Now Bigger secondary coil with this circuit click to watch • Diy Single Mosfet Powe...
Жүктеу.....
Пікірлер: 251
@ngoweyseong37382 жыл бұрын
I like the way u secured the pvc bobbin with 2pcs of half moon plastic. Nice!!!
@TechIdeasAG
2 жыл бұрын
Thank you
@aplacetoimproveteslacoilin3721 Жыл бұрын
When most people think of a Tesla coil, they imagine a large, imposing object with sparks flying everywhere. However, it is possible to make a tiny Tesla coil that is just a few inches tall. This coil can be powered by a small battery and can produce millions of volts. The key to making a tiny Tesla coil is to use a high-voltage capacitor. This capacitor will store the energy that is produced by the battery and release it in short bursts. The secondary coil of the Tesla coil should have a very large number of turns, as this will increase the voltage output. The final step is to create an ignition system. This system will create an arc between the two coils and will generate the sparks that everyone loves to see. By following these simple steps, you can create your own tiny Tesla coil that packs a powerful punch. Theoretically yes!
@harms123
Жыл бұрын
You're not gonna be making million-volt arcs with batteries.
@milespeterson5049
Жыл бұрын
I need help my tesla coil is not working! I smell burning!
@harms123
Жыл бұрын
Sure if you have some massive fuckoff lipo you can but that's about the only exception
@ankanpradhan9724
Жыл бұрын
But more the no. of turns in the secondary coil the mosfet will get hotter and hotter (not sexy hot). So I suggest to use a high power mosfet like irfp260n or, even better irfp460n
@harms123
Жыл бұрын
@@ankanpradhan9724 wot?
@ianhosier4042Ай бұрын
That is a high current draw even at 9v. Is it the current or voltage that controls the output? I was always wondering how to properly bias a mosfet in a slayer circuit so thanks for that one.
@soriatel Жыл бұрын
at what frequency does it resonate?
@antoinedevos37653 жыл бұрын
Thank you for this video 👍 It's a very good idea 😉
@fquimico10 ай бұрын
Hello friend, can you tell me what voltage and amperage you used? Grateful!
@darkknightplayerz67521 күн бұрын
Can we use thicker Cu wire for it?
@Gamesindo404 Жыл бұрын
how do you make the electricity above become quite large?
@Bllak999Ай бұрын
Amazing video😮😮
@vaibhavsrivastava745511 ай бұрын
I have B100K potentiometer can I use that instead of the 1k ohm?
@rupeshpatil55682 жыл бұрын
Work better with IRF540 MOSFET because it has a higher switching frequency
@hpvide
2 жыл бұрын
Can I use 44
@hungdpiqn
Жыл бұрын
do you know every coil have they own resonance frequency
@harms123
Жыл бұрын
It also has a higher on resistance, which means you generate more heat. You don't need fast switching if the resonance frequency of the secondary is low enough.
@milespeterson5049
Жыл бұрын
Oh interesting. I was going to order the one in the video but are you sure it will work with IRF540? did you test it out for yourself?
@rupeshpatil5568
Жыл бұрын
@@milespeterson5049 Yeah my setup still works perfectly fine.
@user-mq7nn7qo6r2 ай бұрын
Can we use more wide copper wire
@Its_Manan01 Жыл бұрын
Buddy what is the cost of all these ?
@amutha1652 Жыл бұрын
What toroid did you use
@Alvifiction4 ай бұрын
can we use 12v power and 2amp?
@ankanpradhan9724 Жыл бұрын
I have also tried to make one but I would suggest that to use IRFP260N mosfet with 24v power supply
@b-beluga4510
Жыл бұрын
I ve used irfz44n and it works fine. Can i use 24 volt with this system?
@OmletArcadeOfficial
4 ай бұрын
@@b-beluga4510Yes you can use it because it works good for me
@sree137918
2 ай бұрын
@@b-beluga4510your mosfet will probably die with this circuit at 24v because of excessive heat created by it.
@creativesuraj32633 жыл бұрын
Amazing
@soriatel Жыл бұрын
does this burn?
@Juniorfinger999 Жыл бұрын
Wow amazing bro
@adrian-brawlstars9296 Жыл бұрын
Does a 1000uf capacitor work?
@eswarelectronics42053 жыл бұрын
Superb
@kantarao568411 ай бұрын
Except 47ohm resistor which resistor we have to use to get spark
@thisurasenidu2 жыл бұрын
Can it be powered with 12v 2amp
@webseries1935 Жыл бұрын
Please reply.. working on this today.. still 5 am i am awake with this
@ateebbaig77703 жыл бұрын
Awesome man I will try it ....👍👍👍 I love your trick of winding the coil really awesome Idea. Keep it up 😉
@manawadugeisuru27673 жыл бұрын
It's great.
@maximtem67172 жыл бұрын
увеличь количество витков вторички до трёх, проводом хотя бы 2,5мм!!! и увидишь что произойдёт!!!
@electric_mix2 жыл бұрын
Nice
@rodriguezfranco38392 жыл бұрын
Great I have a few IRF540 and I was thinking if I could make a slayer with those since 2n2222 are too weak , thanks for this tutorial
@aplacetoimproveteslacoilin3721
Жыл бұрын
Replacing the spark gap with transistors IRF540 and 2n2222 makes Tesla coil smaller, more efficient and easier to build. The transistor acts as a switch to turn the current on and off in the primary coil. This just resonant nature of Tesla coil creates high voltage and frequency which is used to create sparks.
@harms123
Жыл бұрын
@@aplacetoimproveteslacoilin3721 Okay? That's not what he asked?
@aslamaslam.31452 жыл бұрын
How did you make that power suply
@kdhananjay73812 жыл бұрын
Can we use it with 10k pointometer
@BoyAmg7 ай бұрын
What is the Golden wire after 47 ohm
@keithhufnagel93422 жыл бұрын
What would happend if i keep turning the potentiometer
@hajerromdhani2678 Жыл бұрын
أحسنت لقد أذهلتني
@waynebagnall3611 Жыл бұрын
What about using 5 or 6 turns of 1.5 or 2mm wire for the primary coil. Also, maybe using a larger capacitor, or 2 or 3 in series.
@Mint474 Жыл бұрын
POV: you thought this was a small easy diy project
@gaynzz6841
3 күн бұрын
you can make it small and easy. all you need is to wind a coil, and 4 components. the amount of complexity is the designer's choice.
@rakesharks6643 Жыл бұрын
What source did you use is it dirext or alternate current ?
@PlasmaPro8
Жыл бұрын
Dc
@milan723 жыл бұрын
wow! Great,
@thilininishadari9299 Жыл бұрын
Can I use another potentiometer
@JaviersDIY3 жыл бұрын
Impressive
@user-nk3sc6cx5x Жыл бұрын
Does it work?
@RICKSTUDIO-vr8os2 жыл бұрын
Please show the circuit diagram without potentiometer
@sohammane8338 Жыл бұрын
Hello will it work with a 9v battery small one
@BrysonB-pp7yo2 жыл бұрын
6:40 what is that thing powering the tesla coil?
@frank676283 жыл бұрын
well done my friend !!!
@sana.m2 жыл бұрын
What music did you use 🤔
@abhijayjayan6326 Жыл бұрын
What is the gauge of drain pin
@amutha1652 Жыл бұрын
It's works bro.thank you for the tutorial!
@prashantpatel8290
Жыл бұрын
Hi what gauge did you use? I am not getting 0.07mm wire anywhere
@amutha1652
Жыл бұрын
@@prashantpatel8290 I used 38 awg magnet wire
@prashantpatel8290
Жыл бұрын
And all other parts remained same? What Mosphet you used? Is the spark good size and powerful?
@amutha1652
Жыл бұрын
It's a bit small
@amutha1652
Жыл бұрын
The same mosfet
@muhammadnur1672 жыл бұрын
Untuk membeli kawat lilitan x ini dimana ya...?
@editiorsingh-8248 Жыл бұрын
Sir, 1k potentiometer replace 100k potentiometer use kar sakta ha
@AnilKumar-uv6fn10 ай бұрын
can it glow cfl blub or tube
@kolakeshobha4829Ай бұрын
Can 500v 4.7 capacitor work
@hasinikaushalya8739 Жыл бұрын
50k protect and 250v 47uf capacitor messed up? Replay me..
@guruxgamingoffical8925 Жыл бұрын
Can i use 10 k potentuometer
@milespeterson5049 Жыл бұрын
Does anyone think that a electrolytic capacitor might blow up easily? I do not feel confident buying a $10 capacitor and it blows up. So should I get a film capacitor instead?
@adityasudershan9629
Жыл бұрын
Yes electrolytic capacitors can't handle that High frequency so using a film capacitor is better!
@urbeautifullboy_ Жыл бұрын
what is the thickness of the copper wire you used in coil
@JonathanGameHD
8 ай бұрын
0:28 0.07 mm diameter
@xhacker7732 Жыл бұрын
I want to try this
@rajnadi90332 жыл бұрын
I need 0.07mm wire please kidher se mangvana hai vo bataiye
@thilininishadari9299 Жыл бұрын
Is it burning or not
@MuhammadDaudkhanTV1003 жыл бұрын
Really good to hear
@the_royalgamer4842 ай бұрын
Bro ,we can use C.P.U cooler in place of heat sink with fan ?.
@TechIdeasAG
2 ай бұрын
Yes, it will also work
@mousumisarkar66853 жыл бұрын
It's very good 👍 👌.
@didakpram29756 күн бұрын
Very interesting 👍👍👍
@TechIdeasAG
4 күн бұрын
Thank you! Cheers!
@webseries1935 Жыл бұрын
Should this magnet coil is need to be insulated or not?
@erikzidan2601
3 ай бұрын
Its just copper with isolation, and of course you need it otherwise you would short the secondary
@webseries1935 Жыл бұрын
Not working.. please help me.. capacitor is not even charging.. what should i do?
@milespeterson50492 жыл бұрын
Help! I don't have that weird capacitor. I have a 3.3uf one but it's rated 50v. can you help? will it still work? please respond.
@milespeterson5049
Жыл бұрын
@Smaxi botYeah I will just order a 450v capacitor. on the internet along with the IRFz44n Transistor.
@mike289homebuilt5
Жыл бұрын
Miles. One I built/ Ludic Science/ Triple Primary Slayer Exciter . I only used one transistor and Two medium Led (backwards) as substitute for diodes. Any of these slayers substitute 1/2 watt potentiometer for the Resistor that way you can turn the power up mount a Cfl on top of the secondary pop bottle plastic. The Mosfet circuit one is better but they both work.
@milespeterson5049 Жыл бұрын
Help, my tesla coil is not working again. I got the same transistor the resistors and even the same capacitor, but every time I fire up the circuit I get no output from the tesla coil, and If I turn the potentiometer, I start smelling a burring smell, no smoke but not good for my components. why is it doing this? and how to fix it? Please comment below. 😃👇👇
@adityasudershan9629
Жыл бұрын
Flip the connections of primary
@milespeterson5049
Жыл бұрын
@@adityasudershan9629 I did try that and I still smell burning. what am I doing wrong? its at 12v so it can't be voltage its 1 amp so that's fine. what's the problem is it wired wrong maybe?
@legendgamingff8796 Жыл бұрын
Can we glow CFL bulb
@amutha1652 Жыл бұрын
What is the gauge of primary coil? Please reply as I need it very much
@guru6322
11 ай бұрын
I made one with 32 guage works fine but if you want high voltage output then go for 20 - 30 guage wire. But remember thinner the wire gets chances or wire burning increases.
@angelogaming9538 Жыл бұрын
Hi sir what is the name of the device that you use when you're measuring sizes
@abhijayjayan6326
Жыл бұрын
Vernier calliper
@thoiencuibap42742 жыл бұрын
Kiểu này mình thấy tia ok hơn kiểu kia😄
@dy.experiments28269 ай бұрын
Me I used 0.4mm of magnet wire, and I need a mosfet or transistor that can be input of 12v dc.
@rdencysАй бұрын
Wow, will the coil warm ?
@TechIdeasAG
Ай бұрын
Nope,
@TechIdeasAG Жыл бұрын
Bigger secondary coil with this circuit Click to watch kzread.info/dash/bejne/mH2Lw7uaYZSnqJs.html
@kalpana83954 ай бұрын
Pipe cauda ho ya Kam chauda fark to nhi hai
@harshitrana3712 Жыл бұрын
Can I use this coil to glow a 18W CFL bulb ?
@milespeterson5049
Жыл бұрын
Yes absolutely! you can also use it to light up neon blubs wirelessly!
@Greenorange0 Жыл бұрын
If you got your.mosfet bursted you should do not gave ground with the heat sink
@pri5469 Жыл бұрын
What will happen, if I increase and decrease the number of coil turns..?? Instead of 600 to either increase or decrease the coil turns
@guru6322
11 ай бұрын
Increasing turn increases output voltage and vise versa
@the_royalgamer484Ай бұрын
Can something else be used in place of the magnet wire? Because magnet wire is not available in my city
@TechIdeasAG
Ай бұрын
It’s must
@the_royalgamer484
Ай бұрын
@@TechIdeasAG can we use copper wire instead of magnet wire
@combycat
26 күн бұрын
@@the_royalgamer484if it has insulation you can. Plain copper wire doesn’t have insulation so yeah you need wire with insulation.
@abhijayjayan6326 Жыл бұрын
Drain pin dimensions pls??
@easydiyelectronics10582 жыл бұрын
Hi can I use any copper wire
@Jasmarkelina2 жыл бұрын
It "hertz"!
@i.m.qislamicworld8948 Жыл бұрын
I need same tosla coil how much money need
@short-directory3 жыл бұрын
NICE.
@ohmbairava13093 жыл бұрын
Super.... what's its use
@musicalrainbow5438
3 жыл бұрын
it is not wireless power of current it is of voltage because a tesla coil creates high voltage
@chunloonglow59052 жыл бұрын
Hi Sir, i've made 1 following your video, but my capacitor burst easily (already burst 3 capacitors so far) by it own, any advise? my setup & components almost copying your video, except i am using IRF540, and i do not attach a fan at my heat sink.
@TechIdeasAG
2 жыл бұрын
Use capacitor with higher voltage rating
@chunloonglow5905
2 жыл бұрын
@@TechIdeasAG thanks for your prompt response. any other methods like connecting the capacitor in series/parallel way? cause i noticed the capacitor is very hot during operating. (seems working well on 9V, but capacitor easily burst on 12V)
@dunderdee
2 жыл бұрын
polarity check
@issacpuppala7889
2 жыл бұрын
Use filim pf capacitor with 2000v 4.7uf rating it works just fine
@shanecarlson5718
Жыл бұрын
In series no polar ceramic hv caps add values
@mrrdom57162 жыл бұрын
How to coil mm?
@musicalguys29326 ай бұрын
What's the role of heatsink and fan?
@ElPsyCongroo.
6 ай бұрын
Dissipating heat lol
@kalpana83954 ай бұрын
I have 6.5 uf 500v and 3.9uf 500 v which one is better
@TechIdeasAG
4 ай бұрын
First try with 3.9uf
@innovative_ideas3 жыл бұрын
Best😍
@v.madhukumar67252 жыл бұрын
What is the gaudeget name you have Used to increase the power
@amutha1652
Жыл бұрын
Potentiometer
@nelsonet7216 Жыл бұрын
What gauge is the magnet wire?
@guruxgamingoffical8925
Жыл бұрын
36 number
@xhacker7732 Жыл бұрын
Is this working
@jaiminbhoya2764 Жыл бұрын
sir when touch on plazma spark then your Jaad is burning
@indianhackersushanth89408 ай бұрын
can we ues irf540n
@oasisanimus53492 жыл бұрын
hey can i use 0.1 mm copper wire please reply fast
Пікірлер: 251
I like the way u secured the pvc bobbin with 2pcs of half moon plastic. Nice!!!
@TechIdeasAG
2 жыл бұрын
Thank you
When most people think of a Tesla coil, they imagine a large, imposing object with sparks flying everywhere. However, it is possible to make a tiny Tesla coil that is just a few inches tall. This coil can be powered by a small battery and can produce millions of volts. The key to making a tiny Tesla coil is to use a high-voltage capacitor. This capacitor will store the energy that is produced by the battery and release it in short bursts. The secondary coil of the Tesla coil should have a very large number of turns, as this will increase the voltage output. The final step is to create an ignition system. This system will create an arc between the two coils and will generate the sparks that everyone loves to see. By following these simple steps, you can create your own tiny Tesla coil that packs a powerful punch. Theoretically yes!
@harms123
Жыл бұрын
You're not gonna be making million-volt arcs with batteries.
@milespeterson5049
Жыл бұрын
I need help my tesla coil is not working! I smell burning!
@harms123
Жыл бұрын
Sure if you have some massive fuckoff lipo you can but that's about the only exception
@ankanpradhan9724
Жыл бұрын
But more the no. of turns in the secondary coil the mosfet will get hotter and hotter (not sexy hot). So I suggest to use a high power mosfet like irfp260n or, even better irfp460n
@harms123
Жыл бұрын
@@ankanpradhan9724 wot?
That is a high current draw even at 9v. Is it the current or voltage that controls the output? I was always wondering how to properly bias a mosfet in a slayer circuit so thanks for that one.
at what frequency does it resonate?
Thank you for this video 👍 It's a very good idea 😉
Hello friend, can you tell me what voltage and amperage you used? Grateful!
Can we use thicker Cu wire for it?
how do you make the electricity above become quite large?
Amazing video😮😮
I have B100K potentiometer can I use that instead of the 1k ohm?
Work better with IRF540 MOSFET because it has a higher switching frequency
@hpvide
2 жыл бұрын
Can I use 44
@hungdpiqn
Жыл бұрын
do you know every coil have they own resonance frequency
@harms123
Жыл бұрын
It also has a higher on resistance, which means you generate more heat. You don't need fast switching if the resonance frequency of the secondary is low enough.
@milespeterson5049
Жыл бұрын
Oh interesting. I was going to order the one in the video but are you sure it will work with IRF540? did you test it out for yourself?
@rupeshpatil5568
Жыл бұрын
@@milespeterson5049 Yeah my setup still works perfectly fine.
Can we use more wide copper wire
Buddy what is the cost of all these ?
What toroid did you use
can we use 12v power and 2amp?
I have also tried to make one but I would suggest that to use IRFP260N mosfet with 24v power supply
@b-beluga4510
Жыл бұрын
I ve used irfz44n and it works fine. Can i use 24 volt with this system?
@OmletArcadeOfficial
4 ай бұрын
@@b-beluga4510Yes you can use it because it works good for me
@sree137918
2 ай бұрын
@@b-beluga4510your mosfet will probably die with this circuit at 24v because of excessive heat created by it.
Amazing
does this burn?
Wow amazing bro
Does a 1000uf capacitor work?
Superb
Except 47ohm resistor which resistor we have to use to get spark
Can it be powered with 12v 2amp
Please reply.. working on this today.. still 5 am i am awake with this
Awesome man I will try it ....👍👍👍 I love your trick of winding the coil really awesome Idea. Keep it up 😉
It's great.
увеличь количество витков вторички до трёх, проводом хотя бы 2,5мм!!! и увидишь что произойдёт!!!
Nice
Great I have a few IRF540 and I was thinking if I could make a slayer with those since 2n2222 are too weak , thanks for this tutorial
@aplacetoimproveteslacoilin3721
Жыл бұрын
Replacing the spark gap with transistors IRF540 and 2n2222 makes Tesla coil smaller, more efficient and easier to build. The transistor acts as a switch to turn the current on and off in the primary coil. This just resonant nature of Tesla coil creates high voltage and frequency which is used to create sparks.
@harms123
Жыл бұрын
@@aplacetoimproveteslacoilin3721 Okay? That's not what he asked?
How did you make that power suply
Can we use it with 10k pointometer
What is the Golden wire after 47 ohm
What would happend if i keep turning the potentiometer
أحسنت لقد أذهلتني
What about using 5 or 6 turns of 1.5 or 2mm wire for the primary coil. Also, maybe using a larger capacitor, or 2 or 3 in series.
POV: you thought this was a small easy diy project
@gaynzz6841
3 күн бұрын
you can make it small and easy. all you need is to wind a coil, and 4 components. the amount of complexity is the designer's choice.
What source did you use is it dirext or alternate current ?
@PlasmaPro8
Жыл бұрын
Dc
wow! Great,
Can I use another potentiometer
Impressive
Does it work?
Please show the circuit diagram without potentiometer
Hello will it work with a 9v battery small one
6:40 what is that thing powering the tesla coil?
well done my friend !!!
What music did you use 🤔
What is the gauge of drain pin
It's works bro.thank you for the tutorial!
@prashantpatel8290
Жыл бұрын
Hi what gauge did you use? I am not getting 0.07mm wire anywhere
@amutha1652
Жыл бұрын
@@prashantpatel8290 I used 38 awg magnet wire
@prashantpatel8290
Жыл бұрын
And all other parts remained same? What Mosphet you used? Is the spark good size and powerful?
@amutha1652
Жыл бұрын
It's a bit small
@amutha1652
Жыл бұрын
The same mosfet
Untuk membeli kawat lilitan x ini dimana ya...?
Sir, 1k potentiometer replace 100k potentiometer use kar sakta ha
can it glow cfl blub or tube
Can 500v 4.7 capacitor work
50k protect and 250v 47uf capacitor messed up? Replay me..
Can i use 10 k potentuometer
Does anyone think that a electrolytic capacitor might blow up easily? I do not feel confident buying a $10 capacitor and it blows up. So should I get a film capacitor instead?
@adityasudershan9629
Жыл бұрын
Yes electrolytic capacitors can't handle that High frequency so using a film capacitor is better!
what is the thickness of the copper wire you used in coil
@JonathanGameHD
8 ай бұрын
0:28 0.07 mm diameter
I want to try this
I need 0.07mm wire please kidher se mangvana hai vo bataiye
Is it burning or not
Really good to hear
Bro ,we can use C.P.U cooler in place of heat sink with fan ?.
@TechIdeasAG
2 ай бұрын
Yes, it will also work
It's very good 👍 👌.
Very interesting 👍👍👍
@TechIdeasAG
4 күн бұрын
Thank you! Cheers!
Should this magnet coil is need to be insulated or not?
@erikzidan2601
3 ай бұрын
Its just copper with isolation, and of course you need it otherwise you would short the secondary
Not working.. please help me.. capacitor is not even charging.. what should i do?
Help! I don't have that weird capacitor. I have a 3.3uf one but it's rated 50v. can you help? will it still work? please respond.
@milespeterson5049
Жыл бұрын
@Smaxi botYeah I will just order a 450v capacitor. on the internet along with the IRFz44n Transistor.
@mike289homebuilt5
Жыл бұрын
Miles. One I built/ Ludic Science/ Triple Primary Slayer Exciter . I only used one transistor and Two medium Led (backwards) as substitute for diodes. Any of these slayers substitute 1/2 watt potentiometer for the Resistor that way you can turn the power up mount a Cfl on top of the secondary pop bottle plastic. The Mosfet circuit one is better but they both work.
Help, my tesla coil is not working again. I got the same transistor the resistors and even the same capacitor, but every time I fire up the circuit I get no output from the tesla coil, and If I turn the potentiometer, I start smelling a burring smell, no smoke but not good for my components. why is it doing this? and how to fix it? Please comment below. 😃👇👇
@adityasudershan9629
Жыл бұрын
Flip the connections of primary
@milespeterson5049
Жыл бұрын
@@adityasudershan9629 I did try that and I still smell burning. what am I doing wrong? its at 12v so it can't be voltage its 1 amp so that's fine. what's the problem is it wired wrong maybe?
Can we glow CFL bulb
What is the gauge of primary coil? Please reply as I need it very much
@guru6322
11 ай бұрын
I made one with 32 guage works fine but if you want high voltage output then go for 20 - 30 guage wire. But remember thinner the wire gets chances or wire burning increases.
Hi sir what is the name of the device that you use when you're measuring sizes
@abhijayjayan6326
Жыл бұрын
Vernier calliper
Kiểu này mình thấy tia ok hơn kiểu kia😄
Me I used 0.4mm of magnet wire, and I need a mosfet or transistor that can be input of 12v dc.
Wow, will the coil warm ?
@TechIdeasAG
Ай бұрын
Nope,
Bigger secondary coil with this circuit Click to watch kzread.info/dash/bejne/mH2Lw7uaYZSnqJs.html
Pipe cauda ho ya Kam chauda fark to nhi hai
Can I use this coil to glow a 18W CFL bulb ?
@milespeterson5049
Жыл бұрын
Yes absolutely! you can also use it to light up neon blubs wirelessly!
If you got your.mosfet bursted you should do not gave ground with the heat sink
What will happen, if I increase and decrease the number of coil turns..?? Instead of 600 to either increase or decrease the coil turns
@guru6322
11 ай бұрын
Increasing turn increases output voltage and vise versa
Can something else be used in place of the magnet wire? Because magnet wire is not available in my city
@TechIdeasAG
Ай бұрын
It’s must
@the_royalgamer484
Ай бұрын
@@TechIdeasAG can we use copper wire instead of magnet wire
@combycat
26 күн бұрын
@@the_royalgamer484if it has insulation you can. Plain copper wire doesn’t have insulation so yeah you need wire with insulation.
Drain pin dimensions pls??
Hi can I use any copper wire
It "hertz"!
I need same tosla coil how much money need
NICE.
Super.... what's its use
@musicalrainbow5438
3 жыл бұрын
it is not wireless power of current it is of voltage because a tesla coil creates high voltage
Hi Sir, i've made 1 following your video, but my capacitor burst easily (already burst 3 capacitors so far) by it own, any advise? my setup & components almost copying your video, except i am using IRF540, and i do not attach a fan at my heat sink.
@TechIdeasAG
2 жыл бұрын
Use capacitor with higher voltage rating
@chunloonglow5905
2 жыл бұрын
@@TechIdeasAG thanks for your prompt response. any other methods like connecting the capacitor in series/parallel way? cause i noticed the capacitor is very hot during operating. (seems working well on 9V, but capacitor easily burst on 12V)
@dunderdee
2 жыл бұрын
polarity check
@issacpuppala7889
2 жыл бұрын
Use filim pf capacitor with 2000v 4.7uf rating it works just fine
@shanecarlson5718
Жыл бұрын
In series no polar ceramic hv caps add values
How to coil mm?
What's the role of heatsink and fan?
@ElPsyCongroo.
6 ай бұрын
Dissipating heat lol
I have 6.5 uf 500v and 3.9uf 500 v which one is better
@TechIdeasAG
4 ай бұрын
First try with 3.9uf
Best😍
What is the gaudeget name you have Used to increase the power
@amutha1652
Жыл бұрын
Potentiometer
What gauge is the magnet wire?
@guruxgamingoffical8925
Жыл бұрын
36 number
Is this working
sir when touch on plazma spark then your Jaad is burning
can we ues irf540n
hey can i use 0.1 mm copper wire please reply fast
@TechIdeasAG
2 жыл бұрын
Yes, you can use
@oasisanimus5349
2 жыл бұрын
@@TechIdeasAG thx man
Hey 12V Ac or DC?
@TechIdeasAG
Жыл бұрын
Dc
Give parts name in description pleause 🙏
Can I use a IRF530 MOSFET?
@explosivesMan
Жыл бұрын
No will expolde
Luar biasa