How To Install The AMS Flex Fuel Kit On A Q50 RedSport
Автокөліктер мен көлік құралдары
In this video, I demonstrate how to install the AMS Flex Fuel kit along with the AMS Big Bore HPFP and Deatschwerks inline fuel filter on my Q50 RedSport 400. You can use these instructions to install the kit on a q60 as well. Make sure to follow my build by joining the squad.
[Affiliate Links]
Torque Wrench: amzn.to/3tPjN7Z
Mechanic Tool Set: amzn.to/3DNIfuP
AN Wrench: amzn.to/3ERNxXq
Deatschwerks Inline Filter: amzn.to/3DKljwn
Music: Colossal Mind
Пікірлер: 61
On the quest to beat stock turbo records. Consider subscribing y'all!
@Sance31
3 жыл бұрын
ZillaFullBoost where you located ?
@ZillaFullBoost
3 жыл бұрын
Florida
Thanks bro. Here we go!
Is theirs an app where u could track what e u running like the fuel it one?
What size nylon braided hose is it for the line you need to replace that goes to the gas tank?
@ZillaFullBoost
Жыл бұрын
I think it’s a 3/8’s line if it’s smaller it would be a 5/16. I’d probably upgrade to a 1/2 which is a -8AN if I was to do it.
Which one of your vids do you install YNt AMS Hpfp?
@ZillaFullBoost
2 жыл бұрын
I didn't do an in-depth video on that because there were other videos already. I installed it at the same time I installed my flex fuel kit.
Good guide. How long would you say this took you? Plan to do my own soon.
@ZillaFullBoost
3 жыл бұрын
It was about 1hr to 1hr:30min
when tapping into that amp, does the car have to be fully on or can it be in accessory mode?
@ZillaFullBoost
3 жыл бұрын
I spoke to you on FB right?
@nohandoutsgarage
3 жыл бұрын
@@ZillaFullBoost yup, appreciate you. keep the good vids coming 🔥 I’m about to get active on my channel handing out the gap sauce🏎💨
How did you push the white pin out with your pick tool?
@ZillaFullBoost
Жыл бұрын
Pushed on the back side of the pin.
So you don’t need the fuel line that goes down to the fuel tank?
@ZillaFullBoost
Жыл бұрын
Nope
How long does it take for the car to stall after fuse is out
@ZillaFullBoost
3 жыл бұрын
A couple mins I believe. You can just put a tag over the line and pull it. There really isn’t that much pressure just open the gas cap.
Do I need injectors to run the E85?
@ZillaFullBoost
3 жыл бұрын
No you can run E on stock injectors. Just get a HPFP and LPFP.
Does the white wire has to go all the way down?
@ZillaFullBoost
2 жыл бұрын
yup
Hey what year is your red sport? I believe the 2021+ pin outs could be different
@ZillaFullBoost
3 ай бұрын
2016, Yea the canbus architecture is different in 21+
@Boostin88
3 ай бұрын
@@ZillaFullBoost Do you know of any kits available for the 2021+ system?
@ZillaFullBoost
3 ай бұрын
@@Boostin88 have you tried contacting AMS?
do you need the fuel filter to go along with it? if so, does it have to be the ams one cause that thing cost some serious money
@ZillaFullBoost
Жыл бұрын
You don’t need it, but it’s a good investment. I bought the DW one and installed it between the flex fuel sensor and the HPFP.
@Takk101
Жыл бұрын
@@ZillaFullBoost can you link me to that bruv. and any other similiar. 300 for the ams is a lot considering its 500 for the flex fuel sensor. also since we have this inline with the car computer, we dont have do the e calculator we just full up?
Can i connect the v2 to fuel it app?
@ZillaFullBoost
2 жыл бұрын
I don’t think the V2 comes with the fuel it Bluetooth connector, so no. You can buy it separately from fuel-it
@AwdVenture
2 жыл бұрын
@@ZillaFullBoost but we can see through our ecu dashboard am i correct? Thank you for your vids by the way bro. You just gained a subscriber 🤟🏽
Hey how did you figure pin 60 I didn't see any numbers
@ZillaFullBoost
3 жыл бұрын
It’s the 7th pin from the right. Left of the yellow wire and right of the red one. Between those two wires (red and yellow) you will have two blank openings with white plugs. It’s the one closest to the yellow wire.
@richardsolano484
5 ай бұрын
@@ZillaFullBoostwhat if there is no plug and it’s just wires
@ZillaFullBoost
5 ай бұрын
@@richardsolano484 insert the new wire. If there is already a wire in there maybe it already had flex fuel installed.
Im tuning my csr next week and vecdone my own installs but thid one has me lost
@ZillaFullBoost
2 жыл бұрын
It’s not that hard. If youve done your own installs you can do it.
@Hitch_49
2 жыл бұрын
@@ZillaFullBoost thanks man this one intimidates me i dnt wanna mess with the pins
So u got the v1 instead of the v2?
@ZillaFullBoost
2 жыл бұрын
yup. It was an old one I bought from someone that never used it.
@Hitch_49
2 жыл бұрын
@@ZillaFullBoost where arecu located
@ZillaFullBoost
2 жыл бұрын
Treasure coast of Florida
@Hitch_49
2 жыл бұрын
@@ZillaFullBoost if you were in cali I would’ve gone to u
@ZillaFullBoost
2 жыл бұрын
Don’t be so intimidated by it. Give it a shot.
Yeahhhh I’ll just pay somebody to do it….
@ZillaFullBoost
2 жыл бұрын
If you think you can’t do it it’s better to pay someone, but sometimes these look more intimidating than they really are.
@udymmas
2 ай бұрын
Lmao I be thinking the same thing when I see some videos 😂 time is money, knowledge is wealth tho
This seems so complicated man
@ZillaFullBoost
2 жыл бұрын
It isn’t too complicated, but if you don’t feel confident don’t do it. Pay someone to install.
Bro that dumb ass white wire doesn’t go in 🤦🏽♂️
@ZillaFullBoost
3 жыл бұрын
It takes some finessing
@TheHerobryan1016
2 жыл бұрын
How you out it in the wire just keeps bending
@datvr3097
2 жыл бұрын
Bryan Guzman y’all ever figure it out ? I’m having the same problem. Damn wire doesn’t want to go all the way in
@TheHerobryan1016
2 жыл бұрын
@@datvr3097 i bought a pick tool from autozone that was thinner than the port of the ecm. And I just stuck the white cable in with that like I poked the white line pushing it thru with some slight force.
@datvr3097
2 жыл бұрын
Bryan Guzman is it holding up?