If you like my projects and want to support me to make them sustainable... Patreon: patreon.com/KNDYP KZread JOIN: www.youtube.com/@Kendin-Yap/join

@MelicaMari-Ni-Goon

2 ай бұрын

can u make the gerber file for 8ch remote plz

@Kendin-Yap

2 ай бұрын

www.rcpano.net/2023/12/30/how-to-make-6-channel-radio-control-range-2000m/ @@MelicaMari-Ni-Goon

@MelicaMari-Ni-Goon

2 ай бұрын

@@Kendin-Yap ooh thanks i didn't notice u have done 8 channels version

@smoochies5056

2 ай бұрын

@Kendin-Yap it is ok to use ams117 ldo on this ebyte?i just need to add 2x 100uf?

@gourabdutta9331

Ай бұрын

Your 6 channel gerber file didn't download

Thanks sir the one you have made last time was very complicated. This one however is simple yet reliable 😊

Congratulation. Very nice project and detailed description. Happy new Year !!!

Elinize emeğinize sağlık yaptığı projelerin dosyalarına kadar paylaşan nadir kişilerdensiniz. Buda sizin amacınızın sadece video çektim bitti olmadığını gösteriyor her vidonuzun altında bütün detayları bulunuyor. Teşekkürler

I really appreciate this content. Keep going. U’re fenomenal 👏🏻👏🏻

thanks for the video! I'm waiting for next generation with display and menu to ajust limits and consumptions for servo and ESC. :)

This tutorial for sure fun and educational. I'm waiting part 2 with stability and range tests :)

@qnaman

4 ай бұрын

i'M USING SIMILAR SETUP. ALTHOUGHT i'M USING STABILISERS FOR 5V AND 3.3V BECAUSE OSCIALOSCOPE SHOVED ME SOME ABERRATIONS IN SOME CASES.

You showed me allot on how I can improve my radio controller, thank you.

Gerçekten sen bir dahisin hocam ya. Türkiye seninle gurur duyuyor ❤

Neat, beautiful, all in all beautiful!

I developed a system similar to this to be used in The UAV Challenge - Outback Rescue about 16 years ago. I incorporated it into a Futaba 6 channel 72 MHz transmitter after removing the 72 MHz RF section from the transmitter case. This allowed all of the ATV's, servo mixing and servo trim levers in the transmitter case to be utilized in the new 2.4 GHz system. I have a video of it on my KZread channel. KZread won't let me put a link to it.

Thanks a lot, these will be just for my rc plane project Im about to start... Great how-to

congratulation, that is the coolest project ever seen !... thanks for sharing ...

Yine döktürmüşsünüz.

I just reading your article nrf24 conection problem.Now everithings is better.Thanks..for your time.

This is another great video! Thanks a lot for you time and knowledge. I would like you to make a video with Arduino mega and 10 channels!

Ellerinize sağlık çok bilgilendirici bir video olmuş

شكرا جزيلا اتابعك من الجزائر لقد افدتني كثيرا

çok güzel bir çalışma olmuş. ellerine sağlık

Great job, i love this

eline sağlık abi çok güzel olmuşş

Harika çalışma Allah razı olsun :)

Thank you so much ☺️

Üstad eline sağlık.

Efsane olmuş ellerinize sağlık

In the UK you should use channel numbers of 80 or less because the max frequency allowed is 2.4835 ghz

great job thanks for sharing

Wonderful creativity ❤

I will write in my language. Videolarınız sayesinde bu alana ilgim arttı. O zamanlar 9. sınıftım. 2 kere teknofest iha yarışmalarına katıldım. Çizimleriniz , uçağı yapma sürecinde işime yaradı teşekkür ederim yolunuz açık olsun.

@thavaclk5242

4 ай бұрын

( Turkiye Teknofest )

@morekmek

3 ай бұрын

bütçe vs. alabildiniz mi?

Sir subscriber from India and I am very big subscribe

Bro love you you are the best really like you You are the best

good instructions, I like your videos...

Bir eem olarak seninle gurur duyuyorum hocam .tebrikller.

@omerbilgin5323

3 ай бұрын

hocam bizde takip ediyoruz. ama pek yorum yapmıyoruz haberin olsun. sayende yıllardır bu hobiye başlamak için beklediğim ancak bi türlü cesaret edemediğim işler için ilk siparişimi verdim. teşekkürler emeklerin bizi de cesaretlendiriyor

Man you’re awesome 👏 you have to

The thing about 2.4Ghz is that back in the day when the authorities were deciding which portions of the radio spectrum they could licence out to make money from, the 2.4Ghz band was seen as worthless because it is one of the absorption frequencies of the water molecule. After deciding it was useless for radio communication the microwave oven was discovered by accident by semi cooking a bit of food someone was messing about with due to this very effect. Anyway, due to the low quality of the band the authorities decided to make it licence free and this is why we use it for wifi. If you are looking for range then the thing is not to use this band. The 870mhz band is better. Generally the higher the frequency the more the air attenuates the signal.

@mixeduptv2268

3 ай бұрын

If range matters enough, you don't built your own transmitter & reciever. It's a fun project. Plenty of range with 2.4Ghz ELRS for most people also. If range matters only then there's satellites.

@leopoldomolina1763

3 ай бұрын

Your comment is very informative 👍🏻

@davidwalker4795

2 ай бұрын

Ok

@Andrew-rc3vh

2 ай бұрын

@@mixeduptv2268 I understand ELRS uses spread spectrum. You can trade bandwidth for range either by using narrow band modulation or as spread spectrum does, it works like statistical averaging to increase signal to noise ratio and uses a wide spectrum. You can go as far as you like with this method until you run out of bandwidth. Also bear in mind the rules say you can only transmit

Excellent brother. Please make lora 20 km range 8 channel transmitter and receiver with LoRa module

thanks a lot❤❤

Great, change the antenna for 1/4 ground plane and the range will be higher. This antenna is very simple and cheap. try it!

Thank you!.

Great video. Can you make one with expo and dual rates?

Ne Harika Bi Adamsın Sen Ya

Now this is nice

ShOcK & AWE COoL. 100 points awarded! Truly SUB worthy. Thank you for the video and the detailed punch lists.. Cheers from So.CA.USA 3rd House On the Left. It's true what people are saying... You do RoCk

A really nice and beautiful project, no doubt about it. But is it worth it nowadays doing it yourself instead of buying a 6ch Tx brand new for little money.

elinize sağlık. uçuş testleri de gelir mi ? ben de yapmak istiyorum

Teşekkür ederim videolarınız uçağımı yapmamda bana çok yardımcı oldu Sana bir soru sormak istiyorum Bir fırça motorunun kaç volta ihtiyacı vardır?

Please post a tutorial on making a copy of the microzone controller❤

Excellent brother. Please make lora 20 km range 8 channel transmitter and receiver

bellissimo

great project and thanks for sharing,i have issue opening the gerber file though.and i have many nrf24l01 but i am still not able to make them work any of them.i am just clueless where the issues are.did you ever encounter such issues as well?Thanks again.

@user-dw9pg7vh7l

Ай бұрын

Здравствуйте, нужно обернуть плату NRF обычной фольгой, но перед этим каким нибудь диэлектриком, например скотчем или изолентой, и если не изменяет память, ещё нужно подпаять керамический конденсатор на 10 pF, на пины питания, и тогда у вас всё получится!

Could you make a vedio on upgrading a existing flysky radio transmitter, specifically the CT6B model. Which needs 8 batteries, that too which dries out in less thab an hour and the range is shit plus the servos vibrate(unwanted motion) when operated via the transmitter

I have a prototype of a radio controlled golf cart. I am looking for a transmitter and another radio receiver. They should be configurable so that one car does not interfere with another. I would need at least 100 meters of closet. Can you recommend any? I think they must be 433 Mhz, due to some permissions problem. Thank you very much.

Hi wonderful job Can you make remote control for agricultural spraying drone

Awesome

is it necessary to use a ceramic 100nF capacitor or using any other 100nF capacitor would be fine?

Good job!!!!

Bro your transmitter and receiver have many features

Hocam bu projeyi birde Lora e22 modülü ile yapsanız harika olur

BHAI ye plets kaha se parches kre digital jo isme ye component feet krne pade

hello, can you add calibration - transmitter with trim

Impressive 👌

Do you have a circuit lay-out for this project? Im from the Philippines by the way.

Please Do a Range Test

Love this variation like all the other versions, I have all the components, make the connections one by one and checked the cables multiple times, somehow I can't make it work. The nrf24l01p modules are not communicating with each other. If you had similar problems or have any suggestions I'm all ears. I tried it with newly bought nrf modules and arduino nano's. I am really curious about what I am missing.

@7UN4

3 ай бұрын

Also tried different and simpler codes, Tried connecting the cables directly and to 3.3v of arduino nano without that extra regulator circuit, Supplied nanos with various voltage sources, lipo's, USB ports, lab power supply, I am quite frustrated and I am not kidding its been at least 10 hours just to make it work in these last 3 days. :')

@7UN4

3 ай бұрын

Still trying, managed to make a code work but now the receiver cannot communicate with the radio, sender is constantly sending packages but no one to receive on the other hand.

Thank you @kendinYap

I wanted you to teach me how to boost these 5.8ghz and 2.4ghz signals so I can go further. I'm from Brazil

tebrik ederim süper olmuş, trim ayarı için pot koyulabilir belki. 😊

Super Awesome

elinize sağlık güzel video sorum şu: düşük tetiklenme değeri olan (30mv) bir mosfet biliyormusun yada benzer bir mosfet varsa oda olur

@Kendin-Yap

4 ай бұрын

Bilemiyorum. Araştırma gerektiren bir konu

@Omersalih053

4 ай бұрын

@@Kendin-Yapflysky i6 alıcısı için o mosfeti arıyorum sinyal ucundan arduinodan alıştığım gibi 5v vermiyormuş ölçü aleti ile ölçtüğümde fark ettim

pls make a videos on how to make the pcb

Is 1400 kv brushless motor work well with 8045 propeller? In turm of thrust and speed and avoid overheating?

I tried to program the arduino Unio and the error I got was `SPIClass::begin()' ? SPI is a part of AVR's base sofware I thought?. Both Xmit and Rec programs give the same error? Any suggestions? Rick

can you make a fastest rc plane , yes this is challenge for you 👋🏻

Can you make a code for hydraulic system and dual mode motor controller?

Hey bro. I have a question, do you think it is possible to add a ssd1306 oled display to be able to print the channel values and maybe with a voltage divider to the vin, the battery value? I was testing it and it works but not so good, as it generates a kind of latency in the signal, which makes it not work well. Of course all this with an I2C display. Great video by the way.

@Kendin-Yap

Ай бұрын

It is possible but as you have experienced there may be a delay. Arduino cannot run multiple tasks simultaneously in real time.

@BryanCruz-rk6nd

Ай бұрын

@@Kendin-Yap I think it's strange. I also used an Mpu6050 gyroscope module to rotate a servo remotely (i.e. a channel seven for that purpose) and it works pretty well, with no latency and it's also I2C, but with the oled display I can't get it to work without that latency or even sometimes it doesn't even work.

Great video！　Are 10uF and 100uF electrolytic capacitors both 16V?

@Kendin-Yap

4 ай бұрын

16V or above can be used.

@Kendin-Yap

4 ай бұрын

If a battery with a voltage higher than 4S is to be used, it should be above 30V.

@daimichi7165

4 ай бұрын

@@Kendin-Yap thank you very much!

Professor, I ask you a question: Can I change the cardboard that you use in making airplanes with regular cardboard?

@Kendin-Yap

3 ай бұрын

Regular cardboard is a heavy material. It will be very inefficient.

Could you explain why those capacitors are needed? I did something similar but without them and it worked. FYI I am electronics begginer.

@Kendin-Yap

4 ай бұрын

Capacitors provide more stable operation. And it filters out electrical noise.

Is it possible to add a ESP32 cam module in this board?

Nice! What plane is this for? I'd love to build the full object.

@Kendin-Yap

3 ай бұрын

It is for general purpose. It is not specific to a model.

Can this be used to transmit eeg signals? i want to build a robot car that can controlled by the mind

Can you use HD controllers on 50V?

Excellent sir🎉🎉🎉🎉 But sir trimming buttons is missing...🙏

@Kendin-Yap

4 ай бұрын

I have already published a more comprehensive version with trim feature. I wanted this to be as simple as possible. kzread.info/dash/bejne/hId4yK-akdGxiLA.html

Is it possible to use a 50v HD controller?

Hocam iyi günler , dron ile kumanda arasına repeater(tekrarlayıcı) yapmak için nasıl bir yol izlemeliyim

yes but can you set ESC range :)

Menzil ölçümü yaptınız mı?

Bayraktar iha prototopini yaparmısınız lütfen çok güzel uçaklar yapmışsınız birde iha olursa çok güzel olur

Hello Kendin-Yap, I like this video can you please let me know voltage of 100uf and 10uf capacitor used in transmitter? Also capacitor used in reciver?

@Kendin-Yap

5 күн бұрын

16V or above

@amolpatil9504

5 күн бұрын

@@Kendin-Yap Thanks

هل يمكنك استخدام وحدات تحكم HD على 50V؟

If only you did something that really worked.

@Kendin-Yap

2 күн бұрын

It works perfectly when everything is done correctly.

komutanım herona benzeyen rc uçak yapabilir misiniz? yaptıklarınızı ilham verici ve teşvik edici buluyorum. teşekkür ederim emekleriniz için.

It would help if you talk/explain while performing each step.

çok başarılı bir çalışma olmuş tebrikler. Ancak sizin kullandığınız gibi PCB leri nasıl temin ederiz 0:18

@Kendin-Yap

13 күн бұрын

PCB yi kendim yaptım. Onu yapabilmeniz için gerekli dosyalar linklerde mevcuttur. Diğer seçenek pcb hazırlayan ticari firmalar da var. Onla için gerekli gerber dosyaları da linklerde mevcuttur.

Im trying to make my own pc..what capacitor do i need to add on nrf?

bu nrf ile ses iletimi mümkün mü acaba? üniversal bi motosiklet kask interkom'u yapmak istiyorum da

Arabalara takviye yapılabilecek taşınabilir pavurbank yapabilir misin ustam

Lora 2.4Ghz Turkiyede robottr de var arayip bilgi alabilirsiniz

Sir please add the trim botton and make the gerber file for 8ch remote

Cooles Projekt, wo bekommt man die Platinen?

@Kendin-Yap

3 ай бұрын

I made the PCB boards myself. The necessary files are below the video.