The video has nothing to do with installing or tuning the carburetor.

@nibbiracingusa

Жыл бұрын

More videoes about tuning are coming soon, stay tuned!

@The77stevo77

Жыл бұрын

​@@nibbiracingusa change the title of the video jack hole 😡

@dustysteele5408

Жыл бұрын

😂 Carburetor assembly*

@Ac22768

Жыл бұрын

@@nibbiracingusa so rename this video since it’s not accurate.

@mrbeans2425

9 ай бұрын

Carb assembly not install lol

Is the spring gasket absolutely necessary? I lost mine 🤦

The chock on my 24mm nibbi carburator doesn't stay in open position. After starting the engin chock close up by itself by vibration of engin. Any advice how to fix it?

I'm trying to tune my sons xpro storm 125cc with the 22mm carb and having trouble. Where is the factory idle screw set from the factory?

Does it have Power Jet? I am not sure, please someone who explain because my bike get dry when I accelerate until the end of the grip

where do you install the tube for the vacuum in the fuel cock?

🔥🔥💯🏁

PE 30mm work on mid-modded Blaster?

What did he mean by the oil volume is equivalent to a 1/4 of the throttle?

pls upload a video of adjusting the float level

@nibbiracingusa

9 ай бұрын

Will do!! Keep following and stay tuned! :)

I'm pretty much sure you got idle screw and pilot screw information wrong. Amazon says red nob is air fuel ratio and idle screw is the screw you said is pilot screw. Amazon diagram shows this. And I'm pretty sure I can verify that because I adjusted it with low fuel, idle went up . Then when I filled tank up fuel flooded out my bike, then I had fuel dumping out carb. So when I turned red nob to right I was adding more fuel, idle went up, Just be aware. Read manual to find out. Someone please verify if I'm correct.

I have a 125cc 4T, with an aftermarket camshaft and an exhaust. Rest of the engine is stock. I want to upgrade from 18mm to a bigger size. Which size would be better? Also, do you have a seller in Greece??

@nibbiracingusa

9 ай бұрын

Hi there, email us the specifics of your application for the best fitment at help@nibbiracing.com! :)

i have a pwk 24 that idles high on choke and dies off choke, but then once running with throttle blipping to keep it going the idle is all over the show

@lukie4ever

5 күн бұрын

I think it hase something to do with the pilot jet, too small or something

Which model works for a 2003 suzuki quadsport 250 and what other adapters doni need if any?

@nibbiracingusa

7 ай бұрын

Hi, please contact help@nibbiracing.com( email).

Where can u buy the rubber flange that goes to the engine?

@nibbiracingusa

Жыл бұрын

Hi Fabian, thanks for your interest! Please visit our site to shop for the correct intake manifold. Any questions about fitment, installation, and compatibility, feel free to email us at help@nibbiracing.com. >nibbiracing.com/

Pe22 karbüratör için kutusunun icinden cikan hangi jetleri kullanmam lazım performans için?

@nibbiracingusa

7 ай бұрын

Merhaba, lütfen help@nibbiracing.com (e-posta) ile iletişime geçin.

Hey, can i use the PE 26 mm on a stock banshee?

@nibbiracingusa

7 ай бұрын

Hi, please contact help@nibbiracing.com( email).

HOW TO PUT NIBBI CARB TOGETHER.

Hey I've got a 206cc engine I want to upgrade the carb. What nibbi carb be compatible?

@nibbiracingusa

10 ай бұрын

Hi, 28mm could be compatible. Kindly head to our site for more details, thanks! :)

@unyieldingrage1389

9 ай бұрын

@@nibbiracingusa”Could”? Very helpful 😂

@qublo9183

Ай бұрын

​@unyieldingrage1389 he wasn't specific just said 206cc, I guess he's supposed to read minds.. silly me😮

Nibbi your carbs are beautiful but I've been getting nothing but failure with the needle seat. This is my second one and I decided to adjust the tang but I noticed the needle has the dreaded ring and is allowing a tab bit more fuel in and it's leaking small drops from the over flow.. Guys please fix this, I'm all for tuning and adjusting to what my engine needs but I shouldn't have to buy new parts to make something work that was purchased new

Your video is very informative n you seem to be very knowledgeable. Can you tell me what jets and needle setting should I use on my nibbi pe28fl for my 250(239)cc Chinese bike? My elevation is 774

@nibbiracingusa

10 ай бұрын

774 meters? or 774ft?

mine is having issues

@nibbiracingusa

9 ай бұрын

Hi, we're sorry for this. Please email us more details of the issues you meet so we can help better, sorry again for this inconvenience. Email: help@nibbiracing.com

@admin I would like to start as a dealer in Bangladesh. Please notice me,

@nibbiracingusa

11 ай бұрын

Hi, thanks for your interest in Nibbi Racing's products. To become one of our dealers and start to distribute Nibbi's items in your area, kindly check the link below to apply for the dealers' application. Thanks again! :) nibbiracing.com/pages/dealers-application

I have nothing but trouble with my nibbi carb I tried everything from float adjustment to jets swaps junk nibbi please don’t buy junk

Bro that’s not an installation

The translation is a little dodgy.

What's up about the unseeded gay black gloves?

I bought the pe22fl and it leaks when the engine is running through the overflow any ideas?

@hamzahmushtaq877

7 ай бұрын

Your float needle is sticking, give the bowl a couple of taps with the plasric side of the screwdriver

@letsgetit3310

4 ай бұрын

Check out my comment. I just had this issue. I'm pretty sure what he said is idle screw is air fuel mixture. So when i" turned up idle" i was dumping fuel in. Yeah idle went up. But once I filled gas tank it caused a fish thank siphon effect and dumped out my bike. Then it was dumping out carb. I turned it back down and it stopped over flowing fuel. My guess is you should always adjust carb with full tank to identify any issues. And half a tank I didn't have any issues that I know of.

I did not pay attention. Thanks nibbi for making a boot. Is gonna be okay