How To Install Piston Rings On a 4 Stroke Piston
Автокөліктер мен көлік құралдары
Follow along as we install our properly gapped piston rings on our new weisco piston. Please comment with any questions! Thanks for watching and as always please subscribe!
Пікірлер: 44
Most helpful vid so far I’m trying to rebuild xr80 top end
How can I tell the top ring from the button if there is no n mark?
Great video very helpful 🍻
Excellent video
I just purchased a 800 CC big bore kit from my GY6 and I'm installing the rings and I can not get the oil ring to in close into the boar I don't get why but it's not overlapping but when it's not overlapping it's sticking out too far
On the 2 top rings are they different ,is the very top ring shiney or ticker than the 2nd one,someone said the top one is shiney and the second dark color,and maybe the 2nd is thicker?Thanks..
Hey brow i am trying to overall a 4JB1 .i have no experience. But i would like some guidance on the rings replacement And how to set the timing thank u
Is it same for all 4 strokes
Cool
Are you still working on quads im in NYC brooklyn actually I have a old Suzuki LT230 GE I want to rebuild it its all running and stock and just want to basically tune up and rebuild stock
good video.. Is there a certain way ( meaning facing up or down) the second an third go in?
@grindinggearsgarage9578
7 жыл бұрын
Kaution Diaz usually the second one will. The oil seals or lower set does not matter
I will try this
Wiseco instructions, illustration 1, has a line running through the pic of the piston called "piston pin center line". What the hell does that mean? It's confusing. Front of the bike is exhaust.. correct?
@samuelyeet6006
4 жыл бұрын
Depends on your bike, some bikes have the exhaust in the front, some have them in the back
@richardbartlett4075
4 жыл бұрын
On illustration 1 on the orange instruction sheet - forget the arrow with the "engine front". The piston pin center line is where the wrist pin will go. So at the top of the illustration, is actually the direction towards the front of the engine or towards exhaust. The oil ring expander gap should be as shown, 90 degrees from the WRIST PIN, as the written instructions say. Not aligned with the wrist pin.
Hi just thought I'd say that it doesn't matter which way the ends on the oil ring sepetator are facing. You said they need to be faced up but it really doesn't matter. Just posting this to help anyone out there who's installing rings.
@cesarzentil4463
7 жыл бұрын
But other then that this is a great video
@grindinggearsgarage9578
7 жыл бұрын
Hey thanks man! I always appreciate the help!
the Wiseco instructions are actually confusing. The engine front points left (9 oclock) and the "center line" also goes left to right (3 oclock to 9 oclock). I assume the center line is the Piston Pin bore. That being the case the front of most atv engines point to 12 oclock or exhaust port. Not sure why Wiseco's diagram is the way it is and it creates uncertainty regarding placement
Great video. I have a 92 susuki quadrunner it ran good I full trothle it when I got it running. Then came home and now no compression. It blows it back to the carburetor. Any idea what it could be?
@Doitallbros
10 ай бұрын
If it blows back the air through the carburettor than you have to tack the cylinder head off and put the piston to the bottom and put it so next valve opens is air/petrol valve
@Doitallbros
10 ай бұрын
It is the valves are not sync with the piston
@pedritoc.c.t.665
10 ай бұрын
@@Doitallbros ok lo buscare .
@pedritoc.c.t.665
10 ай бұрын
@@Doitallbros I meant ok I will look in to it
Will a head gasket for a different Kawasaki fit on a Kawasaki prarie
@grindinggearsgarage9578
6 жыл бұрын
not really sure
@liveandletlive2894
4 жыл бұрын
A bayou 400 yes.
Rings not properly visible . Please make another video. Overall good work
most difficult part is allways getting the darn cilinder over the piston while compressing the rings... Do you have any tips on that?
@brycewatson3387
3 жыл бұрын
A piston ring compressor compresses them for you before putting them in so that it slides in no problem.
Great video. Does bottom middle wavey ring have an up or down? Does it matter which way the pointed ends face when butted up next to each other?
@jordanlittle5391
4 жыл бұрын
he states it in vid
@mikeoneal4882
4 жыл бұрын
Watched again. Points facing up, got it. Thank you
thanks very helpful. i made the mistake of buying a cheaper piston and it came with no instructions.
@grindinggearsgarage9578
7 жыл бұрын
awesome thanks for watching!!!!
I was rather hoping you'd show us you actually installing the rings.
do not use mobile camera >>> use tripode and do not move so much with your camera, it makes us dizzy
That does not compute!
Nice video man!! I also do video about motocyrcle, so if you want check my channel :D
@grindinggearsgarage9578
8 жыл бұрын
Of course man! Subscribing now!!!!
The poorest video i have ever seen
Again a video with zero detail for ring identification.