I've been building simple DIY rc airplanes for the past year after buying expensive airframes from major brands for big money. My most common design is a simple wing and tail attached to a carbon arrow from Walmart, without electronics $6.00 total and E-flight just came out with the "slow stick" that is a carbon copy of my design for $200. I have to say I enjoy flying my budget builds way more then an over priced $400 foam warbird any day. Once you understand the basic principles of airfoil design the sky is the limit...... Pun intended.....kind of lol. Warm up the glue gun grab a few sheets of foam board from the dollar store and cut, sand and glue until you have something that looks like an airplane and send it 👍 if it doesn't fly do a little more research and try it again. I was at the park maybe 7 times until one of mine finally flew and that is a great feeling.

@beargillium2369

11 ай бұрын

Slow stick has been a design in RC for many many years!

@jordancoleman2402

11 ай бұрын

@@beargillium2369 sorry

@macandfries6765

11 ай бұрын

@@jordancoleman2402 doesnt make you a bad engineer though! you reinvented the wheel without knowing it existed!

@jordancoleman2402

11 ай бұрын

@@macandfries6765 I'm a shit engineer 🤣

Smooth Take-off & Landing, what a masterpiece there...

Kendin I think you've finally made something I think I can build too. I've been wanting to get into the RC hobby for over 55 years... and it's time! Thank you for this video!

@hendrikdebruin4012

11 ай бұрын

I have waited 66 years. BUT none of these supplies are available in the small African country I live in. So never will it happen I think.

@nork7045

11 ай бұрын

Haha this comment gave me a good laugh. “KendinYap” means do it yourself in Turkish and Kendin means yourself… It’s not his name. Good luck getting into the hobby though

Very good looking plane. Looks almost store bought. Flies great!

awsome.i have built and flew rc for a long time.this was a awsome vidieo.thank you

Great video, I've been waiting to see your homemade controller and receiver in use and it was worth the wait, I love your videos. May you make a build using packing foam from appliances. Again great content man :)

So neat clean any beginners can easily learn better and faster..Many Thanks Sir..Hope to see some more..God Bless you Sir

Thank u sir ..... thanks a lot .... we need more such cool long flight time build

great it seems to be super stable in flight great for beginners. I am also building a high wing at the moment (the Stinson SR9 see on the channel) I hope it will fly as well as this one

Lo hace parecer tan fácil, yo arme uno de sus modelos y lleva bastante tiempo y dedicación, mis felicitaciones por cada uno de sus videos.

So cool project 👍👍👍❤

Great video, this is amazing 👌

Excellent content..👌👍👍

Wonderful content❤️

POR ESO ESTOY SUSCRITO A TU CANAL, NO HACE FALTA UN MODELO COMPLICADO PARA QUE VUELE PERFECTO, SOLO HACE FALTA HACER BIEN LAS COSAS. CON UN MODELO BASICO HAS CONSEGUIDO UN GRAN VUELO CON MUCHA PERFECCION. UN ABRAZO Y ESPERO CON IMPACIENCIA EL SIGUIENTE VIDEO

Very nice 👍

Nispeten kolay bulunan malzemelerle yapabileceğimiz ürünler ortaya koymak,, izleyici açısından daha anlamlı. Teşekkürler.

Hi. I am building myself one this weekend😀😀👍🛩️

Хорошо управляется самолётом ещё и без полётного контроллера.

Very nice. I'm going to follow your plan and try it myself. Thank you very much. 👍

şimdiye kadar gördüğüm en mükemmel kanal teşekkür ederiz ve özellikle bu kadar yabancı izleyicin olmasına ragmen türkçe olarak da bize yardım ettiğin için minnetarım

Very nice work, Sir.

Yine harika bir video 👍

It really is a 1-day build, I'll go ahead and try it ;D

an awesome build - congrats. I like your approach of building stuff out of easily available and affordable materials. Where are you located?

The king is back! Abi bekliyoruz videolarını devam!

Beautiful airplane, congratulations for your great channel, tutorials and airplane designs. This aircraft seems to fly amazingly, long flight time and manoeuvrability so I decided to start my foam airplanes building experience with this. Here in Chile there is no depron or any type of naked foam for the wing, only carboard with foam core so I think that might be a little heavy at last, I will report the result. I'm about to start the rear gear but there's some data missing, can you please share some of them, especially the rear landing gear geometry and measures?

Superb !!!

Will the 3d printed landing gear work with the DIY Trainer plane from 2020?

Gotta build me one of these! 😝😝😁🤪🤣👍👍🇺🇲

Thanks to your video, I'm planning to build one. But I have a question. Why do you have to tilt the motor a little bit when you're building it?

@Kendin-Yap

5 ай бұрын

www.balsaworkbench.com/?page_id=2714

@user-zn5lo8cw1w

5 ай бұрын

@@Kendin-Yap Oh thank you very much sir

Bende diyorum neden bu videoyu daha önce görmedim meyerm yeni paylaşmış koca yürekli abim ❤

Built one, it flew so well. Thx

@Syphronix

28 күн бұрын

Any tips for the build? Thanks!

🎉Felicitaciones desde Uruguay. Al fin un avión que vuela como un aeromodelo y no como un avión que va colgado de la hélice y la potencia del motor. Un placer ver volar ese avión. Aaaaaa a y gracias por compartir los planos.

Please please please build a supercub with Alison's using foam whose wing is about 80cm long I need to build one your vedios are perfect

I didn't understand the size of the wing before you cut it and the size of the two layers. And can I use 5mm foam board for two layers?

I will use a long spiral piece to connect two separate wings, but the question is: How will I build the wing elevation angle when I have two wings connected by a long spiral piece? What are the alternatives to using such an angle that gives stable flight? For your information, I am a beginner in flying, but there is a friend of mine who made a plane with two separate wings and connected them with a spiral piece, but I did not. Use this angle and use a straight wing without making a wing that goes up a little??

Can I cut half the depth of the wing and make the winglet move without having to glue the winglet with adhesive because I do not have adhesive?

Nice video. Been watching a lot of your videos on how to make planes and controllers. How do you determine where the front landing gear should be placed? I'm thinking they get placed at the center of gravity position.

@Kendin-Yap

Жыл бұрын

It wouldn't be good to consider the center of gravity for back wheel models. Because the nose of the plane will move downwards during landing and take off and the propeller will hit the ground. I usually place under the leading edge of wing. That is further from the center of gravity.

@bigrenegade7121

Жыл бұрын

@@Kendin-Yap Thank you. That will definitely help me in placing them properly.

Hocam elinize sağlık, aileronu kontrol eden servolari aileronlarin merkezlerinin hizalarına koyarsanız daha iyi olur, kolay gelsin.

El becerisi ustam. Ben de size özenip daha önceki videolarınızdaki gibi bir trainer yaptım ama 30 metre uçtu😂. Bu işte denge ve el becerisi çok önemli.

@Kendin-Yap

Жыл бұрын

Hepimizin için geçerli... Uçurmayı öğrenmek bir süreç.

Tahta çubuklar için hangisi daha uygun? Bambu ya da gürgen ve kayın. Hafif olsun diye bambu mantıklı geldi.

How stable is the rudder after a period of use? Any way to strengthen it?

Ellerine sağlık

alet aşırı dengeli... hocam 2.5 mt kanat açıklığı olan bir çalışma yaptınızmı yada yapmayı düşünürmüsünüz?

Kendin, i have a problem with the transmitter and receiver from your 8ch 2400 meter range. More then 1 servo's react on throttle or yaw. Do you know what i'm doing wrong? Kind regards. Henk Ketelaars (The Netherlands)

If you made a kit of it for sale, I would buy one! :)

Excellent video! Where do you get the motor to propeller adapter?

Question please if I have a motor 1400with esc30 With battery 2200 I have a plane with a long wingspan 84cm With a bird's length of 70cm And wing width 22cm. Can the plane fly well and is it similar to the plane in this video?

hello, great video. hey can you put a mix channel on the homemade radio control?

1st ❤

He used Duct tape on the wings where the rubber bands go but i have a better suggestion as they will still bite into the foamboard to a degree. Pre shape and glue milk jug plastic to the leading and trailing edges of the wing where the rubber bands go, it will completely stop them cutting into the wing! If you belly land foamboard planes then i also recommend the same milk jug plastic for the part of the planes belly that contacts on landing, it will make the plane last and you can land on dirt and gravel tracks with it without damage to the fuse, not just on grass! Milk jug plastic is made of HDPE which does not like being glued, use a very sharp blade and score a diamond pattern into the side being glued and use the blade at an angle so it slices under the surface and not straight down so there is something for the glue to mechanically bond too, it will hold very well like that.

Sir, I do not understand what is the measurement of the place where you placed the long, light-thick wooden pieces, and I also do not understand what is the size of the piece to install the wing before installing it in the first place, when I placed an airfoil and the airfoil stopped and I glued them together.

reis tb2 filan yapsana modelini güzel olur bence hem reklam değeride var ;)

I am a beginner in fixed wing airplanes and now I will be making my first airplane. Do I have to use Gyro so I can fly and how do I use it? Can you explain in a good way ❤️

if i want to use this controller for drones do i need to change code or something else?

Merhabalar elinize sağlık. Ağırlık merkezi videoda mm cinsinden yazılmış galiba cm olacaktı . Takibe devam 💯

uçağın yapımını bitirdik hocam yapısal ve elektroniksel olarak sorunsuz duruyor haftasonu test uçuşunu gerçekleştireceğiz. sadece şöyle bir durum söz konusu, uçak taksi esnasında bazenleri ağırlığı uca verip pervane üstüne düşme durumu oluyor bu da fazla bir sorun teşkil etmiyor. videonuz için teşekkürler

Hi, watching the video, about 10 seconds in you start making wing reinforcers to ensure the correct airfoil. Both are made from 5mm foamboard I believe, one is two layers thick, the other four. Is the width of these reinforcers critical? , if so what should they be please? They are obviously 540mm long for each wing half. Good work.

@Kendin-Yap

Жыл бұрын

Sorry I forgot to add it. I updated the detail page. Thanks. www.rcpano.net/2023/04/19/how-to-make-amazing-stable-rc-trainer-airplane-with-handmade-rc-long-flight-time/

@zhaozhao6148

Жыл бұрын

@@Kendin-Yap can't open the link, can you give the width?

@chrisbolocan8182

11 ай бұрын

@@zhaozhao6148 Lenght: 73 cm (28.74 inc) Wing span: 109 cm (42.91 inc) Flight weight: About 675 gr Center of gravity: 4.9-5.5cm from the front of the wing Required control system: Min. 4 channels, 4 micro servos Suitable battery: 11.1V 2200Mah (Max 2700maH) Suitable motor: 2212 Brushless Motor (980-1400KV) Suitable propeller: 2 Blade 9×6 (9060) Flight Time: Approximately 30 minutes for an average gas level of 38% Wing area: 1976 cm2 Vbar: 0.46

I can't find the insulation foam sheets anywhere. could you send me a link, maybe for a product on amazon that would work

Can I use a whole piece of foam board measuring 100 cm without having to cut it in half and weld it?

If you use a 1000kv He must use a large fan. Does this mean that the fan will hit the ground? How can I avoid that?

@Kendin-Yap

6 ай бұрын

8x6 propeller can be used for 1000KV motor. It's not the ideal propeller, but it works. For 9x6 or 10x4.5 propeller the fuselage needs to be upgraded. In this case, larger diameter wheels can be used. Or the landing gear should be raised.

How long does it take to build one like this.

Where do you get all the specs for all the little pieces on the inside?

*****If I may add - - there doesn't seem to be anywhere that has in stock the basic 3, 5 and 7mm card stock that you specify. It's either out of stock or such a high price that it's unaffordable. Do you have any further suggestions for outlets that have specifcally what is needed and if you could explain what a "panel" is of the card stock - it's dimensions please? Seems everything else is available where you noted - which I am thankful for!

@Kendin-Yap

Жыл бұрын

For Kraft Foamboard and insulation foam, it makes sense to search local dealers in your country of residence. Since it is a large-volume product, it is expensive to procure it from international vendors by cargo. Kraft foamboard; It is a foam material whose outer surfaces are covered with kraft paper. Plate dimensions: 50x70cm. Or it could be larger. It is a light material. Insulation foam, on the other hand, is a fully condensed foam material. Plate dimensions are larger than foamboard. Insulation foam is usually sold in construction-building materials markets. Foamboard is sold in shops that sell architectural models or hobby-stationery.

@d.j.2146

Жыл бұрын

@@Kendin-Yap Thank you very much! I appreciate the response. 🙂

Bu uçağın arkadan motorlu olanı nasıl yapılabilir çok şeyin değişmesi falan gerekiyor mu? Arkadan motorlu buna benzer uçak yaparsanız çok güzel olur.

That is a wonderful stable aircraft! Would love to be in contact with you to exchange project ideas.

Nice project... I will try to build one. Just to clarify if the info at 12:15 related to CG is correct??? that might be ~49-55mm (4.9-5.5cm) instead of 4.9-5.5mm ???

@Kendin-Yap

Жыл бұрын

Yes, sorry there was a typo. But there is correct data in the technical information below the video and on the detail page on my website. CG: 4.9-5.5cm (49 - 55mm)

@TIRCQ

Жыл бұрын

@@Kendin-Yap Thanks and please keep going. You have great projects there 😁

@XXXXXX-wl6zk

Жыл бұрын

@@Kendin-Yap I looked for this information. Thx, nice project. I will try make it. Greetings

It seems that my hobby has already accomplished.but I have a problem how to charge the battery? Hope to give me reply soon.❤️

sir can you write delta wing code or next project for delta wing everythink is done last think is mixxing allgreat i love your work sir keep going

I cannot find the insulation foam board. What else can I use? Can I just use regular foam board?

Tebrikler. Yine güzel bir proje. Peki önceki uçaklardan farkı nedir kararlı uçuş için?

@Kendin-Yap

Жыл бұрын

Önceki trainerdan bir kaç farkı var. Bu modelin gövdeye oranla kanadı çok daha uzun ve dolayısıyla kanat alanı çok daha fazla. Yatay stabilize (elevatör) çok daha büyük. Ve kanat köpükten yapıldığı için boyutlarına oranla çok daha hafif. Tüm bunlar bir araya gelince hem daha kararlı bir uçuş hem de daha uzun uçuş süresi sağlıyor.

Luar biasa sekali kerja anda👍

Hello, is it possible to create a fixed, straight wing without a slight rise in the wing upwards, and what are the reasons for doing so?

@Kendin-Yap

4 ай бұрын

Wing angle is necessary for stable flight. If there is no angle, the control will be aggressive. The angled wing structure is important, especially for those who are not very experienced.

@atheermuhammed2971

4 ай бұрын

@@Kendin-Yap I will use a long spiral piece to connect two separate wings, but the question is: How will I build the wing elevation angle when I have two wings connected by a long spiral piece? What are the alternatives to using such an angle that gives stable flight? For your information, I am a beginner in flying, but there is a friend of mine who made a plane with two separate wings and connected them with a spiral piece, but I did not. Use this angle and use a straight wing without making a wing that goes up a little??

Elinize sağlık, iki sorum olacaktı. 1-) kanatları deprondan değil de fotobloktan yapsak herhangi bir sorun oluşturur mu? 2-) Bende 1800 mah pil ve 1000kv 1045 pervane mevcut. Muhtemelen pilden dolayı daha hafif olacaktır ve motor-pervane kaldırma gücü de sizin kullandığınız motor-pervaneye göre yaklaşık 100 gram daha fazla kaldırma üretiyor. Datasheete göre. Yani bu kaldırma-ağırlık dengesi sorun yaratır mı? Uçağa fazla mı gelir yoksa çok etkilemez mi

@Kendin-Yap

9 ай бұрын

Evet kanatlar da fotobloktan yapılır. Ama fotoblok biraz daha ağırdır. Uçuş süresini bir miktar etkileyebilir. 100gr itme kuvveti farkı önemli bir sorun yaratmaz. 10 inc pervane uzun olduğu için yere sürtebilir. İniş takımlarını bir miktar yükseltmek gerekebilir.

Merhabalar hocam neden batarya kapasitesine max 2700 mah dediniz?

@Kendin-Yap

5 ай бұрын

Kapasite arttıkça pilin ağırlığı da artar. Belli bir ağırlıktan sonra model kararlı uçuş özelliğin kaybetmeye başlar. Bu yüzden bir sınır olmalı. Her model uçak için aerodinamik yapısına ve boyutlarına göre bir ağırlık sınırı vardır.

Perfect ..bro, what size of the brushless motor sir..👍

@Kendin-Yap

11 ай бұрын

2212

Can I use a fan? 8*6 With this model in Motor1400

Can I use 2204 2300KV brushless motor with 15A ESC? For a slow flying?

@Kendin-Yap

Жыл бұрын

You can use it. But high kv (high rpm) is not ideal for slow flying.

It's a really nice model, well made. What is the ratio of takeoff weight and surface load (gr/dm2)? Gerçekten çok güzel bir model olmuş, elinize sağlık. Take off weight ve kanat yükü oranı (gr/dm2) nedir? Es ist ein wirklich schönes Modell, gut gemacht. Wie groß ist das Verhältnis von Startgewicht und Flächenlast (gr/dm2)?

@Kendin-Yap

2 ай бұрын

Teşekkürler. Videonun altındaki detay bölümünde teknik bilgiler mevcuttur. "Daha fazla" ibaresine tıklayarak detayların açılmasını sağlayabilirsiniz.

Üstat elinize emeginize sağlıkl. Bir tane de pusher model yapmayı düşünür müsünüz. Pusher modeller de trainer icin uygun mudur ?

@Kendin-Yap

Жыл бұрын

Eski videolarımda pusher model var. Trainer için çok ideal değil. Burundan çekişli modeller daha stabildir.

may i get for this program arduino nano with lora?

What dimension have those 4 strip foam? That is 5mm foam?! Thanks

@Kendin-Yap

Жыл бұрын

Strip for battery 25 or 38mm, Strip tape for hinge 25mm, Foamboard 5mm, insulation foam 3mm and 6mm

👏👏👏👏

Please make a video for drone flight controller with arduino nano and MPU6050 gyro sensor.❤❤❤

👍👍👍

Is it possible to make a complete wing with a length of 100 cm without the need to cut and assemble the wing?

@Kendin-Yap

6 ай бұрын

There is an attachment for the dihedral angle at the junction of the right and left wings. Angle cannot be applied for one-piece wing. This reduces stable flight capability.

Usta Gemi gibi bir RC araç gelirmi büyük

❤

hocam kanat kesiti kısmında kanadın alt kısmı ve üst kısmıyla olan yükseklik farkı bir kanadımda 1.7cm civarında diğerinde 2cm oldu.bu ciddi bir sorun oluştururmu çok ufak bir fark var yani gözükürde

@Kendin-Yap

28 күн бұрын

Uçmasına engel değil ama iki kanat arasında kaldırma kuvveti farkı oluşacaktır. Kalın olan daha fazla kaldırma kuvveti oluşturacağı için diğer tarafa yatma eğilimi oluşacak. Ters yönde aileron ile dengelenebilir. İdeal olan bire bir aynı olmasıdır.

I've seen all of your videos they are awesome but I need How many foam board sheets are required

@Kendin-Yap

7 ай бұрын

1 x foam (80x60cm) and 1 x kraft foam (50x70cm)

abi depronu nereden bulabiliriz. 10 lu adet satılıyor ve 2 bin tl yalıtım malzemesi olarak . Çok pahalı . Buna alternetif ne kullanabiliriz köpüğe çok benziyor ama ucuz alternetifi var mıdır? eline sağlık

@Kendin-Yap

Жыл бұрын

Depron bir yalıtım köpüğüdür. Depron olması şart değil farklı marka yalıtım köpüklerini kullanabilirsiniz. Bi ara Koçtaş'ta tek tek satılıyordu markasını hatırlayamadım ama... çok daha uygun fiyatlıydı.

hocam artık daha büyük modeller bekliyoruz

Can I use a battery smaller than this size because I do not want to fly for a long time? I only need to fly for 10 minutes

@Kendin-Yap

6 ай бұрын

Yes you can

how do i know if i made the wing right?

Depronu nerden temin ettiniz acaba onun linkini de paylaşabilir misiniz?

Is it possible to use a 100cm wing? Keeping the width of the wing and the length of the plane ❤

@Kendin-Yap

6 ай бұрын

Possible. But the center of gravity will change. And the flight characteristics also change somewhat.

@atheermuhammed2971

6 ай бұрын

@@Kendin-Yap What will I do in this case to keep flying like the video?

Elinize sağlık, sizin gibi kanalların youtube da olması çok güzel. Acaba bu uçak 10 mm lik xps köpük ile yapılabilir mi çünkü 5 mm lik fotoblok bulmak zor

@Kendin-Yap

Жыл бұрын

10mm biraz kalın ama gövde genişliğini ona göre uyarlarsanız olabilir tabi ki

Keşke tanışma veya konuşma fırsatım olsa sizle🥺

I'm still new at this, can someone answer me. What will happened if i using 40A esc in this build instead?

@Kendin-Yap

Жыл бұрын

You can use 40A ESC. No lower than the recommended current capacity should be used. But you can use higher. The maximum current drawn by the motor does not change.