Young Man I've been serching for days on just the video you're doing right now because of a noise I washaving in that area.And this is after spending money at a dealership that changed suspension components that were costly just to have the same noise because rubber on bushings were split. Thank you and keep sharing. God bless you.

Did you have to do anything to the steering?

Awesome video bud. Im getting ready to do my lift. Did you run into any unforseen problems?

great video . Educational .

Those look like roughcountry blocks mine r round for somereason ??

Hi I can’t see how you determined where to place the bracket before drilling 1/2 inch holes.

@dustinwilliams2556

5 ай бұрын

1 1/2 inches above the old holes

Do they make a body lift for a 22 Ram Rebel? Cant seem to find one anywhere.

@dustinwilliams2556

5 ай бұрын

the rebel is just a trim package it should be the same as a similar year model ram

Does the body lift level the truck at all? Ive read online that it does? I am trying to get this bl for my truck as wel

@wrenchwise1529

2 жыл бұрын

No, it will raise the front and rear end equally. If it’s not leveled it still won’t be

I don't understand why you took the front of the truck apart to change the body bushings. And what was that extra plate you added?

@kened6139

2 жыл бұрын

Those plates lift the bumper up to stay flush with the body. Bumper is attached to the frame not to the body.

@TeamWinnieRacing

Жыл бұрын

1. You have to, 2. The plates are bumper relocation brackets. When you lift the body off the frame the bumper stays on the frame so there would be a 1.5” gap between bumper and body

Yo , what lights did you use for your front bumper set up? I’d like to install some and have a set up exactly like yours.

@wrenchwise1529

2 жыл бұрын

Amazon nilight led pods

@E-Man-um4yd

2 жыл бұрын

@@wrenchwise1529 thanks amigo! Reason why I ask is because I got myself some blacked out D.O.T approved headlight housing units. Even with led lights my visibility is absolute crud. The set up you have seems to provide adequate lighting. Do you use yours daily at night ? If so , any pictures or experience with the results ?

@wrenchwise1529

2 жыл бұрын

@@E-Man-um4yd They are a bit too bright for constant use but great when you need them

Only thing the instructions didn’t tell me is where to drill. Just says place bracket in front of frame horn and mark where to drill but doesn’t say where to mark

Great video man, do you have to put a steering adapter in?

@wrenchwise1529

3 жыл бұрын

No you do not

@eduardobronson8653

3 жыл бұрын

Instablaster...

Nice video but I wish you would have included the back

@wrenchwise1529

3 жыл бұрын

Intended to, but lost some footage. Sorry about that. It is a very similar process though

@Italianborn

3 жыл бұрын

@@wrenchwise1529 so even for the rear you would have to take off the whole bumper ?

@wrenchwise1529

3 жыл бұрын

@@Italianborn Yes and relocate it otherwise there will be a one and a half inch gap

Almost seems easier to get a full suspension lift lol

@biggamehunter9138

2 жыл бұрын

This along with bilatein shocks and a spacer lift in the rear is a way cheaper way to get a 4” lift

@TeamWinnieRacing

Жыл бұрын

I did a 3” level $100, adjustable ball joints $100, 1.5” body lift $150 much much cheaper than the 4” sus lift. Flies down trails just fine.

Will this affect the fan shroud

@wrenchwise1529

Жыл бұрын

Yes