da 3 e uno da 5 mm. In un altra tavola sono andato diretto con il 10 mm. Con infusione viene un lavoro pulito, leggero e molto resistente.

@efoilDemis

Жыл бұрын

@@Brucecreations77 ok ma bisogna resinarlo tutto o basta incollarlo con due pannelli di carbonio rigido , perché ho paura che si flette io utilizzo il nido d ape alveolare in aramidica però se posso usare altri materiali meglio dimmi te se come utilizzare questo materiale io non l ho mai usato

Hi Bruce? Would you maybe sell CAD files?

@Brucecreations77

Жыл бұрын

There are no cad files, it's all hand shaped. I did some simulations with the Wing just to choose the profile

hey bruce, is there a way to contact you?

@Brucecreations77

Жыл бұрын

At the end of all my video there is my email

mi dicono che sei italiano, di dove?

Are you on the diy efoil discord?

@thebamb00zler6

Жыл бұрын

There is a discord?!

@Brucecreations77

Жыл бұрын

No, I don't know

Cazzo che artista

@Brucecreations77

2 жыл бұрын

Grazie 😁