Damn dude. Great video, great editing. That chambering technique is super cool.

Absolutely cool. great video!

Fabulous job and outcome!

Looks phenomenal , really good job mate.

Great video loved it

Sick, great video John.

Great tips and idea for a newbie.. thanks John

Thank you, god bless you for making this video. I love how you explained the process in the beginning. Very helpfull

Stunning board mate

Top notch Board!

Well done! Cheers!

Awesome Vid!

great work

.....by the way John, the shape is fantastic. Very well done.

I am building one of these. I just picked up my wood. I'll be making a video of it so you can see what I've done as well. I tried building a wooden board the other way with limited success. I believe this way is one of the best. I don't know why more people don't build boards this way out of different materials.

GREAT VIDEO !

Wow I love how you screwd it together. Great idea. The one I made a few years back I glued and cut it apart to chamber but had to allow the saw kerf to in the overall width so once it was cut it would be back at my dimensions. This was a huge hassle. I've been thinking of making another so thanks for the video got me inspired

Amazing

Parabéns, excelente trabalho!

Ahh that's awesome thanks for the help bro. Sick vid as well.

Gotta admit, that was a great video, and very informative on building and shaping a "wood chambered surfboard" that has got me jonsing for a bit of crafting myself.........!

@DeepCreekTV

8 жыл бұрын

thanks Erin....get jonsing !

awesome mate

Great vid

Very nice, my next board project will be a chambered board.

bloody art

so awesome!👍✌ I shape my own boards and build wooden kyacks but this is a little above my skill, man I want one! 👍✌🌞🌻

The best I seen

Fantastic video mate...and thank you for taking the time to answer everyone's questions.

Beautiful board. Thought it was going to be a twin with keels. But I can dig the quad. Yew!

@DeepCreekTV

9 жыл бұрын

jdm31181 funny u should say, the fins on this board morphed into rear keels with tiny side bites.

Just to keep everyone interested up to date, last Jan 14 I trashed the "Bogong". I took off late behind the rocks at Schnapper Rocks GC on a 6' dredger & drove her into the bottom, agghhh...the results were 2 major splits length wise down the board, (imagine an axe splitting a piece of wood), she filled up with water an nearly sank, but the buoyancy of the timber kept her afloat, not sure if i'll repair, easier to make a new 1 i think & hang the "Bogong" on the wall. Needless to say I am missing it, it went soooo good.

@DeepCreekTV

10 жыл бұрын

well I repaired the "bogong" and she's back in the water....I had too, she's a magic carpet & they don't come round often.

@joeypennell7648

9 жыл бұрын

DeepCreekTV i found your video very useful in building my own board. would love to see another video. keep up the great work man.

no mate Not an overload of info, appreciate it. There is a mob near me on the Mornington Peninsula, they are associated with Grain timber surfboards from the US..... Classes are very expensive, I've got the plans and rocker shapes, will have a crack myself.. If they bugger up, back to the shed...lol

So good thanks!

this is so sick

Good job

Belo trabalho!... :)

nice one!!

very nice.

nearly finished the board I started last winter, what a great project and has got me keen to do another out of some better wood. Would love to see a video of you actually shaping as all I could find was foam boards being done. I know same principles but the amount of time to do each step was greater. Cheers for the inspiration.

@DeepCreekTV

7 жыл бұрын

as you can appreciate making a board while also producing a video solo at the same time is massive amounts of work....maybe some time in the future.

ripper board John true craftsmen

hey !! so nice video , Im going show guys from brazil

Bem legal👏👏👏

Ok thank you i will try ! stay in touch greetings

Thanks a million, mate! I just finished my first chambered surfboard. Thank you for putting up this video. I followed it step by step without stealing your "secrets" and my board came out beautiful and surfs like a dream!

@DeepCreekTV

5 жыл бұрын

Cheers Jason, happy to help ☺

@electricskateboardhub8126

2 жыл бұрын

@@DeepCreekTV which wood glue do you use, would love to know!

@DeepCreekTV

2 жыл бұрын

@@electricskateboardhub8126 I mainly use polyurethane foaming glue and Epoxy putty for nose/tail tips, fin boxes and plugs.

man. your videos are awesome. seriously informative and entertaining. really creative ideas man! (video content and video making!)

@DeepCreekTV

8 жыл бұрын

+Pepe Kedor Thanks Pepe.

Thanks!

Hay que revelar los secretos dear!!!😉 Para poner en práctica su experiencia

Solid

F**king brilliant! One of the sexiest boards ive ever seen.

that board looks great, I'd hang it in my wall to nice to use, Ha!!!!!

Thanks :)

continue and make more videos!

Shane, Polyester or epoxy clear filler, though epoxy bonds better than poly. Just brush it on just like paint, 2 coats, with epoxy do a second coat when first is tacky, this saves sanding between coats. Wet & dry sand then polish, personally I like the Oil finish, J.

Ok.thank you

Hey John great video mate, its Matt B from up the road. Couldnt believe when your face popped up haha been thinkking about making my own, might have to come have a look one day

@DeepCreekTV

8 жыл бұрын

+SLUSHPIT PRODUCTIONS no excuses Matt, get to it. ur welcome to drop in.

Great video! I'm planning on building one similar myself in the future. I was just wondering, did you contour the bottom of the board? Like shape concaves or a vee in? cheers

Great video. Really inspired me to have a go myself .Dont know weather I could get hold of such an exotic wood in South Wales.will have to explore alternatives.Any suggestions ?

@DeepCreekTV

7 жыл бұрын

Thanks....I'm not too sure, you need something light with a tight grain, what do they use for boat building , could be a good place to start.

Thanks for this video, I am just starting to build my blank now. Did you use polyurethane glue to assemble the chambered pieces or epoxy? I'm making a build video series as I make it, I'll be sure to link back to your video too.

@DeepCreekTV

5 жыл бұрын

Yes Andrew I used polyurethane foaming glue to reassemble the chambered peices. ✌️

Very beautiful board! I want myself to do the same board! How to become your apprentice!))

John you need a profiler!

Brilliant build!!! Finally a video that helps me make a board at home. Where can i get the templates?

@DeepCreekTV

6 жыл бұрын

Braydon Thanks...I made hard templates so not available to download sorry, but I'm sure you could find something.... "Blending Curves" maybe.

5kg with fins & boxes, strength wise much stronger than foam/fiberglass, it comes down to how thick u leave the chambers so the thicker the heavier, ( 6mm on bottom 8mm on deck seems about right) i did damage the deck on this board with impact from my knee but easily repaired with araldite or similar, weight can be an issue for some but I'm finding the extra weight gives u plenty of inertia, also you can paint 2 coats of resin (no cloth) then wet/dry & polish if u like, adds about 300gms

Hi Roby M, I used Paulownia with a western red ceder stringer, cheers John.

This is so exciting. I’m in the US, and found some pauwlonia at a local saw mill. I bought a bunch of it, as it was the only tree the sawyer had ever had. The most exciting board is 10’ x 2.5’ x 2”, with the pith running right down the center. I’m wondering if I could use waterproof PVA glue, specifically Titebond III. any advice?

@DeepCreekTV

3 жыл бұрын

I have only used Titebond lll on wood wraps but I understand it does work well on chambered models, I usually use Polyurethane foaming glue.

You see a cloud, i see a rainbow, we're both looking out the same window

Very nice craftship there! Just have a few questions as I may have at this myself. 1) Do you find it necessary to have a vent system (in case of leakage) or do you think it could be done without? 2) Did you saw exact at the outline of the rocker template or leave a bit of space and trim/shape of later? Greetings from Norway

@DeepCreekTV

5 жыл бұрын

Hi Marius, no I didn't vent this board, just keep it from getting too hot. Not sure how you go with very cold conditions. If the board leaks I find a small hole in opposite rails at the widest point, put board on side and let drain then repair the small holes. 2 - yes when I cut the rockers I cut them oversize. Cheers.

Really cool video, thanks for sharing your knowledge 🙌. One question, what does the cedar stringer bring to the equation? Other than looking great 👌

@DeepCreekTV

4 жыл бұрын

Thanks... Yes, just for looks. 🙂

Hey bud! You inspired me to build my own board for kite surfing :) I'm a boat builder in the french alps! For the fins, would leaving some meat where the you put the mounts? And could you make the wood thinner? Thank you so much for you great videos! You're doing a awesome content! Cheers from France :)

@DeepCreekTV

4 жыл бұрын

Hi Yes leave some solid wood where you are planning to put fins. You can go thinner but you will sacrifice strength... but if you were planning to glass it should be OK, I'm not sure I've never gone any thinner. As it's a kite board I'd suggest you glass it with at least 6oz cloth but if you were thinking of a oil finish I'd leave it solid, no Chambers. I'm not a kite boarder but I'd assume there would be plenty of forces on the board.

Hi John, my name is Angelo. Great vid. Really appreciate all your tips. Do you think using expandable foam in the center chambers will work as long as the board is glassed?

@DeepCreekTV

5 жыл бұрын

Thanks Angelo for the feedback.....no mate don't use the expandable foam, it was an experiment that had bad results. Firstly it will add close to a kilogram of weight, secondary it will absorb water if you do happen to get a leak or damage. If you don't want to add a breather you can fill with pieces of XPS foam or even ping pong balls but they may rattle or something light & waterproof that will reduce the air space inside. ✌️

Awesome build... I may give this a whirl. Did you use a vent?

@DeepCreekTV

3 жыл бұрын

Thanks...no vent, just keep it 🆒

You rock! I love all the quirky video edits you went out of you way to include. Any lessons learned on chambering? you showed some long chambers here, have you ever had one break? I'm building a balsa blank for a 5'11'' egg shape, this vid is super helpful. how did you seal this stick, resin or ? Last question (assuming you respond) what kind of glue did you use to put the strips together? I've heard you should use epoxy and not glue, i'd love to use glue if i could. Do you have a preference?

@DeepCreekTV

10 жыл бұрын

Thanks for the wrap.... this board was badly cracked earlier this year 8-( , got hammered on a serious wave, see earlier post below, but I feel any board would have been damaged/snapped had it been in the same position. i have shortened the chambers on a new board i'm working on & Im leaving a little bit more solid timber in nose area. I seal boards with wax & oils, & I use polyurethane foaming glue. One positive thing about trashing the board was discovering the glue held up & the actual timber split, just make sure you lightly wet the timber pre gluing, instructions are on bottle, but Im not sure how well it works on balsa? but i think it will be OK as you'll need to fiberglass if using balsa as its porous. Good luck..

Hi, excellent video thank you for uploading. I’ve read through a lot of the old comments but couldn’t find the answer, how did you install the fin plugs noting that you aren’t glassing? Is just the glue underneath good enough? Have you used a board created like this in heavier surf with it surviving? Thanks again.

@DeepCreekTV

5 жыл бұрын

Thanks Rachel, I used epoxy resin putty to install the fin boxes....yes this board did get trashed in a heavy surf. I did repair it, check my video 'How to repair a wooden surfboard'. In saying that though I feel that wave would have snapped any board.☹️

u use 1 rocker template firstly, then after cambering the board & before u glue up u can take another 2 templates 1/3 the distance between the center & rail, u then end up with 3 templates. This can reduce the amount of timber & cost needed on next board. athough this can be restricting especially if u want to change the shape to improve performance. I like to draw up a outline shape on concrete first then do the maths using the rocker & outline templates as guides, (hope this all makes sense).

Hi John! I'm almost up to clambering! Thanks so much for your video! It's helped so much. Any tips on how far apart to put the supports between the chambers? I'm guessing you stagger them too?

@DeepCreekTV

5 жыл бұрын

Good Q, it's been a while since I cut one. If I remember I think about 150mm/6" at the center then shorter as you get towards the rail. Bulkheads about 15mm thick. I'm sure I've answered this Q earlier so if you scroll down though the comments you may find that post. Yes stagger them Angus. Happy chambering ✌️🙂

Good Afternoon John,Great video. I have been wanting to build a wooden surfboard for some time, but didn't want to just buy a kit. Your video has given me a new direction. Thank you.After watching this video, I questioned the polyurethane glue being strong enough to hold the seams during extreme flexing or after a violent impact, without glassing being involved. After reading through the comments, I also found the video about having to repair it later.Given your experience with the process and the results, would you recommend leaving enough meat in the chambers to use fasteners (stainless screws / dowels) to add structural strength? I know it will add weight.I really like the look of oiled wood and would prefer to avoid glassing if possible.Thank you in advance for any advice you may give.

@DeepCreekTV

7 жыл бұрын

Hi Cliff, thanks for the feedback. I have found that the polyurethane glue is very effective because of the fact that when it did come to grief the joins did not fail, the actual timber split . Remembering too that the impact that it took I feel would have broken or damaged any board. The amount of meat you leave in the chambers is a fine balance, take too much its lighter but weaker, too little its heavier but stronger.....doweling with stainless could make it stronger but then the flex may cause issues, personally I wouldn't dowel. I like to make the ends of the chambers round not square as I feel this is stronger (as in architecture). Glassing you would think would be stronger (& heavier) but for me the whole wooden surfboard thing was to get away from petros, I really like my natural oil/wax finish it works exceptionally well, but.....that's the only thing I like to squirrel away as it took me a while to develop the mix.... tung oil works well but stay away from linseed I've found it promotes mold, cheers. PS in saying all that it's all about my experience with using Paulownia, on other timbers this may not be true.

@gettinthingsdonemusic9876

6 жыл бұрын

Just a comment about what you said, "I like to make the ends of the chambers round not square as I feel this is stronger (as in architecture)." Actually by rounding the ends of the chambers it creates a smoother transition for the stresses within the wood as it is flexing while surfing. If you didn't round the cut outs in the chambers I would bet that the stress concentrations would tend to create cracks and break at those points. Beautiful board

Awesome video! But can you show more of how you put in your finboxes and the resine u use and how u do it?

@DeepCreekTV

4 жыл бұрын

Hi mate thanks for the feedback..... when I made this video 10 yrs ago I was using ProBox , I'm using Gearbox now. Here's part 2 of a 3 part series on how I put them in a wood wrap board. The technique is very much the same as I would for a chambered board. Hope this helps you 🙂 kzread.info/dash/bejne/h6mIpqOvdqzMYNI.html

@martijnvanduijn9974

4 жыл бұрын

That helps alot! Thank u!

Great video! Was just wondering what type of finish you used to seal the board at the end there. Keep up the good work

@DeepCreekTV

8 жыл бұрын

a mix of oils & wax.....but i have found tung oil works well, it just takes a long time to dry.

Wow...your method is awesome. I've been carving and working wood for a while now and this is right up my alley. Been wanting to buy a short board but they are so damn expensive, so after seeing your video I've decided to make one using your techniques. Before i get started i have a question for u ...what type of wood do you find works best? Thanks!

@DeepCreekTV

9 жыл бұрын

stephen wilson ive been using Paulownia as you don't need to glass just oil, but you could use any light tight grained timber, cedar, balsa, poplar, etc... but best to glass if using those timbers.

Board looks beautiful. Is there only one template to get the rocker for all the strips?

Thank you very much for your answer but can't we chamber the board first and Then glue the parts together ?

@DeepCreekTV

7 жыл бұрын

There's no right or wrong way in any of this but with the aid of a CNC machine this may be possible. I reckon a method to do this by hand would be a very serious mathematical / construction challenge, too much for me to work out.

What is the difference between giving a glass coat or a oil/resin coat? Why should I prefer the first one or the second one? Thank you for your awesome channel

@DeepCreekTV

5 жыл бұрын

Hi Claudio, the difference is weight and strength, if you glass with say 4oz cloth at a guess would add approximately 1kg+, if you paint on epoxy resin or vanish at a guess would add maybe 200 - 400 grams, if you oil it would add approximately 200 grams. All these finishes have pros and cons so it's what best suits you, cheers 🌞

Fantastic video! Was wondering though about how many timbers you used for this board?

@DeepCreekTV

5 жыл бұрын

Thanks, I used 16. Check at about 4.00min, the outside ones are thinner so as to remove the maximum timber in chambering process. ✌️

Bogong, bloody brilliant. Great vid, great board and great surfing. Ballpark cost to produce one??

@DeepCreekTV

7 жыл бұрын

thanks, here in Aust. about $350 for Paulownia, plus cost of machining timber, glues etc.

Hello John, Thank you for sharing your process the video is great! It lit me up, and now I'm having have a go at shaping my first chambered surfboard for static river waves. I've just got one question that I couldn't find answered in previous comments. When screwing the board together how do you prevent placing a screw where one of your chamber dividers will later be? Going with cedar and hemlock fur on this one. Thanks Again, Paige

@DeepCreekTV

4 жыл бұрын

Cheers Paige Thanks for the feedback and good Q. It's not to critical where you screw, if a screw hole ends up where you want to leave a bulkhead ( piece left between the chambers) just move the bulkhead position forward or back a little to suit. Another tip is just before you pull the board apart and take out the screws I draw up on the bottom of the board approx where I'd like to put the chambers, remembering to off set them like brick work, then when apart and in pieces transfer those marks to the sides of each piece. So if the screws holes are where you want a bulkhead, as mentioned above just move them a little. 🙂

@NomadicShapes

4 жыл бұрын

@@DeepCreekTV Thanks for the quick response ill be sure to do that thanks!

this is such a great video. thanks so much for posting. got a heap of wood and ive attacked it in a slightly different way. i used my rocker template to cut out the bits with a router. love your trick with the screws. i dont think i would have figured that out. what did you glue it together with? and what did you finish it with? does oil need maintenance after a while from being washed off?

@DeepCreekTV

7 жыл бұрын

cheers mate, I used aquadhere wood glue (pre chambering) to temporarily join the center. small dots about 3"inch / 75mm apart , polyurethane foaming glue to join post chambering. & yes you do need to maintain the oil coat a little, interestingly saltwater is slightly abrasive.

@alxvasils

6 жыл бұрын

DeepCreekTV ν

This is a great video. Thank you! I'm probably going to try something this winter. I am in Canada - do any of the contributors or people who have tried this had success with other woods that are locally available? I doubt we have easy access to Paulownia (?). Have heard balsa is way too soft.

@DeepCreekTV

6 жыл бұрын

fishkc79 what about redwood or look for a light tight grained timber

@fishkc79

6 жыл бұрын

Thanks. Will have to do some research to what is readily available here. Seems like Paulownia would be expensive to import. Will defintiely try something else for my first go at it. Thanks again for the vid, very helpful.

Please check my other video "Bogong surgery" for the latest developments on this board. kzread.info/dash/bejne/d4GHk5VpZ8Sbm8o.html

@Aint1S

8 жыл бұрын

Man, I didn't know this could be so effective... got the tools, have the time, and thought of it using a table top router. I just see all of the wasted shavings and think I could laminate one and then never start. I'm glad to see someone who's done it and perfected it. My dad would have enjoyed making one of these boards too and he was strictly carpenter. He never surfed, but I bet this could have gotten him to try. He'd passed just a few months he was of age to retire a year ago and your craftsmanship remind me of some of the impossible things he could make in a day. Thank you for sharing you board, I bet it tracks like a gun in bigger, head(+) range surf.

@DeepCreekTV

8 жыл бұрын

cheers mate, condolences.... yes it certainly surprised me when i first made one then rode it, they do have a different feel than glass/foam, not everyone's cup of tea but I'm loving the extra weight. The whole point of posting these vids is to get like minded like yourself to get in the shed & shape/carve one out. There's somethin' real satisfying about riding a nice wave on a board you made yourself.

very clever, thanks for sharing. I have looked through your posts but I cannot see any info regarding the foam you briefly show, my guess its the spray on plumbers/builders gap filling foam?

@DeepCreekTV

10 жыл бұрын

guysoceanharmonics interesting you have asked about that...it was something I tried but with minimal success, yes it was expandable foam but I only filled the center 4 chambers, the results were if I had filled it completely it would've made the board 500gms heavier, also its porous so any leaking problems would have made it harder to drain.

Very cool, 🤙from Sakhalin island. Is it possible to use another wood? Wat to try to make

@DeepCreekTV

4 жыл бұрын

Yes you can use other wood, cedar, redwood and Douglas fir work well. Just remember other timbers need to be sealed with a coating. ✌️🙂

That seems like a pretty extreme chamber. I've built 2 greg noll type longboards with chambers out of both pine for my first and ceder for my second. the ceder was for sure lighter but they're both heavy bastards. have you ever had a board break on you with those chambers or is it more the nature of the paulownia (which is inaccesable to me)?

@DeepCreekTV

6 жыл бұрын

Nah nope yeah sadly I have snapped the nose off, I find it's a fine balance between strength and weight.

Hello! amazing video! Which wood type did you use? Balsa or anyone else? Thanks Roby

Another q: Do you have or suggest putting any concave on the board? If I wanted to give color to the bottom of the board should I stain first then paint over or vis versa?

@DeepCreekTV

5 жыл бұрын

This board has a V bottom, it's up to you if you want concave. I have never used stains but it's worth experimenting, it would look cool. Let me know if you have success. 👍

this is an inspiring video. How long did this project take you? (including wait time for things to dry and glassing it)

@DeepCreekTV

9 жыл бұрын

tobias gilkes to build a chambered board depending on the tools you have is about 70hrs, obviously it gets quicker/easier the more boards you make. This project took longer as I filmed/produced each stage as I went.

Hi, thanks for the informative video and hello from Israel! A quick question, what is the benefits of the stringer, if it is being chambered? Does it maintain the properties of a whole stringer?

@DeepCreekTV

2 жыл бұрын

Gday, the stringer is purely cosmetic, it was chambered during the process....✌🏼🙂

@itamarnachum3124

2 жыл бұрын

@@DeepCreekTV Thanks for the quick response! Indeed it came out nice 😁 Can't wait to start my own built. Cheers 🤙🏽

Best no nonsense chambering technique I have seen. Thanks John! Check out my balsa Paipo board I shaped a couple months ago...

@DeepCreekTV

7 жыл бұрын

thanks.....yes very nice Paipo I love the fins, plug & inlay. nice work.

hey mate, awesome video! Just wanted to know quickly what glue you are using for that wood? thanks.

@DeepCreekTV

8 жыл бұрын

+Jessica Rugg cheers, polyurethane foaming glue

thanks John,fantastic. what type of glue do you use on the final steps putting it all back together after chambering, and

@DeepCreekTV

10 жыл бұрын

I use polyurethane foaming glue although i have used epoxy glue before, i just find the epoxy tends to stain the timber & is a bit harder to sand. I have met other board builders who don't like polyurethane foaming glue as they feel its not strong enough & its not water tight but i haven't had any of these probs as yet.

Nice board :) What is the final weight of the board? Regards

Can a longboard be chambered? Most info I have found only has short boards (fish and what not). Curious if it just gets too heavy or if chambering is only beneficial for the shorter boards. Great video!

@DeepCreekTV

7 жыл бұрын

Personally I haven't made a longboard but.....from what I understand Paul Joskie of Valla Surfboards rekindled this wood thing in Australia when he was commissioned to make a longboard from Paulownia by a group of growers from the NSW mid north coast, he first made a glassed chambered longboard.....he took it to Noosa for a surfing festival & run into Tom Wegener...maybe 1999? who then took it further. www.phoresia.org/?p=219 From memory I think Paul told me it weighed approx. 11 - 12Kg ?.... you could reduce it down a few Kgs without glassing it.

What dimension are the wood at the start

Thanks...how do you cut your outline shape without hitting screws?

@TrentSmithMusic

8 жыл бұрын

nevermind....figured it out. duh.