If you need some great all season floor mats for you car check out 3D Mats using my link below. 3D Mats: bit.ly/3K1qCuo $10 Off: ADVENTURE3D10

I appreciate the hands-on videos. It gives a good perspective.

@TheAdventureAuto

7 жыл бұрын

Thanks! I like hearing that kind of feedback.

Thanks for the install vid and sound clips! Just did the install myself on my ‘15 2.0. Loving the sound and completed look with my other mods. Thank you most for suggesting the hangar pliers, what freaking life saver. Your vids really help in deciding to go Borla. Thanks!

Hi I wonder if this thing is will fit on 2018 mazda 3 sport? Its also a 2.0 on mine .

Oooh, I was looking at Magnaflow and Corksport too, but the Borla sounds really good. I have a 15 2.0L manual hatch, I want something with a deep exhaust note that doesn't sound ricey.

@dizzyallday3230

4 жыл бұрын

I have the exact same car, did you end up going forward with your purchase? how is it?

If you put 2 nuts on, the bottom but acts as a head since the top won't won't turn. So you wrench the bottom one removing the bolt. It's also a good way to remove bolts with bad heads. Also, if you use a smaller top but than the bigger one, you can use a ratch since the small one won't be grabbed.

I ordered the Injen intake and Borla Exhaust last week for my 2012 Mazda 3s GT. since it's pretty much the only performance mods I can do to her bc it's not the MS3. I can't wait to get it and install them. I was going Corksport but I think Borla sounds better. good job buddy

@TheAdventureAuto

7 жыл бұрын

I agree that Borla sounded better after listening to both multiple times. Good luck with your mods!

Man, your videos are great! Really helps me with my 3 :)

Good video , but this is for Borla what the Fucck Borla you want us to spend big money for your exhaust and you give us zero bolts the fit exhaust, so you have to go to HD to buy bolts. That sucks

@TheAdventureAuto

7 жыл бұрын

Yea I'm with you. If the instructions said how to remove the factory bolts and re-use, thats one thing, but it gave no direction and it was all securely attached and nuts welded on. And the "reusable" gasket isn't working out either. Theres a gap and I am going to add a separate gasket in to try and fix.

Wow, I just always assumed there was some form of welding involved with installing exhaust systems. Everytime, I ever seen one installed (not this one) - the guy was welding and cutting metal.

@TheAdventureAuto

5 жыл бұрын

Some exhausts are more difficult than others. This was fairly simple with the exception of no included bolts or connecting gasket.

Filmed horizontally:)

Yeah I guess borla includes hardware now. Just installed this baby today on my 15' Mazda gs and it sounds so fucking good. Nice video subbed.

@TheAdventureAuto

6 жыл бұрын

+Madison Watson Hey man glad to hear you love the sound. I wonder if Borla just forgot to put the extra hardware in with mine. Otherwise it was a huge oversight on their part. Thanks for stopping by!

@terrorreloaded5643

3 жыл бұрын

Where did you buy your exhasut

The "tin can" comment isn't meant to be derogatory, but it relates to the super lightweight body, which has very little sound dampening. I spent a good bit of money to add sound insulation to the doors to quiet the road noise, which did help.

@TheAdventureAuto

7 жыл бұрын

Bill Thomson Gotcha. Thats good to know you had good results when insulating doors. Thats the only place I have yet to add some but was considering.

Oh so I wonder if I could do this without a jack and jack stands... I don’t have them but I guess I could try since my car isn’t lowered....

Any exhaust for 2014-2018 Mazda3 that says reuse the factory bolts is wrong. Same for other similar era Mazda vehicles.

does one of the mufflers only go half way in the y pipe and the other one goes in half way int the y pipe? is that how it is suppose to me?

Any drone?

So it’s been about a year and a half. How is it treating you? Have you been pulled over?

@TheAdventureAuto

6 жыл бұрын

Still really enjoying the sound of it. It sounds great when going WOT. Haven't been pulled over in more than 6 years now :)

did the 1.25 end up working im assuming?

Sounds really cool IMO

I totally love the car.

All you gotta do is dremal the small tack welds off the stock exhaust nuts sure its an inconvenience but wouldnt take much time

Anyone know if the borla would fit in the sedan?? Even with welding the tips down?

So this is the exact system I would like to install. How much on wields and system?

surprisingly easy install. Good job. btw you can try some WD40 on the OEM Muffler and get the old nut and bolt off.

@TheAdventureAuto

7 жыл бұрын

ZeroColdx911 Yea i was going to try and get them loose but realized that the nut was fastened down. It would have just gotten me a bolt with no end. I would have had to have nuts on both ends rather than just buying a new bolt. BIG decisions :D.

Will this exhaust fit on a CX-5 ?

What's the link for the tool? Thanks.

@The Adventure Mazda I see the hatch tail light blinking. Is that a led flashing bulb or did you get an adapter. I love the blinking rate. All others I've came across are too fast. Can I have a resource to buy them please?

@TheAdventureAuto

6 жыл бұрын

The blinking light came from the factory that way. Unfortunately i dont know how to add it for those that it didnt originally come with it.

Did you notice any increase in horsepower or performance from adding the axle back exhaust and the after market intake? I have a 2015 M3 2.0L that I am interested in doing the same mods to. Love your videos! Thanks in advance!

@TheAdventureAuto

7 жыл бұрын

It's really hard to tell to be honest, but I've said it before that I can definitely feel more high end power. I'm currently in the process of testing my intake to see the temperature difference and heat soak results when compared to stock.

I love a good sounding exhaust but these cars are tin cans and I worry about the sound resonating too much into the interior of my 2014 3i Sport sedan. What do you think?

@TheAdventureAuto

7 жыл бұрын

William Thomson Haha if you think your car is like a tin can why did you pick it? The borla has some drone but not bad. I added sound deadening and now its gone. Go for it!

How did you do it by yourself!!! haha. Stupid screws that are stuck on the stock exhaust.

@TheAdventureAuto

7 жыл бұрын

Greg F. Pettus I watched your vid a while back but cant remember if you had screw issue. And yea it wasnt bad to do alone :)

does this effect the warranty at all?

@TheAdventureAuto

7 жыл бұрын

Any kind of modification can. I only modify parts of the car that I can easily swap back to stock due to a lot of dealers being stingy with what they cover.

Make sure to disconnect battery so computer can reset wit new exhaust...

@TheAdventureAuto

6 жыл бұрын

I didn't even think to do it with an exhaust. It just learned it over time while driving.

Do you need the lower bumper with holes for the tips, i have the 2.0 sport with no holes

@TheAdventureAuto

2 жыл бұрын

The hatch has the holes. The sadan is the one without. It's not compatible w the sedan.

@johngentile8561

2 жыл бұрын

@@TheAdventureAuto do they make a kit for the sedan

@TheAdventureAuto

2 жыл бұрын

@@johngentile8561 Yea it's a separate kit where the pipes angle down like from the factory.

@johngentile8561

2 жыл бұрын

@@TheAdventureAuto thank you

Don't forget to subscribe, like, comment, and share! Thanks!!

Nice! Does it have droning sound when cruising?

@TheAdventureAuto

7 жыл бұрын

There is definitely drone with this exhaust. Its not terrible but when cruising on the highway its there. Im adding more insulation to help with that.

So which way does the Y pipe go, upside down or right side up, it's driving me insane lol

@TheAdventureAuto

6 жыл бұрын

Yea it drove me insane too and I concluded that it didnt matter which way it went. I went back and forth and never seemed to figure it out. It would be nice for them to say in the instructions whether it mattered which way it went.

Is that the mazda touchscreen head unit or aftermarket?

@TheAdventureAuto

4 жыл бұрын

It's the factory unit.

Where's the donut that is supposed to go in between the center pipe and the muffler that is why you have that Gap it's not because of the screws

@TheAdventureAuto

6 жыл бұрын

It didnt come with a donut. Are you referring to a gasket?

i have by new mazda with 165 hp i have 2,800 km i have sport exhaust but not sport sound some people say i must wait till 5000 km is that right ?please answer

@TheAdventureAuto

4 жыл бұрын

Disconnect your negative battery terminal for 30 minutes to speed up that process. Mine sounded the same from when I first put it on to after having lots of miles.

@lukai30n59

4 жыл бұрын

can i now Disconecting battery for 30 minutes now i have 3000 km thank Man for answer

@lukai30n59

4 жыл бұрын

Disconecting battery for 30 minutes when is car off and wait 30 minutes and back rigt or?

Same exhaust problem with the miata. The entire bolt is supposed to come out, but the nut likes to separate from it.

@TheAdventureAuto

7 жыл бұрын

Tyler Watthanaphand I dont remember having this issue when i upgraded my miata exhaust. What exhaust are you running now? The race is off?

@tylerwatt12

7 жыл бұрын

Yes I put the Flyin Miata Hush-o-Matic on, after some issues with the valve rattling, It sounds great. I typically put it in quiet mode, it has a a raspy tone at 3250-5000rpm love it

@TheAdventureAuto

7 жыл бұрын

Tyler Watthanaphand I agree I love the rasp this engine has at the top end.

Had the same problem with the y-pipe. It kinda leaves a gap. Something i realized is that the face of the y-pipe that meets whith the mid-pipe is slightly curved and fuel leaks out of it. Still haven't been able to fix it :/

@TheAdventureAuto

7 жыл бұрын

Did you see where I added some sealant around the gap in my pipes? It sealed it right up and has held up really well.

@Brandon-vx6xd

7 жыл бұрын

The Adventure Mazda ahh i see. What did u use exactly??

@Italianborn

6 жыл бұрын

that it isn't fuel my friend...the drop you have noticed are condensed water

@SodaSenpai1337

5 жыл бұрын

@@TheAdventureAuto I just bought this exhaust for my 2018 hatch, what kind of sealant did you use to seal the gap in between the mid pipe and the y pipe?

@tehRokahh

4 жыл бұрын

@@TheAdventureAuto any update? Got the same gap issue don't see any sealant mentioned in the video

I got the Borla Exhaust and the nuts and bolts were included, that's wired 🤔

@TheAdventureAuto

7 жыл бұрын

Well thats good that they got things together. Maybe they saw my vid! :D

What is the spoiler you have ?

@TheAdventureAuto

2 жыл бұрын

It was a dealer option as part of a body kit. I opted to just buy the roof spoiler painted to match the rest of the car.

@goofytuber9011

2 жыл бұрын

@@TheAdventureAuto ok so that means that mazda dealers sell bodykit for this car? i didn't know that

Any gain on the performance?

@TheAdventureAuto

5 жыл бұрын

Nothing noticeable, but im sure there are minor gains from being more free flowing.

Where can i buy it online and how much does it cost?

@TheAdventureAuto

5 жыл бұрын

Currently it looks like autohance has them for $599. Search online every so often to see if prices change or you find a new seller.

Is this exhaust available for a 2014 Mazda 6?

@TheAdventureAuto

6 жыл бұрын

Honestly I'm not sure, sorry. There isnt as big of a market for moddifying a Mazda6 so I'd be surprised if they had one available. There has to be something out there for you tho.

Hey man, I enjoy watching your videos. I have a white mazda 3, 17s. And I wanted to know if there's a muffler like this for the sedan models. Ive been looking but it's been hard to find. Pls help me out

@TheAdventureAuto

7 жыл бұрын

Borla doesn't offer one for the sedan but Corksport does. Here are two options for you. Cat-Back: corksport.com/2014-mazda-3-cat-back-exhaust-sedan-hatchback.html Axle:Back: corksport.com/2014-mazda3-axle-back-exhaust-sedan.html

@fknpapa

7 жыл бұрын

Thanks man. I looked everywhere. but I've been having a hard time finding the right fit. I'm still under warranty, so i plan to just buy the Axle back. Thanks again, really appreciate your help

👍👍👍👍👍

does this remove your resonator or cat?

@TheAdventureAuto

7 жыл бұрын

No. Its basically just a new rear muffler as it connects to the point right near the rear wheels.

@immortal4942

7 жыл бұрын

TheAdventureMazda oh so just an axleback? ok thanks i'm trying to find just the exact mufflers to retrofit on my 2017 sedan since borla doesn't offer the exhaust system.

stack gaskets lol

@TheAdventureAuto

6 жыл бұрын

+alex R. Haha cant say Ive never tried that.

Only a novice works under a car with no axle stands !!!

@TheAdventureAuto

7 жыл бұрын

Alan Cooper I had a jack and jack stands. Must not have shown up in the videos.

Dogback>Catback>axelback>brokeback...

@TheAdventureAuto

6 жыл бұрын

Went over my head.