PVC companies will always smile when they see you coming.

133 V x 0,3 A = 40 W x 24 h = 960 Wh . Nice ! :) Bravo ! :)

very professional! :) It looks like you have found the perfect river to test these in.

Encase it in a pipe for more efficiency?

use the alternator from a car and run everything on 12 volts, lights, Radios, fridges TVs all run on 12 volts now, it is the standard voltage for outdoor equipment and all caravans and boats run 12-volt systems, It is also easy to store the power you are producing as all leisure batteries are 12 volts,

Thanks for the details. You videos have tremendous improvement every time!!

How much loss from those loose chains I wonder...

@1danny2k

4 ай бұрын

Tight chains would have added friction

COOL.CLEAN ENERGY.

This is so cool, if you improved this a bit, closed up some of the water spillage over the sides and then hooked it up to a battery, you'd be generating roughly 1kWh of electricity a day. The even cooler part is the river keeps going so could could set up a few of these down the river and you could easily generate enough electricity to power your house

@davidcastano7541

7 ай бұрын

what type of battery would you use though

@davidjosh5640

Ай бұрын

Could use similar storage batteries used for off grid type spots with solar?

Very professional work, Thanks my friend, Big like ♥️♥️♥️♥️♥️

I wonder how a undershot waterwheel would perform in this stream. Would probably work better and easier to design and make than the archimedes screw. I do admire your craftmanship.

@mr.construction9846

Жыл бұрын

Thank you. maybe we should try it

@davewarrender2056

Жыл бұрын

My I add something, wat about mounting the water wheel horizontal In The water flow , would that eliminate the under/over shot need. Also make it out of c/fibre , put a large drive wheel on the drive shaft , connect to a significantly smaller drive wheel connected to vertically mounted generator

@karaabdelkader1273

8 ай бұрын

@@davewarrender2056 you mean like using gears to increase the motor input shaft speed? Will it produces more power?

@davewarrender2056

8 ай бұрын

@karaabdelkader1273 horizontal or vertical doesn't matter. If you place a small gear on the output shaft and transfer the that power via belt/chain to a larger gear , you will get slower revs , but more torque. Which for things like driving water pumps , flour Mills is best. But for electrical generation you need I believe large gear on output , small gear on drive shaft. I think it's large gear to small, high revs , low torque. Small gear yo big gear , low revs high torque

@karaabdelkader1273

8 ай бұрын

@@davewarrender2056 I really appreciate it, you really had no idea how much I needed this

The larger the gear coming out of the turbine, the faster it will spin the generator.

Bravo, complimenti dall'Italia! 0,3 amp. con 130 volt, giusto? fanno 39 watt. e non sono così pochi! Chiaro che il ventilatore che hai provato è potente e la frena. Ma se la tua turbina a vite d'archimede la utilizzi con motore trifase in bassa tensione, un brushless a 12 o 24volt, accoppiandola a un regolatore di carica, una batteria e un inverter hai creato un perfetto micro impianto, in grado di fare funzionare perfettamente luci e piccoli elettrodomestici di casa. Se la costruisci con tre principi, tre eliche, migliori l'efficienza. Complimenti ancora!👍

Great! And hilariously retro. It alone could save at least 1/2 the Whurld! Cuz only 1/2 of it is in the Water. Harhar

Great video sharing

@mr.construction9846

Жыл бұрын

Thank you

Steel chain in the water... What can go wrong?

very nice work lovely made

@mr.construction9846

Жыл бұрын

Thanks 🌹🌹🌹

Great Job 👏 ✅ But I wonder why you don’t use a bigger gear on the main shaft in order to multiply revolutions even more !

@mr.construction9846

Жыл бұрын

I've also had some videos with a system with a higher gear ratio, but it probably won't work if it's too big

@karaabdelkader1273

8 ай бұрын

@@mr.construction9846 if we use gears to increase the motor's input shaft rpm, will that means more watts?

@HobkinBoi

6 ай бұрын

Gearing something for high revolutions reduces your torque. Easily shown in the video where connecting a fan nearly completely stalls the turbine.

Hi there, honestly lovely work! Was hoping to ask if you could lead me into the right direction when it comes to choosing the design parameters of the turbine, like revs, blade twist angle and so on. Best regards

My guess would be that it will work better in a full pipe instead of the half pipe, so pressure could buildup. Also being vertical should help.

@mr.construction9846

8 ай бұрын

probably so

@krslavin

Ай бұрын

The advantage of the half-pipe is that it self-clears debris much more than a full pipe which would need an (admittedly coarse) mesh filter, which tends to clog up.

Cool.!

Làm tua bin gió đc không bạn?

what are the sizes or models of those sprockets??

Можно сделать передачу со шнека сразу на вентилятор😄

Can that spiral propeller can also be used as a silent propulsion for motor boats?

Ganti pakai kipas yg gede ya bos

Good invent, but.... You may think a solution to prevent the chain get rusty... Especially the one that soaked in water.

@alexnicolinirealtor9463

Жыл бұрын

I think 🤔 the main gear with the chain should go longer to the point it’s going to be over the water label and also utilize a bigger gear on the main shaft , but other than that it’s an amazing job done ✅ men 👏👏👏👏

What is the gear ratio for this?

Can you tell the dimensions please😊, because i need to make a prototype for archimedes screw turbine for my school project

Hay quá

@mr.construction9846

Жыл бұрын

Cảm ơn bạn

It would be better in reverse as a grain auger to lift grain

Hi is that an unwinded AC Motor?

Thanks, sangat bermanfaat sekali.. Tetapi saya memeliki beberapa pertanyaan: 1. Apakah bearing di tenggelamkan di dalam air akan merusak bearing? Dalam jangka panjang pelumas di dalamnya akan hilang oleh air 2. Adakah bearing yang tahan air? Thaks.. Good

@nzs316

Жыл бұрын

A grease box like a propeller shaft on boat would solve that.

@ayonchannel4825

Жыл бұрын

@@nzs316 oke tks a lot

👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻

@mr.construction9846

Жыл бұрын

👍👍👍🌹🌹🌹

Can you tell me what the diameter is from the screw? And couldn't you run a bigger dynamo on it?

Если бы была возможность сделать это всё идеально, стык в стык и из нужных материалов, чтобы усилить давление на шнек, то думаю, можно было бы вырабатывать ещё большее напряжение👍

@mr.construction9846

Жыл бұрын

В яблочко

So, the voltage is fine but how many watts are you getting?

@rivaldy8151

Ай бұрын

Power = volt × ampere

what is it called the thing inside the bearing to lock the rod to the bearing???? 3:18

@huwbishop6995

9 ай бұрын

It's called a saddle bearing or pillow block. The bearing is connected to the shaft via grub screws.

Can I replace the iron frame to be wood or no ??

@mr.construction9846

Жыл бұрын

As long as it's sturdy enough, of course

@khaledsalah1921

Жыл бұрын

Please, what is the area of the entrance of the frame to determine the velocity of water??

@khaledsalah1921

Жыл бұрын

Is any generator can used in Archimedes turbine ??

can i use 220 v ac motor?

@mr.construction9846

8 ай бұрын

Maybe we can use DC through the booster

Sir how many volt DC motor have you used?????

@mr.construction9846

Жыл бұрын

It is the motor of the air conditioner 110v 52w

What is it made from ?

@mr.construction9846

Жыл бұрын

The screw is made of pvc, the motor is the motor of the air conditioner

0:36 dùng cái gì để cắt vậy

@gregglesthemaker1024

10 ай бұрын

Probably the same angle grinder

dc motor 24V 250w 2750 rpm,this motor and the motor use using is similar?

It seems I will visit in hardware store to buy stuff for new project...

@mr.construction9846

Жыл бұрын

👍👍👍👍

izin bertanya,gear yg dipkai itu namanya gear apa?

@mr.construction9846

11 ай бұрын

Ini adalah motor AC yang bisa Anda lihat di sini : bit.ly/3lfjnW7

感谢先生，这套系统装到小型船上比较好，自我循环充电推马达，船棚上在安装一套太阳能系统。船跑起来带动的风安一套风力发电系统。这是永动机船哪😃

Me interesa para mí finca

@mr.construction9846

Жыл бұрын

It will be proportional to what you get

Hola todo está bien sólo preguntó de donde sale el agua?desde Argentina saludos

@mr.construction9846

Жыл бұрын

Esta pregunta es bastante difícil, es un problema de todos.

La turbina ni siquiera gira...

@gregglesthemaker1024

10 ай бұрын

When in the video is that? He pauses it at one point to make it easier to see the multi meter

4:50 😂😂😚😚👨‍🏭👩‍🏭

@mr.construction9846

Жыл бұрын

🌹🌹🌹🌹🌹🌹

The number 133w or 133kw sir

pesou....................

))) Дико тупой развод

FAKE ...FAKE.. Don't make fool your audience. Only video editing.. All fake.The water pressure is very less. It couldn't run the pulley. If run rpm is very less. How it's generate 120 v ?

@mr.construction9846

Жыл бұрын

Thank you so much for every video you watch and leave a review, even though it's not from your head

@youtubestinkt9830

Жыл бұрын

Would the water pressure increase, if you'd let the screw run through a closed pipe? Would that be a solution?

@gregglesthemaker1024

10 ай бұрын

It is probably real because I have got an couple volts from a tap before