thank you! it is very explanatory information. i am planning to get ecu kit for my zx14r.

@SirREM

3 жыл бұрын

You are welcome!

Woolich is simple to use and they have great support service!!!

@johnnyappleseedz422

9 ай бұрын

...when they actually respond.

Nice, thanks!

@SirREM

5 жыл бұрын

Glad you liked it.

Very nice! thank you a lot. going to purchase the Usb or Log box but not sure which one to go ? Can you please give some advice for new beginer me ? my bike 2016 ZX10r and be flashed by Mail-in place far to where i live. It not always comfort to send it go and back that far as the bike need adjustments by times.. but hear that the Tuner will have the Keys and no one can log in the Ecu to do whaterver his maps except him. I will ask him soon about this. Just wanna DIY things and learning. Or i need to send him the Ecu to back it Stock?( since the bike so far is good and really enjoy the Flash. Thanks !

@SirREM

2 жыл бұрын

I am sure a lot of things have changed since I installed that 5 years ago. So not really sure which would be better in todays world. I maybe getting a new bike next year then I will look into it more. I would just do some google research.

Hey Rem... Why did you decide to go with Woolich? What happened to the flash you already had for the bike?... I am probably going to Woolich as well as the flash I got just isn't to my liking with a few glitches in it.. After doing as much research that I can, I think Woolich is probably the best thing on the market to make a flash "user friendly"... Thanks for the vids you post.. J

@SirREM

5 жыл бұрын

When I dynoed the bike after the ghul flash it tripped an error code and all the dash does is blink. Woolich lets you reset error codes. Plus I can mess around with the tune now.

@marvin2288

5 жыл бұрын

@@SirREM Right on. I had an error code right away from the o2 sensor. Luckily I knew a guy that had the service manual and told me what it was and how to clear it. I like that Woolich has map share that can be downloaded and used from others. Will eventually learn to adjust the ECU but might be easier to find a good map someone has and test it out. If I'm happy w it, I would just run it. Lol. Look forward to your future vids when you start adjusting.

NO SNOW HERE! NOT MUCH WATER EITHER...SOCAL

So how much power over stock did you achieve with this kit? What are your mods and wheel HP?

@SirREM

3 жыл бұрын

I have not did a dyno run with this kit as of yet.

@sheridancowling6257

2 жыл бұрын

Tuned yet?

hi i have a woolich racing and i would like to know how can i install Quickchifter on my suzuki gsxr750 2012 thanks 😊

@SirREM

4 жыл бұрын

I do not know much about that bike. I would check woolich racing forums. They should have something there.

@jankarlosgonzalez8325

4 жыл бұрын

@@SirREM thanks

I just bought a 2022 zx10r has 250 miles on it, MooreMafia has a handheld device such as this one they go through Woolich they can email me a tune like BT moto has, is this pretty much the same install?

@SirREM

Жыл бұрын

I had a tune from another place but I do have the woolich software so I can retune as needed.

@Lyrethar

Жыл бұрын

@@SirREM k ty

Hello, can I just get the harness and bin file and use my friend's usb v3(same bike)? Will it work or do I need to get the whole kit?

@SirREM

4 жыл бұрын

one for each bike. It is coded to the ECU once used.

@suryareddy6346

4 жыл бұрын

@@SirREM thank you!!

@suryareddy6346

4 жыл бұрын

@@SirREM can you please confirm if the KDS plug is the one with red wires or green spring kind of things? In your video it shows to connect to red wires plug but the Woolich user guide shows to connect to other plug.

@SirREM

4 жыл бұрын

@@suryareddy6346 It has been so long ago when I did that project. I am pretty sure I followed the guide as it was at the time. Maybe they changed something. I would follow your instructions.

@ZX10RArcher

3 жыл бұрын

@@SirREM Here because someone couldn't write their ECU following this video and told us they followed this video tutorial to install their harness. The instructions have been the same since the products were released back in 2016, I know since I wrote them. The connector you're connecting to at 4 Minutes 30 seconds is the KDS connector for the ABS system. THIS IS INCORRECT. The connector in our instructions explicitly show a clear connector with the proper wire colors. If connected to the black ABS connector, you will not be cable to read/write or see live engine data. The 13a bike harness needs to be connected to the OPAQUE KDS connector with the following wire colors *as shown in our install guide*: light green, light green /w black, brown /w white, light blue, grey /w blue and black /w yellow.

Hey guys does the log box unit stay on the bike

@SirREM

2 жыл бұрын

All the wiring installed is just to connect it to a laptop to read the ECU. So there is no log box other then the ecu logging the information that you extract with a laptop.

@yusrihisaacs898

2 жыл бұрын

@@SirREM thanks a million my friend... Really appreciate it... As I was explained a bin file is loaded to my ecu for the Woolich software and it's unique to my bike only

Hello Friend. It's OK? Do you have to sell this equipment? I live in Brazil and do not exist around here. I'm waiting Thank you for now Att Vand

@SirREM

5 жыл бұрын

Not sure if they sell to Brazil but you contact them and see. www.woolichracing.com/

Dang my package didn’t come with fancy instructions... SOL

@SirREM

4 жыл бұрын

You might have to get them from the web site. It has been so long that I forget if they came with instructions.

Haven’t seen any bike videos for ages, is there something wrong, or just not doing it anymore

@SirREM

5 жыл бұрын

Life took a twist on me. I will be doing bike videos again at some point. I just took my first ride of the season over the weekend. I have two videos that I made earlier this year but have not edited them. Maybe in the next week or so I will get one of them done.

@MrPninja

5 жыл бұрын

Oh I hope your ok mate ?

@SirREM

5 жыл бұрын

@@MrPninja Yes I am okay. I will explain things on my channel in the future.

Make sure when you start to flash your bike that you have a strong internet connection! Also make sure the computer that you are using has USB 2.0. Anything above 2.0 and you will have problems!

@SirREM

5 жыл бұрын

Yep that is in the instructions provided. Thanks

@twistedsocal

5 жыл бұрын

anything below 2.0, You can use usb 3 with zero issue as it is fully backwards compatible. The internet connection is a huge deal though, if you lose connection mid flash you will end up needing to either buy another bin or wait on support to reallocate your current one

@alexanderzayas8213

4 жыл бұрын

Josh Hall that is great info to know hahah. Wow that sucks.