Issues in order of appearance : - No thermal insulation - Evaporator much bigger that the condenser - Capillar seems too short - Fan working wrong: it is blocked, and in the opposite direction (should "suck" the cold air through evaporator to the can). The best would be insulating it inside a styrofoam can with some alcohol for thermal transfer between the drink can and the evaporator. - 9V battery with very limited energy. - Zipties probably do not seal efficiently the tube, it forms a bend - Using a needle instead of an access, would generate a weak point for the silicon hose. - No minimal thermal insulation, the condenser is too near the evaporator

@jdmccorful

3 ай бұрын

Wondering about non condenseables?

@mem1428

3 ай бұрын

also note that if they used a Stopcock 3-way Luer Lock they could essentially have a non destructive way to charge the system as well, without the use of a needle

@alexandrebeaudoin9191

3 ай бұрын

Ffs this isnt a 5 ton unit it's doing the job for this 😂

@LBCAndrew

3 ай бұрын

@@jdmccorfulI i'm fairly sure it wouldn't work for very long due to non condensseables. I own a 1932 GE Monitor Top refrigerator and that system while much bigger, requires bleeding off that gas while under load or it just won't cool using Methyl Formate as a refrigerant.

@joeds3775

3 ай бұрын

@@LBCAndrew ahhh yes, at what stage did the poster add the methyl formate?

So this is the new scam format is it. Instead of weird "Free energy" devices, its now using aquarium pumps, expanding butane gas and silicone hose. For example, how is a fan supposed to work when its glued directly to a piece of wood. It wont get air...

@justinoortiz8476

3 ай бұрын

He has a half inch hole drilled thru the wooden board but it looks like the board is resting on the table which would prevent airflow. Either the system does not need a fan in the first place or it is fake.

@Zeddify

3 ай бұрын

definitely fake, it ices up in SECONDS. freaking BS

@heromeryandi5973

3 ай бұрын

Reverse video with clock editing, the scammer spray pain killer (usualy use in football game when injured)

@1islam1

3 ай бұрын

​@@justinoortiz8476⚠️ God has said in the Quran: 🔵 { O mankind, worship your Lord, who created you and those before you, that you may become righteous - ( 2:21 ) 🔴 [He] who made for you the earth a bed [spread out] and the sky a ceiling and sent down from the sky, rain and brought forth thereby fruits as provision for you. So do not attribute to Allah equals while you know [that there is nothing similar to Him]. ( 2:22 ) 🔵 And if you are in doubt about what We have sent down upon Our Servant [Muhammad], then produce a surah the like thereof and call upon your witnesses other than Allah, if you should be truthful. ( 2:23 ) 🔴 But if you do not - and you will never be able to - then fear the Fire, whose fuel is men and stones, prepared for the disbelievers.( 2:24 ) 🔵 And give good tidings to those who believe and do righteous deeds that they will have gardens [in Paradise] beneath which rivers flow. Whenever they are provided with a provision of fruit therefrom, they will say, "This is what we were provided with before." And it is given to them in likeness. And they will have therein purified spouses, and they will abide therein eternally. ( 2:25 ) ⚠️ Quran

@antoniodasilvasampaio9366

3 ай бұрын

Além dos comentários acima, uma somple bateria de 9V, de baixa capacidade de corrente, jamais iria rodar o "sistema"!!

You want the fan blowing on the hot coil (condenser) to help get rid of the heat, and the cold coil (evaporator) insulated so it only absorbs heat from the can, and not the air.

@ylajodiste1

3 ай бұрын

What hot coil? That's fake, just by looking at the power supply it uses you should notice it.

@heathbecker420

3 ай бұрын

That would be true if this wasn't a fake.

@Sir_Sway

3 ай бұрын

guys this is real i made one of these last week chilling my heinekens right now!

@v1fong

3 ай бұрын

How an rv propane refrigerator works. General physics. Good suggestion, why the system froze and locked up

@DoubleMotherLess

3 ай бұрын

@@Sir_Sway And im driving my plane with beer right now, it has enougth power for my homemade engine and its so fast no1 can catch me eigther

Every refrigeration expert in the world must have gathered here together in the comments. Amazing.

@DodgyBrothersEngineering

3 ай бұрын

And every gullible fool in the world can't see the obvious fakery.

@AJG-mx6ld

3 ай бұрын

Y not because everyone knows the basic law of cooling so everyone share his opinion for this 😂

@ghoulbuster1

3 ай бұрын

All these experts, they must be rich! With bs LOL

@asandax6

3 ай бұрын

All you need as a 10 grade understanding of thermodynamics and Ideal gas laws. No need to be an expert.

@keithdelgado9336

3 ай бұрын

And nobody mentions the rooster

Reminds me school project, where we made an air cooler but it was not cooling, but when visitor came we put some ice to the tip of thermo meter and showed that it cooled for around 10 degree.

I wonder if the butane leaking from around those zip ties (they are all oriented the same way thus causing a place for leakage) is help in the cooling just because of evaporative loss.

@RedMoon-666

3 ай бұрын

OMFG This is the video edited backwards.

@user-vy3ly8pi1i

3 ай бұрын

I was surprised when no liquid electrical tape, and not even any rubber cement, was used to cover those zipties and the part where the tube is clamped onto the pipe, to ensure an an airtight seal. In fact, I'd have carefully sealed the copper inside some liquid polymer, carefully painted along the tubes, so it fully coats them, for at least a half inch diameter on either side. For the tubes, the pump, wires, coating of liquid electrical tape.In order to keep from EXPLODING THE CAN, which such rapid and severe cooling could do, I'd have a fan blowing the cooled air into one end of a container, with several tiny exit holes drilled all over the container, to let the cooled air out in every possible direction, ensuring the can is evenly and carefully cooled all over.

@bobboboff5326

3 ай бұрын

Тоже заметил. Уж лучше бы припоя напаял 😁

The use of the clock to show that the video isn't really just the copper tube thawing out after being hit with some freezing spray is an innovative touch. Rather than get hold of a clock that runs backwards you just use a few shots of it and don't show that the time is being adjusted.

7:56 that thumbs up was actually middle finger for the viewers😂

@fvrrljr

Ай бұрын

It really works! This butane gas doesn't require much pressure because it's low-pressure; at 2 bars, it already becomes liquid, and it puts the gas into liquid form inside the system, helping it function for a while. As it's a low-pressure gas, this engine can easily compress it back into liquid, thus completing the cycle.

@freddykruegericanseeyou6863

3 ай бұрын

I don’t know but seems like I got a try it but I have different math I always upgrade what others they forgot or actually my job to correct those guys he used needle if you get the IV line the one they put it in your hand in the hospital it has lotta part that you can inject the light and fillet that if there’s gas will work but I wanna try it with mini computer radiator with Freon

@MR-Nitro

3 ай бұрын

I've conducted several experiments with this gas, and it's very easy to compress. You can test it yourself by putting it in a syringe. In its liquid form with the syringe nozzle capped, you can easily compress it with your hands.@@freddykruegericanseeyou6863

@EmilyFirefly235

3 ай бұрын

Very true I am a hvac tech who has 10 years in the trade. Butane propane are very good refrigerants we do not use them because of then being flammable. In the old days they used ammonia.

@and9290

3 ай бұрын

People who fall for this are the same people who get scammed all the time throughout life, while the science principal of this is very real this person has faked the outcome. It needs a proper compressor to compress the gas back into a liquid, and probably a correct expansion valve, and he's done something fishy with the clock. Well this isn't as bad as the"Free energy", "perpetual motion" crap, he's just faked this outcome with freezer/duster can spray then reversed the video.😂😂😂

@MR-Nitro

3 ай бұрын

Go study, this gas is low pressure, it doesn't need a powerful compressor. I've worked with this type of gas before, don't compare our intelligence with your ignorance.@@and9290

This absolutely works* *Unit must be operated outside, in sub-zero temperatures only.

@bobboboff5326

3 ай бұрын

It's true 👍👋😁. In Siberia!

This really works even without the battery source! When the butane leaks to the air from the system, it will actually cool down. This is the latent heat of evaporation it absorbed, but ... it won't last long unless you keep pumping in the butane. 😂 Do you recall the butane can cools quickly when you refill your lighter? Just because some butane leaks and evaporates quickly, it absorbs heat from the surroundings. Also because of the leaking butane, the whole setup was moved outside to avoid build-up of dangerous inflammable gas! 😂

@ericdvorak7030

3 ай бұрын

As a 30 year refrigeration tech I can tell you this isn’t even close to something that would cool. Isobutane is a refrigerant (R600a) and it has a boiling point of 11*F, at just room temp it’s 50psi and the silicone hoses would have blown off. Also that is a pump, not a compressor, it’s not capable of pressurizing the gas to condense it. The fan would need to be on the condenser more than the evaporator, I could go on… So my question is, knowing that this is completely fake, why spend the time to make something so stupid and spread misinformation? Are you that starved for attention?

@cemilsafak7192

3 ай бұрын

Bravo

@user-ix9lx4sp1z

3 ай бұрын

​​​​@@ericdvorak7030Why? That should be obvious. Because you watched the video in full and commented it, so now the algorithm will push the video to more people. That's the goal of the video maker. They got paid, doesn't matter whether you like the video or not.

@ericdvorak7030

3 ай бұрын

@@user-ix9lx4sp1z I realize they get paid for clicks and comments but is it really that much? Enough to go through the effort to create this video, which, aside from being BS, is well made. I wonder if the thumbs down counters the views?

@ericdvorak7030

3 ай бұрын

If you believe this works you’re an idiot.

Congrax🎉🎉🎉🎉🎉It is the basic principle of the fridge.

The conduit from the compressor to the evaporator needs to be a lot smaller for this to function properly. 😂

I love the rooster in the background sound.

@ryanjohnson3615

Ай бұрын

Am trying to determine if you are you the guy on the right side or the left side of your profile pic.

@rasputinsorphan1260

Ай бұрын

honestly, it depends on the day @@ryanjohnson3615

Ya wrap that around your bong 😂 "its so smooth bro hit this"

@krashd

10 күн бұрын

That's why you put ice cubes in your bong. Trust me, you'll never go back once you've tried it.

Love the way of tutorial so much. No annoying ear rape kind background music, no long unnecessary explanations, no indian accent. easy to understand, cheers.

@leonelcardenas-sj9fo

3 ай бұрын

100% agree, specially for the no indian accent.👍🏼

@vermilionssj9081

3 ай бұрын

Yes but its sadly Fake

Genius!!! Mass production starting my moms basement right away ty

@mrhide7403

2 ай бұрын

Did you try it? What are you gonna produce??

@TheZombieSaints

Ай бұрын

Copium I'd say is the only thing it will produce 😂

The idea is nice. Do see some questionable aspects especially the location of the fan, but it does give the basic concept and something to work off of. It would be interesting to make several and fill it with different coolant charges and time each one and note the difference in temp/time

There's not an actual chicken in the background huh?

Excelente idea. Una pregunta. El ventilador es obligatorio para el enfriamiento, o es opcional?

ma aggiungere gas senza fare il vuoto non crea problemi??? la ventola non andrebbe sull avvolgimento di raffreddamento? qualcosa non torna...

This will be used to make my own air conditioner

If I were to try this, I would do three things differently. First, I would insulate the outside of the evaporator coil. As it's being used for contact-cooling of the soda can, why let it uselessly cool the surroundings? 🤦🏻‍♂️ Second, I would open up the condenser coil to form a circular array and put that against a vertically-mounted fan (or horizontally-mounted but with a good couple inches of intake air gap!). And third: if I want that to be battery-powered, I'd use at least three lithium batteries. That piddly little 9V battery with the six AAAA batteries inside can't supply much current. I wonder how many 9V batteries were needed to cool that can of soda? 😄😄

Awesome 👏. Funny the rooster wakes up late around 10+.

I see its a cheap fun way to do that, but what's the purpose of the fan if only have a little vent hole, the wood block from the bottom on the table and the can tight to the coil? That fan not have a purpose and only drains the battery. I think was way better if you use the fan to cool off the heating coil instead and leave the cold coil by itself with the can.

The fan should not be blowing through the evaporator cooler rather it should cool the condenser to liquify the gas . The cappillary tube should be hot not cold because the evaporated gas is being compressed

Many people saying this is fake but couldn't butane be used as a refrigerant and the expansion tube principle here work if powered and fanned correctly? It's pretty cool to be able to make a mini fridge without peltier devices.

To get the evaporator to that temperature you need a suction pressure of -50kPa or so for R600 (butane). A head pressure of 400kPa would be a reasonable enough assumption as the condenser is a bare tube, convection cooled. That little pump can’t push that sort of compression ratio, no way. The capillary tube is far too short for this to be achievable. The capillary tube frosting up suggests either the liquid butane is undergoing a pressure drop before the capillary tube. At normal atmospheric pressure butane boils at close to 0 degrees C, just a tad under. There’s more to this system, it cannot operate correctly or efficiently as built.

How many 9v batteries does it take to cook one drink ?

My lab partner made this heat pump once when is was at Caltech. The only reason we don't use this is because of the danger of flammable gas involved.

Si es fake, lo mas dificil fue hacer marchar el reloj en sentido inverso (por el video en reversa)

I've seen some explanations about the working principle of refrigerators in projects alike, but this one nailed it in terms of accuracy of Physics concept.

@krashd

10 күн бұрын

Don't let all the refrigeration "experts" in the comments hear that.

Do i understand this right? the gas releases heat in the medium coil, gets compressed in the small coil because of the small diameter turning into a liquid then expands to a gas in the large coil pulling heat from the can then goes through the pump then to the medium coil releasing the heat again completing the cycle before being compressed again in the small coil?

@andrewveres3965

3 ай бұрын

The medium coil is the expansion device

@andrewveres3965

3 ай бұрын

Basic refrigeration

@joeds3775

3 ай бұрын

its not being compressed its just being cooled, losing that heat energy allows it to liquify at low pressure.

Sooo... They put it on the board with a hole in it and fan sucking air from that hole and blowing it up to the can? :D Im pretty sure it could be done more easily if the can is put directly into the dry ice which is blowing freezing ar through the hole in the board :D

we did this back in the 80s with our 10th scale RC buggies to keep the engines cool, old tech......

@drQ11235

3 ай бұрын

xD

It will Work 💯

To be fair, using a 9V battery is not enough to run a 12V native brushless AND a brushed motor at the same time. Use a cheapo bench power supply next time, let alone a tiny wallwart, as batteries don't last long enough. :/

@krashd

10 күн бұрын

To be fair neither of these two motors need a high RPM for this to work so the 9V is sufficient.

That small tube will block with ice from the water which will condensate because he never bled the system of air

@fishyerik

3 ай бұрын

Not necessarily to point it becomes a big problem, air typically contains a few grams of water per cubic meter, and that system looks like it's a small fraction of a liter, so, somewhere around a milligram of water. So, not necessarily a big problem. Besides just forcing the refrigerant in there, with the air, and some aspects of the design, I personally found it really great build, for a youtube video.

@cosmefulanito5933

3 ай бұрын

@@fishyerik Great build a fake video? O_O

@LBCAndrew

3 ай бұрын

Correct. You'd have to bleed the air out of the system, by filling it with nitrogen first.

@user-pb5fb4zy4i

3 ай бұрын

​@fishyerik به نظر شما این کار عملی است یا کلاهبرداری؟

@cosmefulanito5933

3 ай бұрын

@@user-pb5fb4zy4i It is scam.

I'm going to try it today

@shaaansari618

29 күн бұрын

Have you tried its working or not?

why no picture of the temp of the can? why didnt you crack that can o0en so we can see the freeze effect? strange video

Actually this will work, they are now using butane in all domestic refrigerators, the capillary tube is where the cooling takes place just like in the video. Is not very safe but is a cool design.

Que legal será que dá certo com gás de spray de suvaco

Why did you solder the connections between the copper pipes instead of gluing them, if you use thin rubber pipes in the system that would not withstand such pressure?

Can we use plastic pipe with Almulium foil rapped on it, instead of copper pipe because i don't have copper pipe and it very expensive. Plz tell me

I shuddered when that battery clip was attached right next to pipe that had just been injected with liquid butane gas. Definitely don't try this at home.

The coils on the condensor should not be tight together! Terrible heat transfer. And need a few fins on them! Also, the condensor allways needs to be larger than the evaporator.

Good morning. Is this pump a vacuum or a simple water pump?

Anyway, whatever type of gas it is with a centrifugal pump with a turbine, it is impossible to create compression on the gas because the gas returns back. For this process, a reciprocating pump with a piston and a suction valve is needed, compression which does not allow the gas to return back.

To make cool u must compres the refrigerant with high pressure in compressor if u just using water pump to compress it almost imposibble to make it.

Really works

Will the amount of gas in the pipe be lost a lot?

Ponga el negocio hay unas disque neveres que según enfrían y no enfrían nada esta bueno ese proyecto suyo

Which gas are used

nice invention!👍

So basicly with similar setup can convert cooler box to a mini freezer... thanks for an idea...

Cool. Will do a airconditiojing ninja😅

i was fascinated by the idea of cold beer too and then the best thing in the world is just to simply pour your cold beer in a thermos and problem solved, you drink it in less than 4 hours its still cold

I will use same format to make mini air conditioning system running on 12v lithium battery. Thanks for demo.

@askaknorhadin97

3 ай бұрын

Update us when you finish 😅

Nope. 9V battery is about 4 watt-hours. It either went dead in 5 minutes or this is just silly. It is hard to believe that was liquid butane going into that tube. Not sure what the fan is supposed to be doing.

Голоса домашних животных на заднем плане придают особый шарм для данной самоделки.🤣 А если честно автор молодец👍

That 9volt battery is strong enough to power the fan and the pump at the same time?

@habiks

3 ай бұрын

yes, but not for long..

@davenone7312

3 ай бұрын

No! This why this is a total scam

@LBCAndrew

3 ай бұрын

It's not. Ive got a bunch of similar size fans and they wont spin up on a 9v battery.

@marilynman

2 ай бұрын

@rewFans rated 12V are normally operable between 10-12.6V, this one could be operable even lower at 9V. Even more, these fans are controlled by voltage which means they will spin very slowly.

@iosifszilagyi3118

Ай бұрын

Of course. Ten seconds or less..

how long it will last? the gas you put in

Quanto tempo a bomba pode ficar ligada ?

That fan is doing almost nothing. Hardly even able to create static pressure. It just can't do much with how you mounted it. It's a PC fan, not a centrifugal or turbine motor. Simplest fix would be to use a blower fan, so you have an angle to work with. This is the one single thing I'd fix about this. Everything else is fantastic at this scale. Great design.

Good inv

ja fez o prejeto para coca cola ,estou aguardando o projeto para gelar cerveja ,estou ansioso !!!!

Nothing is miraculous for those who knows. We often see what we want instead of what it really is :)

What if we don't use the circulating pump, and just add butane into the copper coil?

I can confirm this is a real refrigeration cycle that this person is using but, I’m not too sure of is how that Little pump he’s using as the compressor able to generate enough pressure to make the refrigeration cycle work but I do know is that frost you’re seeing is telling you the refrigeration cycle is working the style refrigeration system he has built is a capillary style refrigeration system. It’s one of the simplest refrigeration cycles ever and frost is normal even in Your refrigerator in your house It’s just you don’t see the frost because there’s a such thing called a defrost timer that shuts the Compressor off in the fridge for a few minutes And turns on a small heating element that is on the evaporator to melt the frost. It does it once a day usually in most fridges.

@nguyenhai7853

3 ай бұрын

Bạn đã thực nghiệm chưa, nhiêu người cho rằng video lừa rối.

@LBCAndrew

3 ай бұрын

I'm fairly sure that air pump wouldn't compress much if any at all

Que produto spray é esse que você usou?

You know there is a chemical pack that will do this, they use them in hospitals to apply to areas to relieve pain .

Ok, I read all the comments. Some I liked but the nay-sayers need to prove their opinion. This should work. The fan is not really necessary but it helps focus the cold. You conceivably use ammonia in a system like this but it would need higher compression. This would be an excellent or adequate system to build a mini-fridge or an AC unit for a Teardrop trailer. Improvements I would recommend: Pumps mounted directly to a solid surface create vibration. Vibration equals noise. Use foam rubber insulation or car door gasket material to act like a sound buffer to reduce the sound. Though this build was for a demonstration I would make a plastic enclosure for it lined inside with thin soft foam sheeting. This should also help reduce sound. A speed controller for the pump is a nice touch as would an on/off switch. And go ahead and add an on LED light. Add a power jack so you can use different power sources like a cigarette lighter, a small power supply or battery pack - all 12v DC. I hope this helps stir imaginations. I’m going to build one.

@madmatt2024

3 ай бұрын

The pump being used is designed for liquids, not gasses. It can't generate 1PSI moving a gas, let along the 100+ PSI required for a refrigeration loop (using butane (R600) as the refrigerant) to function. Even if it could generate that kind of pressure, it would would blow out the silicone tubing and you would need a fan on the condenser coil too, not just the evaporator coil. The only way something like this could possibly cool a can of soda is if you instead filled the tubing with glycol and put one of the coils in a bucket of ice water. Even then, your just using the ice to remotely cool the can.

onde acha e como chama esta bombe de gas ali ?

I lost confidence in this video the moment the 9v battery connector was attached.

Ye project sahi hai aur kaam bhi karta hai lekin is project ka gas ketne din chalega har taraf sild hai par motar ke taraf se nikal Sakta hai

@sharvilsharvil508

3 ай бұрын

Kya yah project sach mein kam Karta hai? aapne try Kiya?

@tayeemhaque8097

3 ай бұрын

Bro it's the basics of an AC or refrigerators principles so it has to work...But use a different coolant or temperature transferring liquids/ gas...

Muito interessante. Pelo que percebi ele está usando o enrolamento de cano de 3/8" de polegadas para fazer a vez do evaporador e para o condensador está usando o cano de 1/4" de polegadas. Interessante que para fazer a vez do capilar eu creio que ele esteja usando um pequeno enrolamento com o caninho de 3/16" de polegadas para comprimir o gás e expandir no evaporador. Ficou muito bom e deve funcionar muito bem sim.

@adailjosefernandesdasilva7633

3 ай бұрын

Bom dia , vc vê realmente condições de isso funcionar ? Tem vários colegas dizendo que os canos foram antes a um freezer , depois ele bota fora pra gravar o video e roda ao contrário ou seja , os canos na verdade estariam descongelado mas a gente ta assistindo reverso ... Estou desconfiando poderia me ajudar a entender ?

@klebercerqueira677

3 ай бұрын

Fake ! Aquela bombinha de água não tem potência para comprimir o gás. Note que o motor é de 12V que vai ligado a uma bateria de 9V. Pura jogada de vídeo para ter visualizações.

@hisrp4blo508

3 ай бұрын

​@@klebercerqueira677quanto a bombinha esse modelo presurizado de 36w bombeia agua e ar e pode elevar agua a 3 metros e sugar a 2 metros e muito usada em pulverizadores pela pressao que ela tem, entao quanto a bombinha ta tudo certo eu tenho duvida quanto a parte do gas

@hisrp4blo508

3 ай бұрын

Aparentemente tem fundamento acredito que se usasse um daqueles mini compressores de ar eletricos portáteis de encher pneu teria um resultado bem satisfatorio

i want to know how the heat dissipates from the machine back into the air

@johnnybenoit841

3 ай бұрын

It doesn't use heat it's the butane flowing through copper coils

When do you purge the system???

I made this using this example but the gas pressure keeps rendering the system workless. I used 12v dc battery, 12v aquarium pump, 12 v fan. This system works but the stuff doesn't seem to be working. Where am I getting it wrong?

@patritter4451

Ай бұрын

Lots of reasons this wouldn’t work but main one is that pump he’s calling a compressor. It is not even close to what is needed to make a refrigeration system work. 0:22

For this origamy to work effectively you'd better superglue your wires instead of soldering. (sarcasm)

Yolg'on ekan bu ma'lumotlar

at 8:00 it sounds like the motor is about to crap out.

How much time back up to uplode vdo

my boy's never clamped a hose with zip ties in his life and it shows. Also he got this idea from a video that came out like a week ago where one of the top comments was to use it to cool soda/beer.

@user-hr8pz6lh5w

3 ай бұрын

Disappointed

does he operate a 12V pump and a 12V fan with a 9V battery

Que tipo motor comptessor ele usa?

@giovannicesaramorim9adigan961

3 ай бұрын

mini bomba do aliexpress. nem tenta fazer, o design é todo falho e a bomba não aguenta

What are materials use?

Great idea, now go 1step bigger make a small refrigerator to hold a 6 or 8 pack Maybe use a styrofoam ice chest a power supply battery and ac Then it would be a Smash hit

ที่นี้ถี่ร้อน ถี่เย็น😊

You just need an on/off switch, to complete the design. Great job!

you used 5 zip ties instead of flaring the end and using a pressure rated clamp? WHY?? why the laziness?

the fan should blow on the condenser, not the evaporator

I think this guy has chickens

Is it permissible for me to put gas that is used in a lighter?

Is that a diaphragm pump your using?

@midixiewrecked7011

3 ай бұрын

It's your dads penis pump.😅

@askaknorhadin97

3 ай бұрын

Yes

I think in this way it is possible to make a miniature air conditioner using micro or nano technology on mobile phone devices. This idea will help in cooling the processor and battery in the mobile device, especially when playing games with high graphics, but this idea will consume a lot of energy.

@RoboArc

3 ай бұрын

The issue is energy capacity of your cellphones battery. They do use a form of this technology inside the copper of heat pipes in opines. It's like alcohol or something under pressure in a coper tube with a coper rope inside. This allows heat to move around and rhe alcohol will condense back to liquid when it touches a cooler area. I'm not sure you could put a compressor in a phone without thay fkn humming 😂

@highloughsdrifter1629

3 ай бұрын

A Peltier (spelling?) effect cooler might be more suitable for the application.

nahh, the first problem is u dont have enough hole under the fan😂

I didn't think that is a aquarium pump. Looks like a Water Pick pump. You know those mouth washing devices. Those pumps are pretty powerful in creating high pressure. My concern is the 9 volt battery, those pumps require 12 volt. I will give it a try someday.

@snaplash

3 ай бұрын

I salvaged a pump from an old blood pressure device, which looks similar, and might work as well.

It’s not it’s basically the same principle of a heat pump.

Sir desktop processor fast cooling fan please sir 🙏🏻🙏🏻