How to install Shelby hood pins using the required Shelby install kit
Автокөліктер мен көлік құралдары
Installing hood pins can be scary because there are no take-backs when drilling through major body parts. I will show you how without any pain, using the Shelby install kit can be tricky.
• How to install Shelby ...
Quick Links for this video
00:00 Beginning
00:13 First remove the hood bumpers
00:52 Shelby hood pin install kit explained
02:22 Prepping the hole and installing the hood pin inserts
04:20 Drilling the holes through the hood
08:35 Attaching the latch cables
09:28 Attaching the plates on the hood
11:18 Taking a good look
Other Related Content
Install steps for your Line Lock on S197 Mustangs, GTs, or GT500s: • You need this for your...
How to Install an MGW Shifter on a Shelby with a TR6060 6-speed tips & tricks: • How to Install an MGW ...
How to Quickly Replace 2 Piece Rotors: • How to Quickly Replace...
How to fix the clicking S197 dashboard (a.k.a. Replacing the A/C floor door actuator: • How to fix the clickin...
How to safely do burnouts with your manual transmission Mustang with or without line-lock: • How to safely do burno...
What I love doing with my GT500: • What I love doing with...
Turn a Quiet Father's Day into a Special Burnout Father's Day: • Turn a Quiet Father's ...
Cordello Customs (for powder coating)
Brad Cordello 6233417606 (Tell him you saw Doc's video)
2127 W Melinda Ln, Phoenix, AZ 85027
Shopping Links
Coilover Link:
www.maxpeedingrods.com/produc...
10% Discount code: docsboost
EXO Drones shopping link:
exodrones.com/?rfsn=6571839.9...
Shop Amazon now for some great Shelby gear:
amzn.to/2JSbXXU
Пікірлер: 28
Thanks so much for the great video!!
@DocsBoost
Жыл бұрын
Thanks for watching. I am glad it helped. I appreciate you taking the time to comment.
You always have THE BEST GT500 Tech on KZread!!
@DocsBoost
Жыл бұрын
Thanks, sir.
Nice pins
Nice I wish my install kit was the same thread as the hood pin because it’s not.
@DocsBoost
3 ай бұрын
What??? That does seem to make sense. Maybe Shelby sent you the wrong kit.
@stephenbaker2056
3 ай бұрын
@@DocsBoost the installation kit is discontinued now called today I’m getting a refund for install kit.
@DocsBoost
3 ай бұрын
I better hide the one I have. LOL
@DocsBoost
3 ай бұрын
Glad to hear you are getting a refund.
@stephenbaker2056
3 ай бұрын
I already installed mine and came up with a possible solution. Is there any way you can measure how far your pin sticks up past the beauty ring?
Very good. The metal is super thin in that area, you must becareful
@DocsBoost
Жыл бұрын
For sure. Be careful. If you go too big, the insert cannot grab and hold. If that happens, you need to take a large washer and with a step bit, open the hole to 3/4" and make sure the hole is a tight fit on the insert. Then carefully spot weld that washer over the bumper hole that is too big. That works because I had to do it on the passenger side. It works great. So just be careful taking those holes out to 3/4".
How to screw on the bolts onto shelby rings ???
@DocsBoost
4 ай бұрын
The whole operation of getting the "compression" or "rivet" like inserts installed is trickier than you may think. If you get the hole just a little too big, the insert fails.
@RonVik7
4 ай бұрын
@DocsBoost that's what I did ;( the hole os too big. Now I am gonna have to use screws to install them. Do you spray drilled holes with anything to prevent rusting ?
@RonVik7
4 ай бұрын
@@DocsBoost also does the hole have to be perfectly round?
@DocsBoost
4 ай бұрын
For best results get it round as possible and make it a tight fit. You will be glad you spent the time getting it right. I used a drill bit and it was not the best choice come to find out.
@DocsBoost
4 ай бұрын
Okay, I also ended up with the hole too big and I had to buy another install kit. Before I used the second kit, I went to the hardware store and bought myself a large flat washer with a diameter just a bit greater than the beauty ring that comes in the install kit. I used a step drill to make the hole a tight fit on the insert. I mean it was a very tight fit. Then I tack-welded the washer in position and everything worked perfectly.
What company make is your hood? Thanks
@DocsBoost
Күн бұрын
Mamba
@DocsBoost
Күн бұрын
BMC Extreme Customs: Ford Mustang GT500 Black Mamba Hood 2010-2014 www.bmcextremecustoms.net/20fomugtshsu.html. I bought a relocation kit for the windshield washers along with the hood.